Question about Tomtom ONE GPS Receiver

1 Answer

Tom Tom one Will not perform setup, locks up at voice selection.

Device was working fine for 4 months, until the 23rd. Used it to navigate to an address, worked. Turned off. When I turned it back on to navigate to a different address unit did some sort of reset turned itself off, rebooted and came on in the setup mode. Performed setup steps but will not go pats voice selection. Tried different things but when a button is selected in "voice selection" -Cancel, -Select, the device freezes for about 60 sec then restarts again in the setup mode. You can cycle through the voices and "test" them but you can't save a voice.

Posted by on

  • dan_geshell Jun 24, 2009

    Did not work; however I just tried the operate GPS device with Tomtom Home. Using the PC to control the Tomtom worked, I performed the setup and now my "One" functions once again.

×

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 14 Answers

Try doing a man reset.

Posted on Jun 24, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How can I start using my new Nuvi 2569 sat nav?


Step Description Step 1:
Warm Up If possible, let the GPS warm up for a few minutes once turned on. This allows the GPS to acquire its current position via satellite. Step 2:
Determine Preferences Choose day or night colors to display a suitable screen for the time of day. Step 3:
Adjust Volume Adjust the volume so the device can be heard over traffic noise. Step 4:
Enter Address Through the onscreen navigation option, enter the street address for the destination. Step 5:
Verify Route Check the listed route for accuracy, adjusting as needed. Step 6:
Follow Directions Follow the directions given by the GPS device to reach your destination. Some models, especially in-vehicle navigation, offer voice directions. Step 7:
Turn Off Once you've reached your destination, turn off the GPS device to save its battery charge. Step 8:
Store Device Store the GPS device out of sight if possible, or take it with you to prevent theft.

Mar 27, 2016 | GPS

1 Answer

Acura navigation system stopped working


I have a 2007 Acura TL. The navigation system worked well, until 2017, when I decided not to renew it. Everything started to go wrong. It worked intermittently. Cost me job interviews, getting lost and being late. Did you receive a message, "See your dealership"? Well, the dealership was charging the same as the renewal price. A coincidence or an attempt to force the renewal? Well, I gave in. I just received the new navigation system (disc). It hasn't been installed as yet. Try reprogramming and find out how old the system is. A great car. The turning radius and the navigation system are my problems. Good luck.

Jan 30, 2018 | 2008 Acura TL Type S

1 Answer

Do not know how to program the systemlink3 universal t,v. remote control to my t.v.


Option 1:
To clear things up and make it simple, here is how to program the RCA Systemlink 3 remote:
****WITH DEVICE TURNED ON****
  1. Press and hold the "Code Search" button until the LED lights, then release. LED will stay light.
  2. Press and release the device key to be programmed. LED will go off when button is pressed and back on when released. LED remains on.
  3. Press and release the remote On/Off (power) button as many times as required to turn your device OFF.
  4. When device turns OFF, press and release the ENTER button.
Test remote on device, if ALL functions do not work, repeat above procedure.
***IMPORTANT NOTE***Count how many times you press the On/Off button. If ALL funtions do not work and you need to repeat, you don't want to stop at the same non-working code. For instance, if it takes 23 times to turn your device off and after testing, the remote does not control all functions, repeat steps 1-3 BUT when the device turns off at the 23rd time, turn it back on using the power button ON THE ACTUAL DEVICE then continue with step 3 and 4 from above.


Option 2:

Thanks for the hints on your web site. For the RCA SystemLink 3 with the key pad, I could not get the sequences described to work. But they did point me in a direction which worked for my remote:
  • With the TV on (for TV)
  • Press and hold code search until the light stays on
  • Press TV (for TV) button once
  • Press the on/off button once
  • Thereafter, the light will stay lit and every couple to three seconds it will blink twice indicating it is trying another code.
  • When the TV turned off, I pressed enter. Thereafter the unit worked.

May 04, 2011 | RCA Televison & Video

1 Answer

Garmin nuvi 255 won't turn anymore


i had same prob about a month ago it sorted it's self out after left on charge for a week

Jan 20, 2010 | Garmin Nuvi 255 GPS Receiver

1 Answer

No ip address was asigned from dlink to laptop


Is your DHCP turned on in the D-Link ? It cannot assign an address if it is not enabled. Also bear in mind that a pc may take up to 2-3 minutes to "get" an address - it is relative to the broadcast and beacon interval of the router and the query time of the pc lan card. If DHCP is turned on in the router and it has an address pool, try restarting the PC, if the router has used up it's pool of assignable addresses, it maybe "locked" and cannot release a new one, try pressing the reset button on the router, it is inside a little hole in the back, a pencil works fine for that, hold it until all the lights go out on the front and start flashing. Then restart the pc and it should get an address.

Aug 30, 2009 | Computers & Internet

2 Answers

Hard drive error


same exact problem let sit for several months went to turn on and all i could see was a "hard disk error" message flash very quickly and then turn off. after months of no help online i decided to open
my jukebox 20 and there are 4 ni-cad batteries inside. i removed batteries and replaced with 4 "AA"
regular energizer batteries and it works fine. at least until i extract my 1000 songs and put them on another device so i ll never lose them. GOOD LUCK.

Mar 08, 2009 | Archos Jukebox Studio 20 MP3 Player

1 Answer

Need code # for rca tv


If your remote control has a search button, this is how you do it-------- User submitted information for the SystemLink 3: To clear things up and make it simple, here is how to program the RCA Systemlink 3 remote:
****WITH DEVICE TURNED ON****
  1. Press and hold the "Code Search" button until the LED lights, then release. LED will stay light.
  2. Press and release the device key to be programmed. LED will go off when button is pressed and back on when released. LED remains on.
  3. Press and release the remote On/Off (power) button as many times as required to turn your device OFF.
  4. When device turns OFF, press and release the ENTER button.
Test remote on device, if ALL functions do not work, repeat above procedure.
***IMPORTANT NOTE*** Count how many times you press the On/Off button. If ALL funtions do not work and you need to repeat, you don't want to stop at the same non-working code. For instance, if it takes 23 times to turn your device off and after testing, the remote does not control all functions, repeat steps 1-3 BUT when the device turns off at the 23rd time, turn it back on using the power button ON THE ACTUAL DEVICE then continue with step 3 and 4 from above.

Nov 19, 2008 | RCA 3-Device Universal Remote with...

1 Answer

Will not pair to phone...Worked fine until today


re: Carmen66. Your advise 'bluetooth' "device is out of range or powered off", worked like magic. Yes, it's a pain to power off the phone and restart it before connecting the bluetooth, but heck it works. Reboot, so simple, inconvenient, but works with GREAT success! Thnk You.Very Helpful. First new phone in a few yrs and was ready to take it all back.

May 07, 2008 | LG enV VX9900 Cellular Phone

2 Answers

Cannot insert addresses!


Got it!! For those getting the "No Matches Found" headache. Here's the solution:1. Go to "Settings" 2. Go to "Map" 3. Go to "Map Info" 4. MAKE SURE that "City Navigator North America NT 2008" is CHECKED. It fixed the problem for me. Hopefully it will fix yours all the same. God Bless.

Apr 02, 2008 | Garmin nuvi 350 GPS Receiver

Not finding what you are looking for?
Tomtom ONE GPS Receiver Logo

1,398 people viewed this question

Ask a Question

Usually answered in minutes!

Top Tomtom GPS Experts

LP

Level 3 Expert

514 Answers

k24674

Level 3 Expert

8081 Answers

Marvin
Marvin

Level 3 Expert

85161 Answers

Are you a Tomtom GPS Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...