Question about Summit SPWD1800 Laundry : Washer/Dryer Combos

Open Question

Dryer will not work any more, keeps flashing error13 message

The dryer will start but no heat goes to the tub, instead the top of the machine gets hot and after 15 minutes the errormessage comes on and machine stops

Posted by Anonymous on

Ad

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

SOURCE: dryer proplem

Rather than try to give you answers, I'm giving you this online link that COULD lead you to a solution: http://appliantology.org/topic/42011-washer-dryer-combo-error-code-er13-haier-summit-ariston/
I looked at it for a few minutes and answers are up and down between encouragement and discouragement. One suggestion is a bad thermostat at the top of the unit, but I'm not sure if you'll be successful in locating replacement parts according to some of the things I glanced at. Hope this helps.

Posted on Jun 28, 2014

Ad
daimaxboyce
  • 282 Answers

SOURCE: dryer proplem

Do u want to resolve the f-13 fault code ON HOTPOINT WD860 Ultima
Fix the fault . It is a tricky job but the heater thermostat switch has tripped as it senses something burning. Probably a little bit of fluff on the heater element inside the heater unit.. There are 2 switches on top of this heater unit. One where the 2 blue wires go on the top left of the 3rd picture and the other which has a tall black wire connector on shown in the middle of the 3rd picture. Remove that connector and undo the holding screw . You can then reset the switch. The switch is a small circular switch hidden beneather the connector on the photos. This thermostat switch has a yellow. red dot ontop of it. If you use a small pin or needle and press into that dot you will hear it tick back into place. you have reset the switch now. You will probably need to clean the inside of the heater element unit to get rid of the fluff particles or it will keep switching off. To take this apart you will need a set of Star screwdrivers. Its a bit tricky but you will be able to undo the star screws and take them all out. I will add some photos to show you the unit apart. You can see the build up of fluff on the photos i have added from my hotpoint WD860 heater unit. This is a tricky job and takes about an hour due to the screw being awkward to take off and put on again but mine hasnt faulted for 2 years since sorting it out. You can buy a new Thermostat switch which is about 10 pounds sterling from Hotpoint or other spares stores.

Posted on Nov 15, 2014

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Dryer starts and about 5 minutes later stops and lights start flashing


DRYER OVERHEATING: Heating Element
A defective heating element can make a dryer too hot. If the element partially shorts out, it can produce heat all the time, regardless of whether the dryer is calling for heat. Remove the heating element to inspect it. The coils should not be touching each other or anything else.

Other Causes and Conditions
Air Flow Problem
Dryers need good ventilation to work properly. If the vent is clogged it can make the dryer too hot. Clean all of the vent tubing thoroughly.

Cycling Thermostat
Although not common, a defective cycling thermostat can make the dryer too hot. The cycling thermostat is supposed to turn on and off the heat to maintain the proper temperature. If the thermostat is defective it may keep the heat on too long. The thermostat is not adjustable or repairable, it must be replaced.

Felt Seal
Most dryers have a felt seal at the front and rear of the drum to keep the heat inside the drum. If the felt seal is worn away or missing, the dryer may keep heating and make the dryer too hot. This is not common.

Blower Wheel
A defective blower wheel will not spin properly and will not vent the hot air, making the dryer too hot. Check to see if there is adequate airflow out of the dryer.

Dryer runs then shuts down wont start up for an hour:
Bad motor windings


https://www.youtube.com/watch?v=3m5NZvY9V5Q

Mar 22, 2015 | Dryers

1 Answer

Haier HLP21E Top Load washer keeps beeping & blinking after water intake. It will rinse out the water when 'rinse' pressed. However it does not 'spin' but instead all three orange lights start blinking &...


No spin with alarm means the unit is out of balance.
The troubleshooting manual reads:
"The safety switch acts. The
spinning cannot work (The
WASH, RINSE and SPIN
indicator flash and alarm goes
off every 10 seconds). If
trouble cannot be solved after
alarming, it will alarm again
every few minutes."

To solve this the load must be balanced:

Make sure to level the machine on a solid floor. Also you may have to redistribute the clothing in the tub for even weight distribution.

Sep 28, 2013 | Haier HLP21E Top Load Washer

1 Answer

Overheats and keeps tripping dedicated breaker in house, venting and inside back panel vacuumed out.


If your dryer has a sensor it may have gone bad. Try using timed dry instead of auto dry.

I’m happy to assist further over the phone at https://www.6ya.com/expert/jaime_a0afdb97baa63a3d

Nov 09, 2012 | Dryers

2 Answers

Dryer is running but the dryer will not dry and the air is cold instead of hot


Hi,If you are having problems with your gas dryer not heatingthe most common problem is that the ignitor goes bad. Even though it glowssometimes it is still not working properly.if you dryer is gas check out this gas no heat tip....If you have an electric dryer, you can have many differentthings that can go wrong causing the dryer not to heat. check outthis electric no heat tip...

heatman101

Sep 13, 2011 | Frigidaire FGX831F Top Load Stacked Washer...

2 Answers

My drum won't turn everything else seems fine


Must be a broken belt. Unplug the dryer. Remove the filter.3a24c64.jpg Remove the screws to filter chute. Grab the rear of the dryer with your left hand and place a putty knife under the top to release the clips.08f0a6c.jpg Get the front off.. then get the tub out. 6608542.jpgGive it a good clean. The ribbed side of the belt goes to the tub. If you get it twisted it will break instantly. 9fe59c2.jpgffbef0a.jpg
I have a video which shows how to get into your machine, it has to do with a heating problem but the main thing is it shows how to get into the machine: Coil Replacement

Service manual and more HERE

Much more here

If you need further help, reach me via phone at https://www.6ya.com/expert/dan_73bbd84fe1d95b61

Oct 17, 2010 | Roper REX4634KQ Electric Dryer

1 Answer

Dryer will not keep constant heat


clean your vent that goes out side Thats what does that the hot air dosent go outside but comes back on the temperature control and shuts the heat off. Also if you put wet close it it the lint will be built up behind the fan. You have to lay the dryer down take the back off and fron the bottom on the left side is the vent foller the hoe to the left. there is four 5/16" screw hokling that tub on thake those screws out and raise that unit enough to get you hand to the fan blades and you will find two hands full of linte matted there.
clean that out dryer need good air flow be sure to pull youi vent out the top and clean before each dry.

Apr 21, 2010 | Whirlpool LGB6300 Gas Dryer

1 Answer

Even thuogh I made sure it was not on economy mode my hot tub will not heat up and the message board keeps flashing the word cool, do you know what could cause this?


it may be a bad temperature sensor or a bad heating element. Sounds more like a heating element. The cool should just be a warning or depending on the model, could mean that it thinks the water is too hot and is in "cool" mode trying to cool the water. Have the temp sensor and the heating element checked.

Feb 05, 2010 | Qca Spas Majestic Series Aruba Xl Hot Tub

1 Answer

Pump is running ever 5 minutes. The heat in the


Sounds as if the 'mode' for the tub is set to sense the temperature of the water. see if there is a setting on the control box to a 'timed' setting for filtering and heating instead of controlled by the temperature setting. the problem is the the control box is away from the water and when it calls for heat it is because the water is cooler there than in the hot tub. so when it calls for heat and the water starts to circulate it gets the hot water from the body of the hot tub and then shut down because it senses the 'hot water'. make sense?

Feb 23, 2009 | Blue Wave Aruba 15' Round 54" Resin Pool...

10 Answers

Beko tumble dryer not drying. drum goes round but it doesn't get hot. Model DRCS68


go into service mode and reset

to do this move to delicates turn on dryer and keep
pressed down cancel button for about ten seconds release
then all lights should flash when you press cancel again machine will go through test mode , then just turn machine off
it is now reset, this worked for min a drcs68w

Apr 23, 2008 | Beko DSV64W White Vented Tumble Dryer 6...

Not finding what you are looking for?
Summit SPWD1800 Laundry : Washer/Dryer Combos Logo

Related Topics:

67 people viewed this question

Ask a Question

Usually answered in minutes!

Top Summit Washing Machines Experts

ray gallant
ray gallant

Level 3 Expert

63731 Answers

 Russ Hill
Russ Hill

Level 3 Expert

4048 Answers

Bill Boyd

Level 3 Expert

53745 Answers

Are you a Summit Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...