Question about Sharp AR-5516s

Open Question

My sharp machine ar 5516s is having problems giving error code l and 4 simulteniously what can i do

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
  • 62 Answers

SOURCE: error code

Hi, H4 is a heater error. Try resetting it by the following; Enter #, interupt, Clear, interupt, display goes dead, enter 14 then print. That will clear the error code, however if you have a problem with the heater it will return. It is probably the thermal fuse has tripped, which is resetable by removing the fuser unit

Regards

Andy

Posted on Jan 22, 2008

Ad
  • 126 Answers

SOURCE: Error Code F1-87 Finisher Trouble on Sharp AR-M350U+

It is a stapler rotation error. The stapling tray pressure arms become dull at the tips, so when the stapler attempts to move into position to make the staple it cannot move the guides out of the way.

First choice) Replace the (4) stapling tray pressure arms (LSTPP0357FCZZ). After you replace them you'll see that the tips get worn down, and wedge into place so that the black support plates cannot move out of the way of the stapler. The black plates look warped, but they aren't (I should say they always look like that).

They are fairly easy to get to. You do have to remove the finisher from the copier. Remove the front and rear covers. Open the right door. Pull the pins that retain the door. From there you'll see the arms. They can be changed with a little maneuvering.

2nd Choice) Clip overtight wire ties to the stapler rotation home position sensor.

3rd Choice) Shake down the stapler to its bottommost position (wherever it settles is fine). Adjust the flag that triggers the stapler home position sensor. If I remember correctly its the narrow **** in the flag.

Posted on Jan 28, 2009

  • 990 Answers

SOURCE: sharp ar 407

Hello sir;There have a procedure to reset;
1, press "program", "interupt", "clear", "interupt"
2, enter 14, then press start,then enter 0, press start again. then press clear.

Posted on Apr 28, 2009

  • 268 Answers

SOURCE: AR 5516S SHARP COPIER IS SHOWING F2 4O FAULT CODE

During installation , use sharp ar205 developer and sharp ar021 toner cartridge. This shows you did not use developer or used the wrong ones, good luck.

Posted on Mar 30, 2010

  • 109 Answers

SOURCE: AR 5516S SHARP COPIER IS SHOWING F2 4O FAULT CODE

toner type error

replace the toner cartridge

Posted on Apr 08, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My sharp machine ar 5516s is having problems giving error code l and 4 simulteniously what can i do


can be the main motor locked if its l4-01 but if its l4-31 its fusing fan locked detected or l4-35 its PS fan locked detected

Jun 18, 2014 | Sharp AR-275 Copier

1 Answer

My sharp machine ar 5516s is having problems giving error code l and 4 simulteniously what can i do


i hope its L4.If it is showing
L4 it means the main motor is locked(failing to move) Check all the moving parts including the drum unit, developer unit, main drive unit and fuser unit if they are moving freely. If they are moving freely change the main motor

Jun 18, 2014 | Sharp AR-5320 Black and White Copier

1 Answer

My sharp ar 5516s is showing error code L and 4 simultaniosly what can be the problem


Main motor lock,

Main-motor is unable to turn or has too much resistance, mlean main drive , and replace worn gears , if problem persists , check resistance on fuser-unit / developer-unit / OPC-unit

Jun 18, 2014 | Sharp Office Equipment & Supplies

1 Answer

Sharp AR5516 error code H4


Temperature error, use simulation mode 14 for reset the error , if not replace the thermistor, & use stabilizer to avoid problems due to power fluctuations.

Dec 04, 2012 | Sharp AR-5516s

2 Answers

The printer Ar-5516 is showing H4 error


this error means:
heat roller abnormally low temperature.
for check:
1- check the heater lamp
2- check the thermistor
for reset:
clear key --> interrupt key --> "0" key --> interrupt key --> 14 --> start key

Jul 04, 2012 | Sharp AR-5316 Advanced Digital Imager...

1 Answer

F2 40 error code on Sharp 5516s copier


you must use ar-202 developer.205sd used for 5516 or 5520

May 23, 2010 | Sharp AR-5320 Black and White Copier

2 Answers

AR 5516S SHARP COPIER IS SHOWING F2 4O FAULT CODE DURRING INSTALATION. WHAT COULD BE THE CAUSE. PLEASE.


During installation , use sharp ar205 developer and sharp ar021 toner cartridge. This shows you did not use developer or used the wrong ones, good luck.

Mar 12, 2010 | Sharp AR-5320 Black and White Copier

Not finding what you are looking for?
Sharp AR-5516s Logo

Related Topics:

36 people viewed this question

Ask a Question

Usually answered in minutes!

Top Sharp Office Equipment & Supplies Experts

Anthony Karuku

Level 2 Expert

268 Answers

amir hamza
amir hamza

Level 2 Expert

318 Answers

k24674

Level 3 Expert

8081 Answers

Are you a Sharp Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...