Question about Zebra 105SL Thermal Label Printer

Open Question

My ZDesigner LP 2844 is connected to Windows XP laptop. I'm using it to print FedEx RMA labels. However, every time I print the RMA label the receipt part comes out fine (4x6) but the shipping label prints only (2x4) I've tried to change settings, (e.g. size, stock, etc.) but the shipping label still prints 2x4 on a 4x6 label. Any help would be greatly appreciated.

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
  • 130 Answers

SOURCE: Trying to Print USPS Labels from PayPal on TLP 2844

see if you can set the printer preferences to borderless printing.

Posted on Jun 14, 2009

Ad

SOURCE: which driver to use with lp 2844-Z under windows

Go to website below, and download the driver from there unplug device, install software and reboot, at next desktop, NOW plug in the unit and use.

Posted on Mar 23, 2010

  • 226 Answers

SOURCE: Networked LP 2844 not printing full labels

try microsoft word 07 and print

Posted on Mar 27, 2010

  • 97 Answers

SOURCE: Zebra LP 2844 doesn't feed label all the way out

Hi Brian,
When the last label printed is still under the printhead, that means the printer is in "rewind mode". There should be an option for "tear off" mode in the printer driver. This is the mode that pushes the last label printed out to the tear bar. The printer will then "backfeed" when printing the next label. Peel off mode is used if you want to print a label and have it "peeled" off the liner so that you can just pick up the label off the liner and apply it. That takes the rewind option to be installed.
Watch out though, if you are using a label software package, there might be a setting in the label format setup for "tear off" which usually overrides the settings in the printer.

Hope that helps !

Posted on May 06, 2010

duane_wong
  • 6826 Answers

SOURCE: Won't print last inch on label

http://www.zebra.com/id/zebra/na/en/index/service_support/options/technical_support.html?country=US&product=58

contact tech support for Zebra LP 2844 Thermal Printer.

Posted on Jul 21, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Label splits


because if label lengh is ex. 20mm and you set up label print area as 21mm, it will over the size and it will skip the next one. the print area shoul be less than the label length. please verify software or driver.

Jan 22, 2014 | Zebra LP 2844 Thermal Printer

1 Answer

My Zebra ZDesigner LP2844 feeds a blank label after printing a label. How do I make it stop doing that?


Define your label size correctly. Measure your LABEL exactly, do not include the backing paper or the gap. Calibrate the printer. HOW?
Power off printer. Press and hold the green feed button down and power printer on. Count one, two and release green button. The printer will calibrate and move labels and then print some stuff on the label. Wait until it has comletely stopped. wait another few seconds and the press the feed key once. The printer will print "out of dump". You should now be ready to print again.

Aug 31, 2013 | Zebra LP 2844 Thermal Printer

1 Answer

Hi I am printing barcode labels on a Zebra Tlp2844-Z. I can print resident barcodes in passthrough mode using the old Zebra driver (1.0.0.43) but the barcode does not print using the ZDesigner driver...


Have you tried creating the barcode / label using the ZDesigner software? It is available free on their website and I'm sure you'll find it easy to use. Hope this helps!

Aug 23, 2011 | Zebra TLP 2844-Z Thermal Label Printer

1 Answer

I have Zebra LP 2844-Z printer and the barcodes


Here are 3 suggestions.

1
Check that your label size definition is correct, measure your label height in mm and check that your printer driver settings match.

2
Perform a calibration. How?? when printer is on labels loaded and green light, hold feed key and wait for 2 blinks then release feed key. (If you release it after 1 flash you will print a configuration label)

3
If you are using Zebra Designer, download latest version of Zdesigner V2. Install latest printer driver V2.63. This driver & Zdesigner allows you to calibrate the printer directly from within Zdesigner. Go to File/Printer settings/ advanced options and click calibrate at bottom of page. when printer calibrates then tick the box USE PRINTER SETTINGS and printer will now work properly.

Jul 01, 2010 | Zebra LP 2844-Z Thermal Label Printer

1 Answer

Which driver to use with lp 2844-Z under windows XP to print USPS 4x6 labels in portrate mode if lpt1 is used?


Go to website below, and download the driver from there unplug device, install software and reboot, at next desktop, NOW plug in the unit and use.

Mar 23, 2010 | Zebra LP 2844 Thermal Printer

1 Answer

Zud - print error - under temperature


Try using the latest zebra printer driver. The ZUD driver has been superceded by the latest Zdesigner driver which works in Zebra Designer and any windows application

Jun 09, 2009 | Zebra LP 2844 Thermal Printer

4 Answers

I need the driver for Zebra LP 2844 for MAC OS X.


OS X 10.5.2 and above have built-in ZPL and EPL drivers. Plug the printer in to USB, go to System Preferences > Print & Fax, click + , and choose the Zebra driver. For the LP2844 you choose the EPL2 driver.

Apr 09, 2009 | Zebra LP 2844 Thermal Printer

3 Answers

Wont print


Check to make sure you have direct thermal labels. You can test this by scratching your fingernail across the label quickly. You should see a black line. This printer uses the same paper as a ups or fedex label. test a ups of fedex label with the fingernail test. Does it look the same? or call Andrew @ 908-725-1699

Jun 17, 2008 | Zebra LP 2844 Thermal Printer

Not finding what you are looking for?
Zebra 105SL Thermal Label Printer Logo

Related Topics:

38 people viewed this question

Ask a Question

Usually answered in minutes!

Top Zebra Office Equipment & Supplies Experts

Gateway information...

Level 2 Expert

252 Answers

Marvin
Marvin

Level 3 Expert

85111 Answers

Joaquim Martins

Level 3 Expert

1127 Answers

Are you a Zebra Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...