Question about Uniden DECT 1480-3 Black Cordless Phone w/ 3 Handsets DECT 6.0, Answering Machine, Caller ID

1 Answer

THE BASE SET OF MY UNIDEN 1480-3 CORDLESS PHONE NO LONGER BEEPS WHEN I HAVE A NEW MESSAGE. CAN ANYONE HELP?

All numbers that are shown in handset are as follows: DECT 1480-3 128E0311 IC 513C-UN107 REN 0.0 BM20352280

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Uniden Master
  • 5,746 Answers

You can set or change the answering system options from any handset.
Open the menu and select Ans setup then select Message alert and activate it!

Beeps will be on!

Posted on Oct 05, 2014

Ad

6 Suggested Answers

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Anonymous

  • 39 Answers

SOURCE: uniden 5.8Ghz phone.

You need to reset the main base unit. Unplug the power from the back of the base. While the power is disconnected, press and hold the delete key while reconnecting the power. Wait for a long beep tone. When the display shows 88 or P, press play button one time. If you have a phone without an answering machine, disconnect the power from the back of the base, press and hold find hs button while reconnecting power.

Posted on Mar 17, 2009

Anonymous

  • 2 Answers

SOURCE: ADDING HANDSET SAYS OUT OF RANGE

A search of Uniden support only said to call 1-800-297-1023 with handset registration issues. The rep picked up quickly and walked me through the reset procedure. Here it is step-by-step:

1. Remove battery
2. Hold down the * and # buttons and reinsert battery. You should hear a long beep. If not retry. (This is a bit awkward but hold the handset upside down and it's workable)
3. Screen will be blank. Immediately press the right soft menu button.
4. Screen will report that EEPROM is clearing and then state EEPROM Clear Ok
5. Remove battery (yes again)
6. Reinsert battery (this time there's no need to hold down any buttons)
7. Handset will reboot with Welcome screen and then state that phone must be registered (this is the status a handset should be in from the factory)
8. Place handset on base and it will register as normal

Posted on Oct 09, 2009

michelletrip

Michelle Tripp

  • 1 Answer

SOURCE: I have a Uniden DECT 1480-5c phone (base 5

have this EXACT same problem---could it be my wireless router interfering??

Posted on Sep 26, 2010

nonontech

Lebanon Raingam

  • 4737 Answers

SOURCE: I'm looking to download

Hi!, Welcome to FixYa. There is no specific manual for this Model, but there's a manual for Uniden Dect 1480 series for all 1480 series phones (which are actually similar but come with different number of sets). To read it online, please click HERE, and to download, please follow this LINK. They are in pdf format, you'll need a pdf reader to open the manual on your computer. If you don't have a pdf reader like Adobe Reader, please follow this LINK and download it.
About your handset, I am afraid, it would work, unless it is also a 1480 series cordless.
Good Luck.
Thanks for using FixYa.

Posted on Jul 26, 2011

Dave

  • 1 Answer

SOURCE: I bought 2 sets of

Deregistering Handsets.
Press & hold the "END" & then the " # " Key. Continue to hold the two keys until a menu comes up. Select "Deregister Handset". When it asks which handset, select the handset number that you are using.

To register a handset, simply place the handset in the main base unit. You'll the main ans mach bases on for both sets to do this.

Posted on Jan 08, 2013

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

DECT 1480-4 Uniden Corless phone- how do you get rid of red LED lite ?


Do you mean the status light on the handset or the one on the base? The status light on the base will be on if the answering system is on. The handset status light will be on but steady when the handset is on the charger. (It's a battery charging indicator in that case; take the handset off the charger to stop the charging system. It provides a trickle charge to offset the battery discharging over time) The light blinks to indicate new messages are available on the answering system. Press the Play button on the base or the Messages/Mute button on the handset to play new messages.

Uniden offers the manuals for many of their phones on their support site: http://www.uniden.com/bin/venda?ex=co_disp-view&bsref=uniden&scat=dectphones_mnl . The direct link to the manual for the DECT-1480 is http://www.uniden.com/content/ebiz/uniden/resources/ownersmanuals/DECT1480-2om.pdf .

I hope this helps.

Cindy Wells

Dec 02, 2011 | Lands Phones

1 Answer

I need a manual for Uniden 1480-5A cordless phoneset with answering machine, how can I obtain one?.


You can download manuals from Uniden's site. Here's the 1480-4A manual, which is the same base with 4 handsets.

Jun 23, 2011 | Uniden DECT 6.0 Cordless Telephone...

2 Answers

How do i set the answering system on a uniden 1580-3 phone, mine is just background noise on the answering machine when someone calls in to leave a message


Here is the manual for your phone. You can download the manual and the instructions for setting up your answering machine are on page 43:

http://www.uniden.com/pdf/DECT1580-3om.pdf

Setting Up the Answering System
You can set up your answering system's features from the handset. Only one handset at a time can access the answering system menus.

Note: If you have multiple bases, select the base with answering system you want to access (see page 15).

Recording a Personal Greeting
Your answering system comes with a pre-recorded outgoing message or greeting that plays when you receive a call: "Hello, no one is available to take your call. Please leave a message after the tone." You can record your own personal outgoing greeting. Your recorded greeting must be between two seconds and thirty seconds long.

Press /mute. The system announces the number of new and old messages, then starts to play the messages unless it has no messages.

Press 5 to stop the announcements or message playback. You will hear intermittent beeps indicating that the system is in the command waiting mode.

Press 8 to start the recording. The system announces, "Record greeting." Begin recording after the announcement.

When you finish recording, press 8 again or press 5. You will hear a confirmation tone, and your recorded greeting plays back for you.

Selecting a Greeting

Once you have recorded a personal greeting, the phone automatically switches to your personal greeting. You can
also switch back and forth between the pre-recorded greeting and your own greeting at any time.

Press /mute. The system announces the number of new and old messages, then starts to play the messages unless it has no messages.

Press 5 to stop the announcements or message playback. You will hear intermittent beeps indicating that the system is in the command waiting mode.

Press 6. The system plays the current greeting.

Jun 15, 2011 | Uniden 5.8GHz Expandable Cordless Phone...

1 Answer

I need a manual for Uniden DECT 6.0 product name DECT 1480-8 model # BM 40092294


The manual is the same for all DECT1480 phones; the digit after the dash indicates the number of handsets that came with the phone initially.

The English version of the manual for the DECT 1480 is here http://www.uniden.com/pdf/DECT1480-3om.pdf . This is a 2 accessory handset version. A complete list of the available Uniden DECT cordless phone manuals is here: http://www.uniden.com/index/manuals_results.cfm?cat=59 .

I hope this helps.

Cindy Wells

Jun 04, 2011 | Uniden Cell Phones

1 Answer

Setting up my outgoing message: just purchased Uniden cordless DECT 1580. Manual says select command 8. How do I find Command 8? thanks, joan


Hi,

please follow the instruction to register the handset to base

To register a DCX150 accessory handset:
1. Charge the handset completely.
2.Place the handset in the base cradle for about thirty seconds. Handset Registering will appear in the LCD.
3.When the handset has registered to the base, the LCD will display Registration complete then show the handset ID number.

If the display shows Registration failed, repeat the process again.

To register a DCX200 or DCX300 accessory handset:

1.Charge the handset completely.
2.Disconnect the base AC adapter. Then press and hold find while you reconnect the adapter. Keep holding find until the charge LED starts to blink.
3.On the handset, press and hold # until the handset beeps and displays Handset Registering.
4.When the handset has registered to the base, the LCD will display Registration complete then show the handset
ID number.

If the display shows Registration failed, repeat the process again.

Thanx

Jul 21, 2010 | Uniden Cordless Phone

1 Answer

Uniden 6.0 answer/base/ cord less message set up


Hi,

Thanks for using FixYa.

Please let us know the complete model number of the phone.

May 15, 2010 | Uniden DECT 6.0 Cordless Telephone...

1 Answer

Handsets do not register


Press the END button to exit or erase the message. Press Menu/Select. Scroll uo or down to find Register Base. Select the option, select it and put the handset in the charging cradle of the base. A confirmation beep will sound.

Jan 11, 2010 | Uniden DECT 6.0 Cordless Telephone...

1 Answer

My cordless phone says "to register see owners manual for help" How do I get the phone working, it is a uniden DECT 6.0 Model DECT 1588-2


With the phone in standby, press MENU/SELECT on the base.
Move the cursor to select the Register Handset menu, and then press MENU/SELECT. Handset Registering will appear.
On the handset, press and hold # until the handset beeps and displays Handset Registering.
When the handset has registered to the base, the LCD will display Registration Complete then show the handset ID number.
If the display shows Registration failed, repeat the process again.
Note: If a handset has ever been registered to a base, reset the handset before you register it to a new base

Dec 21, 2009 | Uniden DECT 6.0 Cordless Telephone...

2 Answers

How to clear all registrations from the base


One has to completely deregister all handset by pressing end and # keys together till complete de registration is shown on handset screen. if the de registration is not done as above stated method the hand set will not register will show connecting on hand set screen.

Jul 16, 2008 | Uniden TRU8885-2 Cordless Phone

2 Answers

Uniden 5.8Ghz phone.


You need to reset the main base unit. Unplug the power from the back of the base. While the power is disconnected, press and hold the delete key while reconnecting the power. Wait for a long beep tone. When the display shows 88 or P, press play button one time. If you have a phone without an answering machine, disconnect the power from the back of the base, press and hold find hs button while reconnecting power.

Jan 20, 2008 | Uniden Cordless Phone

Not finding what you are looking for?
Uniden DECT 1480-3 Black Cordless Phone w/ 3 Handsets DECT 6.0, Answering Machine, Caller ID Logo

191 people viewed this question

Ask a Question

Usually answered in minutes!

Top Uniden Lands Phones Experts

k24674

Level 3 Expert

8081 Answers

Cindy Wells

Level 3 Expert

6046 Answers

Marvin
Marvin

Level 3 Expert

85206 Answers

Are you an Uniden Lands Phone Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...