Question about Nostalgia Electrics Kitchen Appliances - Others

Open Question

Where can I purchase parts for my nostalgia electrics buffet, I need pans

I need the pans

Posted by on


3 Suggested Answers


6ya staff

  • 2 Answers


Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017


Korede Atunrase

  • 1456 Answers

SOURCE: I need to get the metal popcorn popping pan for a


I will advice that you buy online visit or any other online super-mart by searching through Google.

Posted on Aug 04, 2010


SOURCE: I have a three station

Hi, I believe that one can have the coating stripped off, and re-applied, however it would be expensive. If you wish to pursue this avenue then have a search on the 'net for suppliers that can do the task.
Otherwise contact the manufacturer and they maybe able to assist you. link below.

Posted on Feb 24, 2011

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

How to replace a oil pan gasket 2004 nissan xterra

are you referring to the lower sub pan or main oil pan? the lower sub pan on most nissan engines are fairly easy to diy. just unbolt all the fastening bolts and you would need a pry bar or screwdriver to pry off pan. remove the old liquid gasket on pan and on main pan mating surface and reapply liquid gasket. reinstall lower sub pan and install fastening bolt.
if you are referring to the engines main oil pan its a more extensive repair. you would need the correct tools and equipment such as trans jack and engine support holder.

Oct 11, 2014 | Cars & Trucks

1 Answer

How to change oil pan 1995 GMC vandura3500

I am guessing this is just like all vehicles and the oil pan is directly underneath the engine. You will need to buy a a new oil pan gasket and if you are replacing the pan, another pan. Take the bolts off the pan making sure that you allow the oil to drain out into a waste container. Once you get all the oil out, you can take the pan off. Scrape off any old gasket parts that might have stuck on the engine. Use some gasket glue and reattach the new gasket and pan. I would find out what level of torque you need for the bolts and use a torque gauge to tighten the bolts. Add oil and drive.

Oct 01, 2014 | Vehicle Parts & Accessories

1 Answer

Where do I check the transmisson fluid on a 2006 cobolt

The 2006 Cobalt does not have a dipstick check tube at all. It is normally a non-serviceable component unless there is a leak. When the pan is removed, for service you would normally add 6.9 US quarts to the transmission. I will paste the GM instructions for servicing the pan below.

2006 Chevrolet Cobalt
Automatic Transmission Fluid Filter and Seal Replacement
Tools Required:
• J 6125-1B Slide Hammer
• J 23129 Axle Boot Remover
Removal Procedure

1. Raise and support the vehicle.
2. Place the drain pan under the transaxle oil pan.

Notice: When removing the oil pan bolts, be careful not to damage the oil pan sealing surfaces. Such damage may result in oil leaks in this area.
3. Remove the oil pan bolts from only the front and the sides.
4. Loosen the rear oil pan bolts about 4 turns.
5. Lightly tap the oil pan with a rubber mallet or pry in order to allow the fluid to drain.
6. Inspect the fluid color.
7. Remove the remaining oil pan bolt
8. Remove the oil pan.
9. Remove the oil pan gasket.

10. Remove the oil filter. Use a long screwdriver in order to pry the oil filter neck out of the seal.
11. Check the oil filter seal for damage or wear.
12. As needed, remove the seal using the J 6125-1B and the J 23129 .

Installation Procedure
1. Install a new seal, as needed. Before installing, coat the new seal with a small amount of J 36850 or petroleum jelly.
2. Install a new filter into the case
3. Install the oil pan gasket. Use a new gasket if the sealing ribs are damaged.
4. Clean and dry the oil pan. Inspect the pan for damage and replace the pan if necessary.
5. Install the oil pan.
6. Clean and dry the oil pan. Inspect the pan for damage and replace the pan if necessary.
7. Install the oil pan.
8. Install the oil pan bolts.

Tighten the bolts to 10 N·m (89 lb in).
9. Lower the vehicle.
10. Fill the transaxle to the proper level. Refer to Fluid Capacity Specifications .
11. Inspect the pan for leaks. Recheck the transmission fluid level. Refer to Transmission Fluid Checking .

Apr 27, 2014 | YouTube Videos

1 Answer

Deluxe buffet server DBS 999

Nostalgia does not sell replacement parts for any of their equipment.

Feb 16, 2014 | Nostalgia Electrics Helman Group CCP-509...

1 Answer

I purchased a model ccp-509 from a friend and found that it does not have a removable collection tray . How do I go about purchasing one.

Nostalgia does not sell any parts, anywhere. Your best bet is to find a used broken popper, and buy it for the parts.

Oct 02, 2013 | Nostalgia Electrics Helman Group CCP-509...

1 Answer


Parts for Nostalgia Electric are not available anywhere.

May 01, 2013 | Nostalgia Electrics Margarator Margarita...

1 Answer

Is transmission fluid pan accessable from underneath car?

Yeah, that's how it is done. Use jackstands or blocks under car. Raise enough that you can work comfortably underneath. The pan is on the very bottom of the transaxle. Loosen all pan bolts a turn or two, then remove bolts from one end, letting pan start lowering, catch fluid with drain pan. When fluid level in the pan gets low, finish removing all pan bolts, and pull the pan off. Filter is right there underneath the pan.

Dec 27, 2012 | 1995 Ford Escort

1 Answer

How do I change the transmission fluid and filter? 1999 GMC Jimmy 4wd

Its not really that hard. You just need to take your time and a very large pan. Your filter is just in side the trans pan. The pan will have to be dropped. A ratchet and socket will make short work of it. Just undo the bolts on the trans pan( undo 3 corners and the bolts on that side, allowing the pan to lean to drain some of the fluid). Hold pan steady, and undo remaining bolts. Lower the pan. Now its time to scrape the old gasket off the pan and trans case. Please clean to metal, don't want leaks. Remove the old filter, and replace with the new one. Install the gasket to the pan, and bolt the pan back into place. If you put 4 bolts from around the pan, makes it easier to put the rest in. Now to refill the trans, you need a funnel and add the fluid ant the dipstick. Bring it back up to level. This job will take a beginner about one hour. Hope this helps

Jan 02, 2011 | 1999 GMC Jimmy

Not finding what you are looking for?
Kitchen Appliances - Others Logo

Related Topics:

590 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nostalgia Electrics Kitchen Appliances - Others Experts

Anthony Ward
Anthony Ward

Level 2 Expert

397 Answers

Sheldon Dedek

Level 3 Expert

909 Answers

Gil Shultz

Level 3 Expert

3388 Answers

Are you a Nostalgia Electrics Kitchen Appliances - Other Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides