Question about Whirlpool Ultimate Care II LSQ9549L Top Load Washer

Open Question

Loud cluck evey 5 seconds during spin cycle on my whirpool top load washer

Replaced the coupler and still loud clunk and whiring gear noise.

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Anonymous

  • 249 Answers

SOURCE: Loud Noise during spin cycle

drum bearings are gone,it would cost too much to repair,the drum shaft would to be repalced as well.Sorry

Posted on Dec 17, 2007

Ad
Coldcut

Karl Whisenand

  • 1554 Answers

SOURCE: Whirlpool LHW0050PQ Front Loading Washer VERY NOISY during spin cycle

remove the top access panel 3 screws in top rear.
now look around and push on the drum from top
it has suspension shocks and springs like your car they should resist any movements.
look/wiggle the concrete balance blocks , no cracks or loose.
inside the tub are the arm solid /not loose.
run it with the top open what do you see/hear and where
look under the rubber flap in front did anything get under the tub

Posted on Mar 04, 2008

robocop

Bill Batross

  • 90 Answers

SOURCE: Whirpool lsq9244eqo fills and drains but does not spin or agitate

It sounds like the agitator gripping teeth are worn out. To check this, take the agitator cap off with a strong knife or flat-head screw driver, pull the cap off and check the plastice teeth and four plastic hooks that grab the teeth. If they are worn out, then you will have to replace the agitator. To replace it, you will see a nut that is between the circlular teeth. Unscrew the nut and pull the agitator up hard.

Posted on Jan 19, 2009

the_admiral6

Steve Barrington

  • 14 Answers

SOURCE: Washer drum shakes excessively during fast spin

y shaped piece that contains the spindle that attatches to the basket and allows it to spin is corroded and cracking. you can't buy just the spindle bracket, you must buy the basket too. you'll be buying the front part of the drum too, if you wait to long.

Posted on Mar 07, 2009

Michael Childers

  • 240 Answers

SOURCE: washer sounds like off balance during spin

old duets have nut on rear pulley that becomes loose. remove rear panel and tighten nut. check while spinning by hand if pop is felt. if it rotates smoothly then you may need new shocks on tub

Posted on Mar 14, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Washer makes loud clunking noise after spin


No that would not be your problem. I assume this is a direct drive system and if it is did you check the motor coupler although what you are describing it sounds like your gear case is going bad. Good Luck!

Jun 02, 2015 | Whirlpool LSQ9549P Top Load Washer

1 Answer

99 Grand Cherokee. Started with locking or binding with loud clunks. After long drive, rear diff was smoking and was replaced. Just drove it and after shifting into all time 4wd and then back to 2wd did it...


Sounds like a bad transfer case. Generally what you experienced is caused by a tire mis-match but can also happen by itself sometimes. GC's use a fluid coupler that is supposed to engage 4wd when tires begin to slip. (coupler is pretty much the same as the mechanical clutch unit on your fan, only larger) If the coupler fails, symptoms like yours happen.

Mar 27, 2011 | 1999 Jeep Grand Cherokee

2 Answers

Loud Clunking when jeep starts moving in drive.


may be the gears in the rear end or check your motor mounts, ive had the noise and it was motor mounts

Dec 06, 2009 | Jeep CJ7 Cars & Trucks

1 Answer

I have a Kenmore series 80 washer that is making a loud clunking


check the motor coupler between the gearcase and motor for wear. If it is cracked or broken it will need to be replaced

Jan 04, 2009 | Kenmore 24032\24036 Top Load Washer

1 Answer

Kenmore 90 series loud whirring/howling noise during spin cycle


Sounds like you have a broken motor coupler. They are inexpensive. Can be a little tough to replace but I can walk you through it. You can purchase a coupler here.
http://www.shop.washermd.com/product.sc?categoryId=1&productId=1
Dave

Dec 18, 2008 | GE WBSR3140DW Top Load Washer

1 Answer

Clunking and grinding noise


My 2003 F150 Supercrew would not engage in 4x4, it ended up being the shifting fork in the front end, cost me $200.

Jul 16, 2008 | 2005 Ford F-150

1 Answer

When replacing direct motor coupler not enough?


Gear case part # 3360629 retails for about $170.
This dosn't happen very often.
You can find a junk whirlpool, roper, kenmore or kitchen-aid and pull the motor and gear case to save $$$$$

Jan 22, 2008 | KitchenAid KAWS850LE Top Load Washer

2 Answers

Transmission making loud clunking noise


sounds like your torque converter.

Nov 23, 2007 | Computers & Internet

Not finding what you are looking for?
Whirlpool Ultimate Care II LSQ9549L Top Load Washer Logo

Related Topics:

111 people viewed this question

Ask a Question

Usually answered in minutes!

Top Whirlpool Washing Machines Experts

Marvin
Marvin

Level 3 Expert

85206 Answers

Gerry Harvey
Gerry Harvey

Level 3 Expert

1481 Answers

jimorris77

Level 3 Expert

411 Answers

Are you a Whirlpool Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...