Question about Sewing Machines

1 Answer

My needle bar fell off my designer ruby

How can I put my needle bar back on my machine? it has come off.

Posted by Anonymous on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    New Friend:

    An expert that has 1 follower.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 72 Answers

If the needle bar has come off, you need to take your machine in for service. This needs to be corrected by a technician. Particularly for a Husqvarna Viking machine which has a very specific warranty.

Posted on Aug 27, 2014

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
mohammed387
  • 1952 Answers

SOURCE: My needle broke and a piece of metal fell out of machine

just adjust to needle in fix to strait in needle clamp hole it operate to needle strait to hole so needle do nt break but needle is best buy qualtity

Posted on Aug 31, 2008

  • 1 Answer

SOURCE: My needle broke and a piece of metal fell out of machine

Totally happened to me last week. I discovered that the metal piece that fell off and holds the needle has a small screw that holds it in place. It needs an Allen wrench (tiny one) to tighten it back into place. I just lucked into figuring it out.

Posted on Feb 17, 2009

  • 52 Answers

SOURCE: Needle holder fell off of machine

there should be an allen screw on the back side of the needle bar clamp push it up and on and make sure its as stright as you can get it and tighten down on the allen screw

Posted on Jul 14, 2009

  • 2 Answers

SOURCE: brother sewing machine model XL-6562.needle holder came off rod.n

The needle holder has a screw right above the screw that holds the needle in place. It really doesn't look like a screw because it does not appear to have a slot for a screwdriver. However, with a small flat head screw driver you can tighten it up. There is also a curverd wire that must be inserted into a slot at the bottom of the holder. The screw tightens against the wire that tightens against the post. (It's a curved wire that curves around the front part).

Posted on Aug 20, 2009

  • 1 Answer

SOURCE: I need a manual for a White 2200 multi- tasker sewing machine.

You need to take this to a repair person.
I do have a manual but you can go to www.whitesewing.com and get one. Also the tension is a big problem if you don't use the exact bobbin. I was told that most bobbins will work in this machine but it turns out that only the one that comes with the machine really works. I would look for the parts to your machine. Sometimes they get lost in your sewing kit.

Posted on Nov 15, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Viking ruby needle bar is not straight but at an angle


Again, this is a service issue and needs to be looked at by a authorized service person for Husqvarna Viking. It should be covered under warranty, unless it was user abuse.

Aug 26, 2014 | Sewing Machines

3 Answers

My needle broke and a piece of metal fell out of machine


just adjust to needle in fix to strait in needle clamp hole it operate to needle strait to hole so needle do nt break but needle is best buy qualtity

Aug 31, 2008 | Brother XR-65t Mechanical Sewing Machine

1 Answer

Problem with needle bar/holder on viking ruby


Again, this is a defiante issue and needs to be looked at by an authorized Husqvarna Viking service techinicain.

Aug 26, 2014 | Sewing Machines

1 Answer

I have a new designer ruby and the needle keeps braking


If your machine is brand new, take it in and exchange it immediately. You got a lemon.

Mar 19, 2013 | Sewing Machines

2 Answers

I have a Brother XR-65. The needle bar fell out as I was sewing. I need a repair manual or some instruction on how to secure the needle bar in the machine. I have the bar itself and a pin sized piece of...


This was happening to me also - you have to tighten a different screw than the one that holds the needle in.

http://www.sewingpartsonline.com/needle-clamp-screw-brother-ls-2125-sewing-machine.aspx

My husband thought the screw was missing - it is actually a plastic screw with a hole in it for a tiny allen wrench.

You can see it in this picture also

http://www.sewingpartsonline.com/needle-clamp-babylock-brother-xz0001051.aspx

If you look at the photo of the screw I attached, you can zoom in and see it has a hexagonal hole.

It is above the flat head needle clamp screw (the one that holds the needle in)

It is REALLY annoying that this screw is mentioned nowhere in the manual, and the hex allen wrench is not included with the machine.

Kind of an important little detail, considering it holds the needle assembly together... you'd think that they would have told you about it.

Sep 09, 2011 | Brother Sewing Machines

2 Answers

The needle on my sewing machine literally just fell off. Not kidding. I'm holding an unbent and otherwise pristine needle. Oh brother SE-270D! I'm not sure how to put the needle back in. I think it just...


when you put the needle in the needle clamp holder the flat side of the needle goes toward the back of the the machine when you tighten the needle clamp screw make sure it's holding the needle,,make sure you can't pull the needle back out of the clamp,, if you can something is wrong with the needle clamp or the screw

Dec 06, 2010 | Brother SE-270D Computerized Sewing...

1 Answer

Needle clamp fell off needle bar


Screw it back in after replacing the needle.

Aug 01, 2009 | Brother XL-5130 Mechanical Sewing Machine

3 Answers

Needle holder fell off of machine


there should be an allen screw on the back side of the needle bar clamp push it up and on and make sure its as stright as you can get it and tighten down on the allen screw

Jul 08, 2009 | Brother XL-6562 Mechanical Sewing Machine

2 Answers

My needle broke and a piece of metal fell out of machine


this sounds like the needle guard it is usually held on by the same screw that holds the needle clamp it should fit so that it comes across the needle at the front to stop your fingers being sown but not interfere with the needle try turning by hand before turning back on.

Jun 05, 2009 | Brother XR-65t Mechanical Sewing Machine

2 Answers

My needle broke and a piece of metal fell out of machine


Totally happened to me last week. I discovered that the metal piece that fell off and holds the needle has a small screw that holds it in place. It needs an Allen wrench (tiny one) to tighten it back into place. I just lucked into figuring it out.

Sep 11, 2007 | Brother XR-65t Mechanical Sewing Machine

Not finding what you are looking for?
Sewing Machines Logo

Related Topics:

49 people viewed this question

Ask a Question

Usually answered in minutes!

Top Sewing Machines Experts

Tally Girl
Tally Girl

Level 3 Expert

1134 Answers

Chris Wetmore

Level 2 Expert

188 Answers

Marvin
Marvin

Level 3 Expert

85206 Answers

Are you a Sewing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...