Question about Zebra 105SL Thermal Label Printer

Open Question

Zebra zm400 error cleared head open - Zebra 105SL Thermal Label Printer

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
  • 35 Answers

SOURCE: Zebra 140xi II error

If you open the case there is a sensor that detects whether the head is opened or not that is connected to the open and close lever. Sometimes the tab that blocks the sensor when it is closed get out of alignment or comes loose or the sensor is jarred loose. Make sure the tab breaks the beam.

Posted on May 12, 2008

Ad
bartech9
  • 155 Answers

SOURCE: printing error condition

First clean the sensor tag and sensor head open and tape. Then perform a calibration label pressing the PAUSE and FEED buttons and turn on the printer, release the keys until it starts to move the label. Wait until you are finished and ready to print.

Posted on Mar 16, 2009

bartech9
  • 155 Answers

SOURCE: Zebra 220xiIII Error Condition Head Open will not go away

The head open sensor is inside the printer is detected by the gear head.

Posted on Mar 16, 2009

seltzercool
  • 21 Answers

SOURCE: my zebra printer s4m is saying ALERT CLEARED HEAD

Alert Head Open will show everytime u open the Head , when u close back the head it will show Alert CLeared Head Open, then it's normal.

Ribbon Out Show means the printer doesn't detect a ribbon, make sure there's nothing wrong with ribbon installation. if everything fine, then the problem is you Ribbon Sensor. u can try to adjust the sensor with a screwdriver ( - ), make a little bit higher

Posted on Aug 20, 2009

ozztech
  • 285 Answers

SOURCE: como cambiar ip de zebra zm400 desde el panel

you need to connect with some network to the ip adress coming on the setings, if you dont connect with network, that function not apper.
If connect, you be aple to change to IP estactic and the Gateway and the subnet mask.
Dont forget to save.

Posted on Nov 13, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

LA IMPRESORA ZEBRA ZM400 CUANDO SE ENCIENDE APARECE EN LA PANTALLA LCD, EL MENSAJE HEAT OPEN, COMO QUITARLO?


there is a possibility that you need to just the print head assembly, if when its at close position, the print head is far from the sensor.

With the print head is open, you will see 3 screw on the left, louse them and adjust all the print head mechanism, up and down some milliliters tie the screws again, close the printhead , try again and see if errors desapeer

Jul 24, 2014 | Zebra ZM400 Thermal Label Printer -...

1 Answer

How to solve this problem in zebra zm400 error condition paper out \


check the sensor under the paper, reload labels roll, labels are possible on top of sensor black plastic and not between. move gap sensor to midle of label with. check manual to know how to fit the labels thought the sensors and printhead.

Sep 17, 2013 | Zebra ZM400 Thermal Label Printer -...

1 Answer

Zebra printer drops network


i hadthe same issue with all my zm400's, but not my zm4 plus's. zebra gives you the run around when contact their technical support.
I tried every setting there was, ended up get rid of the zm400's, they are a piece of C#@P

Feb 03, 2012 | Zebra ZM400 Thermal Label Printer -...

1 Answer

The message "head open " printer idle v53.16.5z


Try taking the printer off pause. It should clear the error.

Mar 03, 2011 | Zebra ZM400 Thermal Label Printer -...

1 Answer

I have a zebra zm400 prinetr givig me an error message (head element bad)


turn printer off, press PAUSE button, turn printer on and wait 5 seconds then release the button. The printer is going to print the test label, check if coming some withe lines across the print. try to clean the printhead and the rollar, if pressist, need to replace printhead.
Please check if the cable from the printhead is totaly plug-in

Oct 15, 2010 | Zebra 105SL Thermal Label Printer

1 Answer

Error in position of the output for ZM400


this is usually caused by a pressure imbalance across the printhead. Check the printhead pressure adjust dials located on top of the printhead. You might find that the left side has more down pressure than the right side causing the ribbon to move to the right.

Hope that helps !

Apr 09, 2010 | Zebra 300DPI CUTTER [zm400-3001-1000t]...

1 Answer

Zebra zm400 turn printed info 180 degrees


Yu can rotate the print orientation in the Z Designer printer driver, in the OPTIONS tag tick the 180Deg box

Dec 17, 2009 | Zebra 300DPI CUTTER [zm400-3001-1000t]...

1 Answer

Error condition ribbon out in ZM400


In the printer setting-

Change the Print Method from - "Tharmal Transfer to Direct Thermal" and save it permanently

Aug 10, 2009 | Zebra 105SL Thermal Label Printer

1 Answer

Zebra 220xiIII Error Condition Head Open will not go away


The head open sensor is inside the printer is detected by the gear head.

Mar 16, 2009 | Zebra 220XiIII Label Printer

3 Answers

ZM400 printer


Try going through the LCD menu and if it say "Direct Thermal" change it to "Thermal Transfer", Direct Thermal made means, no ribbon required, but it sounds like you do have ribbon in the printer, if so, try my recommendation. If it asks for a password, it's '1234'.

Oct 14, 2008 | Zebra 203DPI Printer

Not finding what you are looking for?
Zebra 105SL Thermal Label Printer Logo

Related Topics:

1,059 people viewed this question

Ask a Question

Usually answered in minutes!

Top Zebra Office Equipment & Supplies Experts

Gateway information...

Level 2 Expert

252 Answers

Marvin
Marvin

Level 3 Expert

85160 Answers

Ekse

Level 3 Expert

13434 Answers

Are you a Zebra Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...