Question about Xerox Phaser 8500/DN Printer

Open Question

Xerox Phaser 8560 error code 09,037.45:9180. Does anyone know what this error code means?

I got this error code when the printer was warming up. It rebooted itself then brought this error message up. It said to try to turn off and wait then turn back on. I did this 3xs and it still comes up.

Posted by Anonymous on

Ad

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
  • 526 Answers

SOURCE: Phaser 8560 error code

Most likely you are using generic ink or ink not made for that specific machine. The black ink is the one causing the problem. the printer will then need to be reset.

Posted on Apr 15, 2009

Ad
darkpain
  • 316 Answers

SOURCE: xerox phaser 8560 error 04,018.48:26

Hello,this fault code indicates a problem with the process control system.The printhead temperature dropped below the head cleaning needed threshold and that's why stops warming up.The first you need to do is to verify the temperature of the room that the printer is,if its too cold,near from an open window...If was too cold and not in the room temperature then move the printer and your are done.If this doesn't solve your problem run the Monitor Heaters tests with all heaters ON.Are the heaters operating correctly?If yes replace the Electronics Module.If no you have to inspect the harness to the failed heater.Is the harness damaged?If yes you must replace the harness.If no replace the problem component.
Good luck:)

Posted on Feb 04, 2010

pineworks
  • 4345 Answers

SOURCE: Xerox Phaser 8560 - error code 09 037 45 108564

Hi there

That's a ink loader error, due to the 8200 ink stick; to fix it:

- Power down the printer.
- Hold the back button and the info button at the same time, without letting go, power up the printer.
- Keep holding down the buttons until the XEROX logo comes fully to the center of the screen, keep holding for 2 more seconds, then let go. I'll take about a minute or two for the Diagnostic screen to come up, the display will turn blank and black.
- When the Diagnostic screen comes up go to down to the Function or Exercise option, there will be an option that says "clear ISC faults" it'll ask you to press OK to confirm, after you do then you will exit Diagnostics and the printer will reboot.
It should be fine until it happens again. Until all the 8200 ink is gone you will probably be doing this a few more times. Also make sure the 8200 ink is not jammed inside the ink loader, if it is then you have to un-jam it some how.

Please come back and just gave a vote, it will gave me some satisfaction to know am helping some one so I will keep on helping.

All The Best: Pineworks

Posted on Mar 02, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Error message on xerox 8560 09,038.46:13269


Go to the Xerox.com website and follow the troubleshooting aid to these types of faults.
Good luck.

Feb 26, 2015 | Xerox Phaser 8560/YN Printer

1 Answer

Can anyone tell me what code 19,003.48 means for Xerox 8560?


19,003.48: Scale and offset error is too large. The voltages measured have more than a 20% error from their expected values. Something is wrong with the Electronics Module or the Wave Amplifier.
To prevent these discharges, a Grounding Clip (P/N 650442700) was added between the Y-Axis Motor mount and the Pick Clutch. Check that this clip is installed and contacts the metallic portion of the Pick Clutch.
Note
The Grounding Clip is factory installed in later versions of 8500/8550
models and in all 8560 models.

Oct 14, 2014 | Xerox Phaser® 8550, 8560, 8560MFP Extended...

1 Answer

Xerox Phaser 8560DN error code 07,010,43


Sadly, Xerox says that this means "Power off the printer and contact support". Phaser 8560 Support Drivers

However, there is something about "opening the pivot plate", it's Greek to me, but google it and see if you can't reset the brain in the printer and get it back to life without an expensive service call.

Aug 23, 2014 | Xerox Phaser 8560DN Laser Printer

1 Answer

Xerox 8560 error code 07,007.40


That error signifies a problem with the printhead tilt, you need to replace the Process motor camshaft pivot kit, part number 8560-Z2.
http://www.iteminconline.com/8560-z2_8560-z2-xerox-8560-process-motor-camshaft-kit.htm

Feb 07, 2014 | Xerox Phaser 8500/DN Printer

1 Answer

On the 8560, what does the error code 07,010.43:14070 mean??


Hi,
In the Xerox support website that error indicates that the printer needs to be turned off and call for xerox assistance. Does not specify the problem.

Although, this website refers to this problem.

http://www.fortwayneprinterrepair.com/wordpress/2011/09/25/xerox-phaser-8400-8500-8550-8560-07010-43-error-message/

If the printer has only one year old, the best solution will be to call for xerox assistance because it is under warranty.... I think...

Aug 08, 2012 | Xerox Phaser 8560MFP Laser Printer

1 Answer

Xerox phaser 8560 error 04,018.48:26


Hello,this fault code indicates a problem with the process control system.The printhead temperature dropped below the head cleaning needed threshold and that's why stops warming up.The first you need to do is to verify the temperature of the room that the printer is,if its too cold,near from an open window...If was too cold and not in the room temperature then move the printer and your are done.If this doesn't solve your problem run the Monitor Heaters tests with all heaters ON.Are the heaters operating correctly?If yes replace the Electronics Module.If no you have to inspect the harness to the failed heater.Is the harness damaged?If yes you must replace the harness.If no replace the problem component.
Good luck:)

Feb 04, 2010 | Xerox Phaser 8560DN Printer

2 Answers

Phaser 8560 error code


Most likely you are using generic ink or ink not made for that specific machine. The black ink is the one causing the problem. the printer will then need to be reset.

Apr 15, 2009 | Xerox Phaser 8500/DN Printer

Not finding what you are looking for?
Xerox Phaser  8500/DN Printer Logo

Related Topics:

43 people viewed this question

Ask a Question

Usually answered in minutes!

Top Xerox Office Equipment & Supplies Experts

Clive
Clive

Level 3 Expert

4345 Answers

Philip Hughes

Level 2 Expert

80 Answers

docukaaf

Level 1 Expert

38 Answers

Are you a Xerox Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...