Question about Zebra 105SL Thermal Label Printer

Open Question

Zebra 90 error keeps saying paper out - Zebra 105SL Thermal Label Printer

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
ozztech
  • 285 Answers

SOURCE: Zebra printer problem

chek on setings if the sennsor is reflective, transmissive or auto.
should be on Auto. try to read the Sensor profile, and check if read the gap.
Try the Manual calibration, and then run the sensor profile.
tur off and on again.

Posted on May 08, 2008

Ad
  • 21 Answers

SOURCE: My Zebra Zm 400 keeps saying Pause Error Condition

make sure that the maximum lenght for the label is set to something greater than the physical length of the label. I was having this issue with a 4x3 label. As soon as I increased the maximum lenght to 5 inches it worked.

Posted on Jan 08, 2010

  • 1 Answer

SOURCE: zebra lp2844 set up with paper with black

ihave 945 audio drivers . but no sound

Posted on Mar 10, 2010

ozztech
  • 285 Answers

SOURCE: my zebra printer wont line

run the sensor profile, check if check the gap, run manual calibration, if ask for reload media, please take 3 or 4 labels from the label rolar, put through the sensors (check if ribbon(if use) is install on the correct spots and don't stop the sensors to read the gaps) and run the manual calibration.

Posted on Nov 13, 2010

ozztech
  • 285 Answers

SOURCE: my printer says error condition paper out. But it

try to recalibrate media and sensors, run calibration, and run sensor profile, save, and restar again the printer. check if setings from the driver are correct or they can change the setings from the printer

Posted on Nov 13, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Zebra Z6m Error Paper Out


sensor not working or dirty in the feed path id suggest

Dec 27, 2017 | Zebra Z6M Plus Thermal Label Printer

1 Answer

I have a zebra 140Xilll printer that keeps displaying "out of paper" error but it has paper


Do a calibration from the panel and check that your paper remains under the sensors when printing.

May 18, 2011 | Zebra 140XiIII Plus Thermal Label Printer

1 Answer

My printer says error condition paper out. But it


try to recalibrate media and sensors, run calibration, and run sensor profile, save, and restar again the printer. check if setings from the driver are correct or they can change the setings from the printer

Apr 28, 2010 | Zebra Printer 140-751-00000

1 Answer

My Zebra Zm 400 keeps saying Pause Error Condition paper out however it is set to Direct Thermal. How do I get it back to the ready state?


make sure that the maximum lenght for the label is set to something greater than the physical length of the label. I was having this issue with a 4x3 label. As soon as I increased the maximum lenght to 5 inches it worked.

Dec 29, 2009 | Zebra 105SL Thermal Label Printer

3 Answers

Hello, my zebra ZM 400 keeps giving me the message of paper out/ribbon out I have replaced both rolls, powered down. Printer feeds one time, then keeps giving the same message


please kindly check the ribbon and label... make it sure that it fits exactly or properly or correctly fits the said consumables... if its not work check the settings...

Nov 17, 2009 | Zebra Z4Mplus Label Printer

1 Answer

Out of paper error in Zebra 110XiIII plus


There is a small thumb screw under the paper guide that has an adjustable stop to hold the paper. If you load it correctly, you should have one on each side to guide the paper into the printer. Also, the machine has either a roller or a bar to hang the labels on, correct? The bar has an adjustable stop to keep the roll from moving around while you print. You may want to setup the media sensor about 1 cm from the left of the printer to make it less subject to this type of error. They come from the factory very close to the edge of the paper to allow for some card printers to work well out of the box. Most people use labels and this is not necessary. I hope I have given you some helpful information.

May 06, 2009 | Zebra 110Xi III Plus Thermal Printer

1 Answer

Out of Paper Error


You get the error because the printer doesn't see any paper.
There are paper guides that need to be set for the size of the labels being printed. If you are switching from a 4" wide roll or sheet to a 3 1/2" label, you will have to move the slider in about 1/2". You will also have to calibrate the printer when you change label stock. If it won't calibrate, make sure the photoeye is hittint the break between labels. The photoeye is located where you insert the labels into the printhead path.

Feb 05, 2009 | Zebra Z4M Printer

1 Answer

Error printer zebra 220


Recalibrate. Sometimes the LED is too strong and it will show through the paper or the sensor is damaged. People will jam screwdrivers in there to get the label out. This sensor is found where the label first goes into the rollers.

Apr 25, 2008 | Zebra Printer 140-751-00000

Not finding what you are looking for?
Zebra 105SL Thermal Label Printer Logo

Related Topics:

118 people viewed this question

Ask a Question

Usually answered in minutes!

Top Zebra Office Equipment & Supplies Experts

Gateway information...

Level 2 Expert

252 Answers

Marvin
Marvin

Level 3 Expert

85160 Answers

Ekse

Level 3 Expert

13434 Answers

Are you a Zebra Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...