Question about Kenmore 73952 Gas Dryer

1 Answer

Igniter glows but no flame - Kenmore 73952 Gas Dryer

Posted by Anonymous on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 14 Answers

Could be your gas valve.

Posted on Jul 27, 2014

Ad

4 Suggested Answers

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

SOURCE: kenmore no flame

Is this the scenario? It lights for a few cycles or maybe not at all. The ignitor glows and goes out but no flame. Comes back on then does the same thing. If so it could be failing coils (those two black cylinders on top of the gas valve assembly). There's a kit that includes both and it's a fairly simple job.
33acd8f.jpg

Posted on Jan 03, 2008

Sal De

  • 2699 Answers

SOURCE: gas comes on and ignites first time and after up

bad gas coils located on top of the gas valve.when the coils are on there way out they will do this,when they heat up they fail,when the dryer and the coils cool down they will fire.they let the gas in and the ignitor ignites the flame after 15 to 30 minutes they fail.let me know how you make out

Posted on May 24, 2010

Macmarkus

Mark MacDonald

  • 2605 Answers

SOURCE: I have a kenmore gas dryer the igniter glows flame

Hello, welcome to FixYa.

I'll start by saying your post indicates it is obviously a Kenmore gas dryer, however if you could post the complete model number I can speak directly about possible remedies instead of generalizing.


At the risk of doing so, you mentioned you do get heat intermittently, and the drum does turn correct ?

If this is a symptom where the unit at first begins to heat but the flame drops out in a matter of seconds or minutes I would be looking at the burner coils. This is what you'll be looking for...

macmarkus_638.jpg
Once you've gain access to the coils you'll need to remove the wire harness and check the continuity.

Here's the tricky part though...many times they will ohm out ok when cool (not operating) yet as soon as there is current passing through the coil it "opens". The wire inside the coils is so fine that often it only takes a small current to "open" the circuit.

Most times it will only be one coil that fails but it is good practice to replace them both, many places used to sell them in a kit so double check with your supplier. I've attached a link here, though it may be different than your model the principles to changing the coils are the same.

As far as what part you may need and how to get it. There are a couple of places I prefer, on-line at "searspartsdirect.com" or "repairclinic.com".

Kit contains both the two wire and three wire solenoids. One solenoid is the primary and one is the safety. Both have to operate for the gas valve to open. Usually, one of them burns out as I said but you should always replace them as a set.

**unplug the appliance and turn off the gas supply before attempting any service...safety first**

The most common for Kenmore is part number 3479 at "repairclinic" as this link should provide you.

http://www.repairclinic.com/PartDetail/Gas-Valve-Solenoid-Set/3479
Let me know how you make out or if you require further assistance and I'll do whatever I can. Thank you for your patience while I was away for a while. Good luck.

Regards,

Macmarkus :)

Posted on May 25, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Hot surface igniter will glow and put out a flame but is not a blue/orange flame


First you need to get a nice blue steady flame to prove to the ignition module there is flame. Check you orifice and bypass tube.

Feb 22, 2014 | Lincoln Impinger 1116 Gas Oven

1 Answer

Gas dryer does not heat igniter glows red gas valve clicks but no flame


Hello,

Since the igniter glows i am wondering if within 1 minutes does it go off??or does the igniter just stay on??

If the igniter just stays on and doesnt go off the problem is going to the FLAME SENSOR

if the igniter goes off but no flame the problem will be the GAS VALVE COILS


GENE

Oct 12, 2011 | Dryers

1 Answer

I have an Amana Dryer Model # LGD20AW and when the dryer is first turned on the glow plug will heat up and ignite the gas but as the dry cycle continues the glow plug will heat up but no flame will ignite...


The glow coil or glow bar heats up and a sensor on the side reacts to the heat and then sends a signal to a gas valve.(solenoid valve) When the gas doesn't ignite when the coil is glowing... here are some reasons. 1. The sensor on the side of the burner assembly isn't working or sending power to the valve. 2. The valve is getting power but not opening. 3. The ignitor is not glowing hot enough to activate the flame sensor. Usually it is the sensor or the igniter not the valve.
Tom

Aug 10, 2010 | Amana Dryers

1 Answer

The electronic ignition on a gas water heater will not heat up and glow red to ignite the gas to heat the water atwood r/v water heater


You won't see any red glow until the burner ignites and burns for a while. Its only an ignitor and flame sensor, not a glow plug style.The ignitor has to provide spark for gas to ignite, then it also senses the flame and keeps gas flow coming. What exactly is happening when you turn it to on?

Jul 18, 2010 | RTO Atwood DSI-RV Water Heater-6 Gallon

1 Answer

I have a roper gas dryer model rdg4440sq0, the igniter glows then the flame lights. Then the flame goes out and doesn't light up again. When it cools down and i restart the dryer the igniter glows and...


If when the flame goes out ...Check to see that the igniter glows...If it glows and the gas does not light then replace the valve coils...Very common problem.....The coils are to weak to hold the valve open..

Apr 20, 2010 | Dryers

1 Answer

I hope that I can get this problem resolved. Can there be a thread started to help me through this? I will try to keep this as short as possible, I have a Ducane Mod. CMPB050C3A Nat. gas furnace. The...


say that you have the glow bar (Hot surface igniter) working
if the flame starts make sure you don't trash on the orifice of the burner, you can try to use a piece of wire or someting small to pick on the orifice of the burner, also make sure is not rust bewteen the burners gap where the flame spread to all the burners because if the flame sensor don't feel flame don't stay light up
hopes this help

Oct 09, 2009 | Heating & Cooling

1 Answer

Gas heater won't work


Which flame sensor did he replace? The pilot flame or the plenum temp. sensor.

Dec 14, 2008 | Carrier 38CKC036 Air Conditioner

Not finding what you are looking for?
Kenmore 73952 Gas Dryer Logo

Related Topics:

92 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kenmore Dryers Experts

Marvin
Marvin

Level 3 Expert

85206 Answers

jimorris77

Level 3 Expert

411 Answers

Brad Brown

Level 3 Expert

18110 Answers

Are you a Kenmore Dryer Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...