Question about KitchenAid KSM150PS Artisan Series Stand Mixer

1 Answer

How to replace motor in kitchenaid artisan mixer

I replaced the worm gear but that wasnt the problem. My mixer will spin the beater but when anything is added to the bowl the beater quits mixing but the motor is still running. Guess the motor is worn out but im not sure

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • KitchenAid Master
  • 1,355 Answers

Sounds like a worm gear problem to me, it's impossible for the motor (armature) to move far enough to not drive the gear. There are driving pins in the system from fuse gear to paddle.
1) in the fuse gear
2) inside gearbox above planetary joining shaft to bevel gear
3) through planetary and shaft

There is also one joining the little gear inside the planetary to the shaft, doubt you'd break that one though.

Posted on Jul 18, 2014

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
  • 12 Answers

SOURCE: KitchenAid Mixer Squeaking

I would first get some canned air. Spray out the area around the Shaft. This is to make sure no harden food is up there. After that is clean spray some cooking spray "PAM"in the Shaft area. This should help. Good Luck

Posted on Feb 11, 2008

  • 145 Answers

SOURCE: Kitchenaid beater rubs bottom of the bowl

Your beater to bowl clearance has come out of alignment. This can happen naturally over time and with normal use of the appliance. This is something you may correct from home using a flathead screwdriver.

Unplug the mixer, with the bowl and flat beater removed. Tilt the mixing head back as far as the machine will allow. In the exposed hinge, behind where the bowl would normally sit, you will see a 3/8 screw exposed. Turn this screw half a turn counterclockwise (to your left) in order to raise the flat beater from the bottom of the bowl.

This may take a few attempts until the beater is clearing the bottom of the bowl again. If the adjustment screw will no longer turn, do not force it. It is only designed to move so far to make the appropriate adjustment.

Be cautious. Raising the flat beater too high may leave dry ingredients at the bottom of the bowl.

If further information is needed, I would advise you to contact Kitchenaid Customer Service. They may walk through this adjustment through you over the phone and can look into ordering replacement beaters for you also.

Their toll-free telephone number is 1-800-541-6390.

Posted on Jul 08, 2009

hslincoln
  • 235 Answers

SOURCE: Beater rubs bottom of mixing bowl.

JOE:You don’t say if you have a ‘tilt-head’or a ‘bowl-lift' mixer, but you can easily download a PDF version of your Owners Manual from the KA website (http://www.kitchenaid.com/flash.cmd?/#/page/home).Click on Customer Care>Locate Manuals& Guides> and enter the 6 character model number (in your case, use KSM90P)and select the last file listed that appear under Owners Manuals:KSM90PSWW0.pdf (2930.74 KB)and save that file to your PC.You’ll need to have Adobe Reader to be able to open it. Turn to Page 11 and you will find the instructions for adjusting the mixer head height.I have extracted the instructions below:
Beater to Bowl Clearance
Your mixer is adjusted at the factory so that the flat beaterjust clears the bottom of the bowl. If for any reason, the flat beater hits thebottom of the bowl or is too far away from the bowl, clearance

Tilt-Head models
• Unplug mixer.
• Lift motor head.
1aa320c.jpg
• Turn screw (A) SLIGHTLY counter clockwise (left) to raise flat beater or clockwise (right) to lower flat beater.
• Make adjustment with flat beater, so it just clears surface of bowl.
If you over adjust the screw, the bowl lock lever may not lock into place.


Bowl-Lift models
• Unplug mixer.
• Place bowl lift handle in down position.
9d33ad0.jpg
• Turn screw (B) SLIGHTLY counter clockwise (left) to raise flat beater and clockwise (right) to lower flat beater.
•Make adjustments with flat beater, so it just clears surface of bowl.

I hope this helps! –Howard, Burke, VA
If this solution has helped you, please rate it, thanks!.hslincoln

Posted on Nov 28, 2009

Testimonial: "Thanks to this answer, I was able to fix the problem in about five minutes. I am very grateful. Joe McCutchen"

  • 4 Answers

SOURCE: kitchenaid mixer makes a lot of noise. The beater

Hi - I've been searching for general info on KitchenAid stand mixers and ran across this so I'm throwing my $.02 in... Since KA stand mixer bases are essentially made of cast metal parts, there is a very slim chance that there is a lateral misalignment (side-side) unless it got dropped...eek! Sounds like a head height adjustment issue. Check out this from KitchenAid Conversations:

http://forum.kitchenaid.com/forums/topic.asp?TOPIC_ID=3032

Good luck.

DZII

Posted on Jan 03, 2010

Testimonial: "Thank you for your post. I will check out the suggestionsl"

  • 156 Answers

SOURCE: MY KITCHENAID MIXER MODEL # KSM5 TURNS ON BUT THE

The most common part to fail in this mixer is the worm gear:
http://kitchenaidmixerspares.co.uk/Home/tabid/36/p/Mixer-Part---Worm-Gear-and-Bracket-240309-2/ProductID/103/CategoryID/17/Default.aspx


Posted on Jan 24, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

When mixing cookie dough my kitchenaid mixer bogs down when the dough gets thicker .. replaced the brushes already and runs better but still bogs down .. does it need a new motor?


When using the dough hook the speed should be no higher than 2. That said, there is a limit as to how thick a dough the Artisan mixer can handle and you may well have reached that. Under these circumstances it is normal for the motor to slow down.

If the stress becomes too great, the worm (follower) gear will fail protecting the motor from burning out.

The Service Manual covering your model can be found at:

http://www.kitchenaidparts.eu/documents/pdf/service-manual/classic-svc-manual-new-email-version.pdf

Mar 05, 2017 | KitchenAid Food Mixers

1 Answer

How to check Artisan kitchenaid worm gear


If the planetary head (which holds the beater) is not reliably turning, you can be pretty sure that the worm gear (more properly called a worm follower gear) has protected the motor from burning out by sacrificing itself. The Service Manual may downloaded from:

http://www.kitchenaidparts.eu/documents/pdf/service-manual/classic-svc-manual-new-email-version.pdf

Jun 06, 2014 | KitchenAid Food Mixers

1 Answer

Speed problems with kitchenaid artisan mixer.


It sounds like two issues, the first is going to be the phase board, you will need to replace it, that should fix your speed issue.

The second issue will be a stripped gear, in that mixer there is a nylon gear that commonly goes bad, that would be the worm gear.

Here is a link to the phase board: http://www.mendingshed.com/kaphaseboard.html
Here is a link to the worm gear:
http://www.mendingshed.com/kawormgear.html

Also here is a link to the service manual: http://ep.yimg.com/ty/cdn/mendingshed/kitchenaidservicemanual.pdf

The service manual will show you how to take apart the mixer, and put it back together.

Jan 31, 2014 | KitchenAid Food Mixers

1 Answer

Kitchenaid Mixer Planetary becomes sluggish when met with resistance.


The problem will be with the worm gear, if the gear is not stripped then check that the locating pin for the worm gear is not broken or missing. Occasionally the plastic gear can detach from the aluminium boss between plastic and shaft. The worm gear is the 99.9% place where drive can slip. Afterthought, I suppose the planetary pin is not missing or broken??

Jun 28, 2013 | KitchenAid KSM150PS Artisan Series Stand...

1 Answer

Hi, I have a Kitchenaid stand up mixer custom edition 500 watt model #Kd2661xmc that sounds fine when I don't have anything in it, but sounds like its crying when I put just a single cake mix in it. ...


Get A Copy of the Repair Parts List for your model at Kitchenaid.com.
Remove the Gearcase Motor Housing (1) & the Transmission Housing (7)
Remove the 2 screws (23) holding down the Motor (2) and lift off way from
the Worm Gear (17). Test run the motor by itself at different speeds.
If it runs fine then it's time to inspect all the gears in the Transmission
Housing(7). Remove all the brown Grease covering the gears.
Pay attention in particular to the teeth of the Worm Follower Gear (19).
(the Bevel Gear (21) sits on top of this gear)
They should not be worn out or chipped. If they are then this is the source
of the noises you're hearing (the Worm Gear is grinding away the teeth of
the Worm Follower Gear). Once the Follower is replaced, your mixer will
be just as new again.
Please Note that this replacement is not an easy task. You need the right
tools and don't use a hard object like a steel screwdriver to pry out the
Planetary plate (15) from the beater shaft. Before re-assembly, use only
fresh new Food Grade Grease from Kitchenaid (the old grease may contain
metal filings from the worn out gear that will damage your new one)

Jul 22, 2011 | KitchenAid KSM150PS Artisan Series Stand...

1 Answer

Hi there, I was doing cake mixing and turn off


If you can hear the motor spinning and the beater does not spin, the worm gear has probably failed. These fail frequently, specially after using them beyond there designed limits. The motor heats up and the gear, which is a type of plastic or nylon, melts.

Feb 18, 2011 | KitchenAid KSM150PS Artisan Series Stand...

2 Answers

Beaters will not move


You have probably stripped a gear in the gear housing. Here is the breakdown of the gearbox:

http://shared.whirlpoolcorp.com/assets/pdfs/literature/Repair%20Part%20List%20-%208212010.pdf

The newer "more improved" mixers use plastic gears and they can't take the beating, no pun intended, and fail.

The good news is that the most likely gear to fail is cheap. Here it is on amazon.com:

http://www.amazon.com/KitchenAid-W10112253-Worm-Gear/dp/B0006HLAVA

http://www.misterfixit.com

Mar 25, 2010 | KitchenAid KSM150PS Artisan Series Stand...

Not finding what you are looking for?
KitchenAid KSM150PS Artisan Series Stand Mixer Logo

215 people viewed this question

Ask a Question

Usually answered in minutes!

Top KitchenAid Food Mixers Experts

Appliance engineer

Level 2 Expert

153 Answers

CJ C
CJ C

Level 2 Expert

66 Answers

Steve Allison
Steve Allison

Level 3 Expert

5569 Answers

Are you a KitchenAid Food Mixer Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...