Question about Whirlpool Ultimate Care II LSQ9549L Top Load Washer

Open Question

My ultima washer drum will not turn

Put my washer on 95 wash and it done the wash but it did not spin it drained the drum will not move when i try to spin it round

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
  • 1 Answer

SOURCE: UL Code

Solved the unbalanced problem - open the top of the machine (press in with a flat putty knife about 3" in on the front on each side while lifting up as there are 2- 1" wide catches). Once both sides are unlatched, raise the lid then slightly lift the rear of the lid so that it fits into the curved part at the top of the hinges then open all the way - tape the lid to the top so it doesn't flap about and scotch the lid to keep it from falling back down on you. Now, look around - see all that rust?  The rust has fallen into and gotten underneath one or more of the 4 white plastic suspension "ball joints" which have probably totally dried out by now from their factory grease because of the water, bleach, and rust particles.  Having someone help you, simply lift up on one of the 4 corner suspension rods - gravity and weight is all that holds them down. The white ball will lift out of the socket and still be attached to the rod. Clean out the rust, lightly sand the "socket" with emery cloth, then slop in a fingerful of grease. I used automotive wheel bearing grease with graphite in it. Also scrub off all embedded rust on the white plastic ball. Lower that corner back into the newly cleaned and greased socket and repeat for the other 3 corners. Now when you move the tub around notice how the balls pivot in their sockets like they are supposed to. When they were dry and rusty they wouldn't move enough to allow the tub to twist like it should so it slammed around.  Now, shake your head in disgust that after only 2 years there is so much rust that you wonder if it will make it another year before falling apart, close the lid, and try another load.  That totally solved my off-balance problem where even a single handkerchief would give the UL error. It is still a finicky machine, but at least once again works like it did when new.

Posted on Jan 06, 2009

Ad
  • 68 Answers

SOURCE: my washer will not spin and drain

The load was probably unbalanced enough to trip the safety and shut the machine down. Have you tried running it again empty since then?

Posted on Nov 15, 2009

  • 714 Answers

SOURCE: clothes are soaking wet after washer is done

maybe your clutch is slipping not getting full spin speed,,,,or could be a problem with your basket drive assy

Posted on Feb 21, 2010

Testimonial: "thought it might be something simple like changing out a switch. Looks like we need a tech house call. Thanks"

beltronic205
  • 1481 Answers

SOURCE: Standing water in the washer hours after wash cycle completes

YES..I think drain hose @ sink too low Waste water from sink entering machine...Raise pipe....tie up ....

Posted on Apr 09, 2010

Macmarkus
  • 2605 Answers

SOURCE: drum is not moving

Hello, I have a couple of question before we can provide a diagnosis and ultimately a solution. Does it rotate in either direction for the wash cycle ? Does it spin if placed in just the spin cycle ? Would it be possible to provide a model number and maybe confirm it's a Bosch washer ? I will try and be helpful, but I'll need a little more detail. I look forward to seeing your reply. Macmarkus :)

Posted on Apr 11, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Hotpoint ultima washing machine wma74 drum not turning


If the machine wasn't excessively noisy before and when you select spin only you can't hear the motor running its likely to be the carbon brushes in the motor worn down till they no longer contact stick a new set in if the carbon length sticking out the brass holder is less than around half an inch long

Dec 08, 2013 | Hotpoint Ultima WF860 Front Load Washer

1 Answer

Washing machine motor not turning


hello,

what this indicate is that there have been a power disconnection from power supply on the jet string connected to the drum (drum controller)

what you will have to do to solve this problem is to unscrew the the washer then trace the wire down to the jet it is round in shape at the back of the washer
please rate this
thank you

Jul 05, 2010 | Hotpoint Ultima WF860 Front Load Washer

3 Answers

My Hotpoint Ultima WMD 960 displays "F04" on the display panel before the programme ends. Have cleaned the filter and it worked OK in spin mode and finished normally but now have put in a washing load, it...


Error code F04 means pressure switch jammed on empty.
Do the following.
Remove lower rear panel of washer.
Remove large black hose on bottom of drum.
Remove and clean filter inside the hose.
Remove the hose on to the pump, and check for blockage or obstruction here as well.
Please rate my solution.
Thankyou.

Jan 25, 2010 | Hotpoint Ultima WF860 Front Load Washer

1 Answer

My hotpoint ultima wont spin, its as thought something is preventing it for spinning. When its switched to spin cycle it turns a little to the left, then a little to the right, but cant seem to go any...


Things that couse this are, worn motor brushes, unplug remove the top, the motor should be at the top, if so remove the wire attached to the spade of the grey cartridge then unclip using a very thin screwdriver pushed down the back of the cartridge, and slide out if there is only a small peice of brush showing they must be changed, if ok spin the drum by hand if it moves freely the the drum is ok, the last thing to check is if it moves through the wash, but its just the spin that it wont move, there is a blockage, and the preassure vessel wont allow it to spin.

Jul 10, 2009 | Hotpoint Ultima WD72 Front Load...

2 Answers

Drum wont move


Check the motor and the belt on the back of the unit behind the rear plate. Make sure that the belt is attached and the motor is spinning. If this helped please rate. Thank you

Feb 12, 2009 | Hotpoint Ultima WF860 Front Load Washer

1 Answer

Ultima 1000 wont spin


there may be a blockage at the pump end of the drain hose or the filter.

Jan 21, 2009 | Hotpoint Ultima WF860 Front Load Washer

1 Answer

Washing machine won't spin


Do you hear the motor spinning loud whirring noise,when drum is not,if so drum belt has come off or snapped,if no noise possible brushes on motor need replacing

Jan 18, 2009 | Hotpoint Ultima WD72 Front Load...

1 Answer

Washine machine won't turn last spin.


If it has a Start-Reset button, try pressing and holding for 3 seconds..
Select a drain and spin prog and try again
Plz rate my suggestion.
Thanks.

Dec 26, 2008 | Hotpoint Aquarius WF000 Front Load Washer

1 Answer

How do I replace the belt that makes the drum spin on a Hotpoint Ultima WF860 ?


The belt goes around the drum and onto the motor pulley. No need to loosen anything. Put tension on the belt and fit it onto the motor pulley by gently turning the motor and pushing the belt onto the pulley at the same time.

Oct 28, 2007 | Hotpoint Ultima WF860 Front Load Washer

Not finding what you are looking for?
Whirlpool Ultimate Care II LSQ9549L Top Load Washer Logo

Related Topics:

100 people viewed this question

Ask a Question

Usually answered in minutes!

Top Whirlpool Washing Machines Experts

Marvin
Marvin

Level 3 Expert

85206 Answers

Gerry Harvey
Gerry Harvey

Level 3 Expert

1481 Answers

jimorris77

Level 3 Expert

411 Answers

Are you a Whirlpool Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...