Question about Weiser Lock POWERBOLT ELEC DEADBOLT

Open Question

Entered three wrong codes how to fix

I went to feed our kids dog while they are away and I made an entry mistake on the key pad three times and now it won't respond to the correct code. Does the lock reset itself automatically after a period of time. If so how long will it take?

Posted by Anonymous on

Ad

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
sonicboomele
  • 1557 Answers

SOURCE: How do I reprogram the

  • Remove the inner cover plate from the lock.
  • Locate the small round reset button near the left side of the circuit board (Red or Black).
  • To program, press the reset button once, then enter your 4-8 digit code on the exterior keypad, then immediately press the middle lock button on the exterior keypad. You will hear a beep. This signals that your code has been accepted.
  • To enter a second code, follow the same procedures as in step 3, but this time press the reset button twice then enter your code.
best of luck.

Posted on Aug 02, 2010

Ad
  • 15 Answers

SOURCE: we are trying to reset

  1. To program the first code, press the reset button once, then enter your 4-8 digit code on the exterior keypad, then immediately press the middle lock button on the exterior keypad. You will hear a beep. This signals that your code has been accepted.
  2. To program the second code, press the reset button twice , then enter your 4-8 digit code on the exterior keypad, then immediately press the middle lock button on the exterior keypad. You will hear a beep. This signals that your code has been accepted.
  3. To program the third code, press the reset button 3 time, then enter your 4-8 digit code on the exterior keypad, then immediately press the middle lock button on the exterior keypad. You will hear a beep. This signals that your code has been accepted.
Good lock
Good unlock

Posted on May 15, 2011

  • 963 Answers

SOURCE: My pwerbolt is about 3

This is the relevant excerpt from the Powerbolt programming and troubleshooting instructions:

"To determine why your lock is beeping abnormally, please follow these steps:

Take out batteries and unplug powerstrip.
Let it sit for 1 minute, then put the batteries back in and wait another minute.
If it does not beep, the keypad needs to be replaced (17733-1).
If the unit continues to beep, the powerboard needs to be replaced (A17734-3,3 Powerboard 1470 brass finish; A17734-3,26D Powerboard 1470 satin chrome finish; A17734-3,5 Powerboard 1470 antique brass finish)."

Since you've already gone through the battery change, try the battery remove-reinstall recommended above. If that doesn't work for you it suggests that you need to replace the appropriate Powerboard for your lock.

So this is the link to Weiser Customer Support Page, where you will find the appropriate number of your location:

http://www.weiserlock.com/en/CustomerService/ProductSupport/SupportContact.aspx

I suggest calling the appropriate toll-free number and having a conversation with a representative about this problem. You will want confirm that you need the part before you go through the expense, and that it's worth it. You will need to know the "finish" of your lock. Try to talk them into warrantying the part, in spite of the age (one year warranty on electronics), as a matter of good customer relations. They will help you get the correct part on order.

Good luck--and please provide feedback if this helps!

Posted on Aug 24, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I train a three year dog to use dog pads when nature calls her.


You have to get the pads with the pet scent on them. Most of the time pads dont work for potty training.

Feb 05, 2015 | Hartz Training Pads for Dogs-50-Pads

1 Answer

Ford keyless entry key pad needs to be disabled


Google the programming instruction for the key pad and reprogram the system to the code of your choosing

Nov 06, 2013 | 2005 Ford Five Hundred

1 Answer

On the screen it says END how do I get it to read code-----


If you entered the wrong code more than three times, you need to leave the radio on for an hour or two in order for it to reset back to code entry.

Mar 03, 2013 | Car Audio & Video

1 Answer

The feed dogs of my shark 801B don't go up how can I fix that


the machine needs to be checked to see if the feed dogs broke
or were damaged

Jan 23, 2013 | Sewing Machines

1 Answer

3385 Eurovox, wrong code entered three times.


It thinks it has been stolen! check the owners manual, or the mfgs website for more info. there is a specific input sequence for each one

Jul 26, 2010 | Car Audio & Video

1 Answer

How do I change the code for key less entery on the key pad on door


Programming a personal entry code The factory set code cannot be reprogrammed but you can create your own 5 digit personal entry code. When pressing the controls on the keypad, press the middle of the controls to ensure a good activation.
Up to three personal entry codes may be programmed to the vehicle. To create your own personal entry code:

  • 1. Enter the factory set code.
  • 2. Within five seconds press the 1-2 on the keypad.
  • 3. Enter your personal 5-digit code. Each number must be entered within five seconds of each other.
  • 4. Press 1-2, 3-4 or 5-6 to indicate which of the three personal entry code positions you wish to use.
  • 5. The doors will again lock then unlock to confirm that your personal key code has been programmed to the module.
Tips:

  • Do not set a code that uses five of the same number.
  • Do not use five numbers in sequential order.
  • The factory set code will work even if you have set your own personal code.
  • If you program a code to a position that already contains a set code, the previously-set code will be erased.

Erasing personal code
  • 1. Enter the factory set 5 digit code.
  • 2. Within five seconds, press the 1-2 on the keypad and release.
  • 3. Press and hold the 1- 2 for two seconds. This must be done within five seconds of completing Step 2.
All personal codes are now erased and only the factory set 5 digit code will work.

Good luck (remember commend and rated this).

May 03, 2010 | 1996 Ford Explorer

2 Answers

I need the mercedes benz 1999 clk 430 radio code


AR82.60-P-7502-01A Coding Radio
(MODEL all with CODE (750) Radio Becker Europa 2000 with CODE (751) Radio Becker Grand Prix 2000 with RDS)

  1. If the radio is disconnected from the power supply, it is not operational when re-connected. After switching on the ignition and the radio, the readout CODE appears in the display.
  2. The code number for the radio is advised to you on the enclosed CODE CARD.
  3. To enter the first digit of the code number, you have to continue pressing station button 1 until the correct digit appears in the display. Adopt the same procedure for the second, third and fourth digits.
  4. Once you have entered the correct code number with the station buttons 1, 2, 3, 4 and confirmed the entry with the SEEK button (press down), the readout CODE disappears. The radio can now be operated.
  5. If you enter a wrong code three times, you must wait 15 minutes before making a new entry. In addition, if 9 incorrect entries are made, the radio will then not operate for 24 hours. During this time the radio and the ignition (terminal 15) must remain switched on.
AR82.60-P-7502-01B Coding Radio
(MODEL all with CODE (353) Audio 30 APS with CODE (510a) Radio MB Exquisit with traffic news decoder, with RDS (Becker) with CODE (512a) Radio MB Special with traffic news decoder, with RDS.)

  1. If the radio is disconnected from the power supply, it cannot be operated by simply reconnecting. After switching on the ignition and the radio the word "CODE" appears in the display on the radio.
  2. The code number for the radio is given on the enclosed CODE CARD.
  3. Enter the code number with the station button, e.g. number 1, station button 1. After entering the first number the word "CODE" disappears and the number entered appears followed by 4 dashes. The next character to be entered flashes. After entering all five numbers, the first character starts flashing again. In this state the code number can be written over as frequently as desired. A correction can be made only by entering the complete code number again.
  4. Confirm code number: Press TUNE, AUTO/SEEK or SC button. The radio automatically switches on and indicates the radio station or frequency stored with station button 1.
  5. If an incorrect code number is entered and confirmed, the word "CODE" appears again on the display. If an incorrect code is entered three times the word "WAIT" appears on the display and the radio locks up for approx. 10 min. If the code is entered incorrectly three times again the radio locks up again for 10 min. Three more incorrect entries (a total of 9 incorrect attempts) increase the lock-up time to 60 min. Another three incorrect entries lock up the radio for another 60 min. The waiting time runs only when the radio is switched on.

Dec 17, 2009 | 1999 Mercedes-Benz E-Class

1 Answer

Error code c0-510 come on a konica bizhub 350


Fusing error
1. Press the Warm Restart switch, and “●” appears at the center on the left end of the screen.
2. Enter “3” from the 10-Key Pad.
3. Type the 8-digit service code and touch [Enter]. (Default value: 00000000)
NOTE
• When [END] is touched after a wrong service code has been entered, the Basic screen reappears.
• At the fourth access after entries of three wrong access codes, [END] is not available on the screen. It is therefore necessary to turn OFF and ON the Main Power Switch.
• If you forget the service code, it becomes necessary to replace the RAMS Board with a new one. Take necessary steps not to forget the service code.
• The RAMS Board is not available as a replacement part. If it requires replacement, contact Office Printing Support Division by way of CSES.

Reset your Toners and Imaging units for Minolta Bizhub and CF series.
http://www.chipreset.eu

Jul 23, 2009 | Konica Minolta bizhub 350 All-In-One Laser...

2 Answers

Kenwood ddx512


The unlock code usually only goes on if you previously put one on there. I would suggest calling Kenwood but there is a guy that claims he can fix this i have never tried this but you can. http://mike-unlockcodes.blogspot.com/

Apr 24, 2009 | Kenwood DDX-512 Car DVD Player

1 Answer

NEED PUK CODE:::


you have entered the pin code wrong 3 times now you are required to enter a puk code to reset the pin code. 

The puk code is sim card spesific it comes with the sim card when you get it or you can get it by calling your phone service provider of the sim card to get the puk code. 


if you have entered the puk code wrong too many times you will make the sim card useless and you will have to contact your phone service provider for a new sim card, it will probably cost.

Dec 18, 2008 | Nokia 9300 Smartphone

Not finding what you are looking for?
Weiser Lock POWERBOLT ELEC DEADBOLT Logo

Related Topics:

170 people viewed this question

Ask a Question

Usually answered in minutes!

Top Weiser Lock Locks & Locksmithing Experts

Azam Ali

Level 1 Expert

31 Answers

Scoee Scoffer

Level 2 Expert

162 Answers

Cindy Wells

Level 3 Expert

6032 Answers

Are you a Weiser Lock Lock and Locksmithing Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...