Question about Denon Audio Players & Recorders

1 Answer

Denon AVR-1513 Hello, I have a Denon AVR-1513 It starts up but when it goes to Cbl/Sat it shuts itself off and goes into protection mode i can't get further then Cbl/sat I even did the microprocessor reset and nothing any suggestions?

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 137 Answers

Disconnect speakers then try again if still shutting down you will have bad outputs.

Posted on Feb 19, 2015

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
marsrover
  • 682 Answers

SOURCE: I have a Harmon Kardon

please check all speaker cables for short circuit in receiver side or in the speaker side itself.

Posted on Jun 25, 2008

SOURCE: DENON AVR-1404 switch on problem

Maybe the audio amplifier IC´s are damaged that´s why go on the protection mode

Posted on Aug 22, 2008

  • 1 Answer

SOURCE: Denon AVR-1508 Receiver problems - cuts off and goes into protect mode

i have the same problem . denon had changed knob and circuits ?! one day later ... same issue !
i have 5.1 evo tangent 4-8ohms and 2 technics 8ohmsand i use frquently A+B configuration

Posted on Nov 08, 2008

mattvierra
  • 75 Answers

SOURCE: Denon receiver AVR-3300: Unstable source selection

Very important you have run system set up menu it configures your receiver with inputs analog or digital,speaker size,input,room correction etc Different input modes can be selected for the different input sources.
The selected input modes for the separate input sources are stored in
the memory.
q AUTO (auto mode)
In this mode, the types of signals being input to the digital and
analog input jacks for the selected input source are detected and
the program in the AVR-3300’s surround decoder is selected
automatically upon playback. This mode can be selected for all
input sources other than PHONO, MD/TAPE and TUNER.
The presence or absence of digital signals is detected, the signals
input to the digital input jacks are identified and decoding and
playback are performed automatically in DTS, Dolby Digital or PCM
(2 channel stereo) format. If no digital signal is being input, the
analog input jacks are selected.
w PCM (exclusive PCM signal playback mode)
Decoding and playback are only performed when PCM signals are
being input.
e DTS (exclusive DTS signal playback mode)
Decoding and playback are only performed when DTS signals are
being input.
r ANALOG (exclusive analog audio signal playback mode)
The signals input to the analog input jacks are decoded and played.
t EXT. IN (external decoder input jack selection mode)
The signals being input to the external decoder input jacks are
played without passing through the surround circuitry Your remote is searching for inputs because you did not properly run system set up!!! Here is a link to your manual [PDF] AVR-3300/1 3.3E*

Posted on Jul 22, 2009

  • 4234 Answers

SOURCE: HK AVR-247 protect mode

This is an indication of an internal problem. Typically this is shorted output transistors. Expect a parts cost in the $25-$40 range for this repair.

Dan

Posted on Apr 06, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I need help on how to set up my receiver AVR 1513


The owners manual can be found at many sites on the internet if you google for Denon AVR 1513. One site is amazon.com.

http://s3.amazonaws.com/szmanuals/d357e31200b1de2a76b2e5619ef9cdd8

Jul 07, 2014 | Denon AVR-1513 3D A/V Receiver - 5.1...

1 Answer

Denon avr2312ci shuts off and blinks red


Yes that is why. The receiver is protecting itself from an un-stable load impedance which causes current/voltage spikes through the final amplifier components and proportionally through the input where the protection relay is (click),. Do not continue using the amp until you have repaired or replaced the blown speakers. A rule of thumb is to maintain 8 ohms on each speaker wire plugged into the amp. Keep that in mind or eventually you will damage it.

Jan 23, 2014 | Denon AVR-2312CI

1 Answer

Avr 1513 no signal to subwoofer


Check its speaker connections. Check the speaker using a dry cell. If it is found OK, check the sound settings. If you wish to get more details, check this link.

Mar 22, 2013 | Denon AVR-1513

1 Answer

Denon avr-1513 shutting off and blinking red light


Sounds like you could have a bad speaker connection. Try disconnecting the speakers and see if it stays on. If so, connect one at at a time until it goes off to determine which one.

Jan 20, 2013 | Denon 5.1 Channel Receiver 1080p AVR-1513

1 Answer

Red power light blinking on my denon avr 1907, tried reset procedure, no speakers hooked up now and it still goes from green light to blinking red light and shuts off...Any clues?


This is a protection mode. The receiver protection circuit detects an internal problem like missing power supply voltage or blown channel and shuts down the receiver. You need to bring the unit to a repair facility.

Sep 26, 2011 | Denon AVR-1907 Receiver

1 Answer

I have a Denon AVR - 391 receiver and was wondering the best way to connect my CD player to as there is no provision for CD player


Sure it does:

http://www.retrevo.com/support/Denon-AVR-391-Receivers-manual/id/23705bh449/t/2/

Analog RCA cables go to anything available: DVD; SAT/CBL; DOCK
and/or
Digital audio goes to whatever is available: COAXIAL (SAT/CBL) or OPTICAL(TV)

Jan 09, 2011 | Denon AVR-787

1 Answer

Denon AVR-1604 too large front speakers blew the avr


Try disconnecting the speakers at the receiver. turn it on radio or any other source and turn up the volume. If the receiver still shuts of, there is an internal capacitor issue and needs serviced. More than likely though, it's a speaker problem. If the speakers were underpowered and at max volume, chances are the damage was to a voice coil in one of the speakers. If the receiver continues to stay on without being connected it's ok. check your speaker wires as well. Frequently loose braids on wires touch each other and create very little resistance until turned up, more volume, more resistance. Then the receiver puts itself into protection mode so no damage will occur. If you need further help, post a comment and I can help you troubleshoot further.

Aug 17, 2009 | Denon AVR-1604 Receiver

1 Answer

My denon avr-a10se stop working. When I start, aftr thr quick intiation the amp shuts itself and the red power light start to blinvk quickly - please help


This unit is in protect mode. This means that a problem was detected in the last stage of the amplifier section and the unit shuts down to prevent further damage. The most common failure parts are the output transistors. These usually run between $5-$15 each. Add in the local labor rate for the total repair cost.
Dan

May 20, 2008 | Denon Audio Players & Recorders

Not finding what you are looking for?
Audio Players & Recorders Logo

Related Topics:

246 people viewed this question

Ask a Question

Usually answered in minutes!

Top Denon Audio Players & Recorders Experts

 Grubhead
Grubhead

Level 3 Expert

5686 Answers

The Knight
The Knight

Level 3 Expert

76115 Answers

Marvin
Marvin

Level 3 Expert

85161 Answers

Are you a Denon Audio Player and Recorder Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...