Question about Stanley Utility Knife

Open Question

How do I put utility knife 10-499 back together?

Posted by Anonymous on

Ad

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
  • 27 Answers

SOURCE: I cannot figure out how to put a blade in my

at the handel end it will pull apartthen slide the whats left of the old blade and put new won in its place just do it slowly so you dont forget how it goes

Posted on Apr 21, 2011

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I disassembled the Stanley 10 - 788 utility knife completely how do I put it back together


This utility knife reassemblies similar to the original. The only difference is this model uses two screws and that plastic insert. You will align the two metal halves and bring them together. Use care that the blade does not fall out of its holder and the little black plastic piece stays in place, near the blade. This may take a few tries. after you bring the two halves together you will carefully separate the bottom end (farthest from blade). Separate it just enough to slide the plastic insert into position. Once the three pieces align you will know. With little effort the two metal halves will close together. Install the two set screws and test for proper function. I'm including a Youtube video that shows how to properly change the blade and what it will look like after it is reassembled.
https://www.youtube.com/watch?v=5napTSRSyeQ

Sep 23, 2018 | Cutter Tools

1 Answer

How do i replace the blade on my utility knife?


loosen the screw that is holding the two casing halves together and separate the halves. pay attention to which way the old blade is in the compartment, remove it and put in a new blade in the same direction. close the casing and tighten the screw

Jan 16, 2013 | Cutter Tools

1 Answer

Can't close stanley fatmax


It only goes in one way, try to loosen the screw a little

Jul 30, 2012 | Stanley Fatmax Xtreme Retractable Utility...

1 Answer

I have a stanley fatmax knife but it doesn't have the small yellow button to help insert a new blade. what can I do?


HI!Kindly pull the button on the end of the knife and then after you remove that you can now put the blade of your knife.

Aug 21, 2011 | Stanley Utility Knife

1 Answer

I have a stanley FatMax. How do I insert the blade into the case?


On the side there is a big gold wheel, twist counter clockwise and the case should split in half, the blade is held by a magnet, prise the old blade off and replace with new one, then put case back together and tighten gold wheel clockwise
Goodluck!

Mar 06, 2011 | Stanley Fatmax Xtreme Retractable Utility...

1 Answer

Describe how you put a blade in FatMax model 10-778


The model in your picture is a fixed blade utility knife (model 10-816). Your question asks for instructions for model 10-778, which is a retractable knife. I'll guide you through the 10-778 which you asked for, if you need instructions for the pictured 10-816 please re-post the question.

Push the thumb slide forward as far as it goes exposing the blade. Press the blade change button on the side of the knife (the small button on the left side near the blade) and pull out the old blade.
Insert the new blade and slide thumb slide back to fully engage blade in the internal lock.

Dec 26, 2010 | Stanley Fatmax Xtreme Retractable Utility...

1 Answer

Cant put the thing back together after putting in new blade !!!fat max knife


some stanley knifes require stanley blades only, or make sure the clip blade is in is seated in the grove completely.

Dec 23, 2010 | Stanley Fatmax Xtreme Retractable Utility...

1 Answer

I unscrewed Stanley 10-379 Interlock retractable knife and now I don't know how to put back the gizmo that fell out or the three blades that came with it.


Google: how to change blade in Stanley 10-379 utility knife. Stanley website shows how knife & blade look on the outside. Put it together so it looks like that. Sorry, but ain't don't know how to send the picture to you.

Oct 21, 2010 | Garden

2 Answers

Stanley 10-777 utility knife: I need to reinsert the retractable blade slide back into the knife body. I try but the knife won't close.


I had the same trouble. The blade holder was out of the knife and would not go back in. I fixed it this way: open the screw knob all the way to the least tension. Slide the two parts open but not all the way- there is a tab on the blade holder that gets in the way if you try to drop it in at the fully open position. With the two halves SLIGHTLY open- slide the blade holder in making sure that the tab is seated in it's slot. Depress the thumb tab and bring it to the most forward position and the two halves should be able to be seated together again.

Oct 27, 2009 | Stanley Hand Tools

Not finding what you are looking for?
Stanley  Utility Knife  Logo

Related Topics:

1,286 people viewed this question

Ask a Question

Usually answered in minutes!

Top Stanley Cutter Tools Experts

JOHN LAPIER

Level 3 Expert

2591 Answers

Joseph Hoffmann

Level 3 Expert

1755 Answers

Joe Garcia
Joe Garcia

Level 2 Expert

206 Answers

Are you a Stanley Cutter Tool Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...