Question about Asko W6441 Front Load Washer

1 Answer

W6441 Error message

How do I fix error message F4 for the Asko W6441?

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Mentor:

    An expert who has written 3 tips or uploaded 2 video tips.

  • Expert
  • 413 Answers

Google this with the model # and the brand along with the F4 error code

Posted on Jul 29, 2015

Ad

1 Suggested Answer

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Asko service


Please refer page 12 and 24 in the washer manual to find out how to open the locked door. You have to press the door open button for 3 secs at end of cycle.


Asko Front Load Washer Use and Care Guide W6021 W6441 W6761...

Aug 10, 2014 | Asko W6441 Front Load Washer

1 Answer

F3 Error Message


F3 is a pump problem check the pump trap and clean it this should clear it up...

Aug 25, 2007 | Asko W6441 Front Load Washer

1 Answer

I have an f3 and f4 error code on asko washing machine front loader. i know what the error codes are just dont know where they are anyone can help I need it thanks


F3 indicates a problem with the drain pump. At the bottom left of the machine, theres a square cut-out. This is where the drain pump is located. Using a flat head screwdriver or similar object, insert in opening on right side and gently pry open the drain pump cover.
Once the cover has been opened, be careful when opening the drain pump, as there is always a little water left in the drain pump. Before you open the drain pump, place a small container on the floor below the drain to catch the water. Pull the small black hose from the door and let the water drain into the container. You can now open the drain pump to clean it out. Also clean the pump rotor at the back of the pump housing. Replace the drain cover and reconnect the drain hose securely back to its position on the door. Close the cover.

F4 indicates a problem with the water inlet valve. Make sure the water supply is fully turned on. If no water enters the machine, then turn water supply off. Disconnect the hoses from the water inlet valve to see if the strainer in the inlet connection is blocked. Reconnect the hoses and turn on water supply. Hopefully this solves your problem.

Feb 14, 2011 | Asko W6441 Front Load Washer

1 Answer

What does a "F4" code mean


Hello,

Welcome to FixYa.

I can tell you on the Asko machines the "F4" indicates an error related to the thermistor.

Whether the thermistor is actually at fault is another matter. It may be a faulty wire connection, the thermistor has become dislodged from the bracket mounting it to the tub or yes indeed the thermistor may be at fault.

Here`s what to look for and what it does...

THERMISTOR
Part no. : 80 616 63
Resistance: 40-60K ohms
Room temperature: 68°-86° F (20-30° C)

The thermistor ( for temperature measurement ) is
located between the motor cradle and the holder.

The thermistor measures and controls the water temperature via a heating element. In the event of errors the heater is switched out and F4 displays if the thermistor short-circuits or is disconnected from the program control board or programmer.

**unplug the unit from the dryer or wall whichever applies to your situation...safety first**

If you are capable, remove the rear panel and top panel to ohm out the thermistor to verify if it is within` the values I provided...or perhaps it has dislodged from it`s position as I alluded to.

In the event you need a thermistor and you feel you can replace it yourself I`ll show you how...I do recommend calling in an authorized Asko service provider.

CHANGING THE THERMISTOR

1. Remove the top cover as mentioned
2. Remove the rear panel as mentioned
3. Remove the thermistor by pulling it out to the left.
4. Remove the thermistor header connector from the program control board.
5. Install the new thermistor by threading it through the hole between the cradle and holder.
6. Connect the thermistor to the program control board.
7. Replace the rear panel.
8. Replace the top cover. (Don't forget the two
star washers for the outer screws.)


Hope this helps move you forward or at least gives you an idea of what needs to be looked at.

Let me know if you require further assistance or this is not clear I can post pictures/illustrations. Thanks for choosing FixYa today.

Good luck.

Regards,


Macmarkus :)

Sep 21, 2010 | Asko W6441 Front Load Washer

3 Answers

F4 error message. Cleaned out screen at water inlet and still get error message.


There may be excess water in the water reservoir. Empty the washer Turn it off at the mains, and unplug it, then put some old towels on the floor, tip the washer forward until the excess water comes out, Reconnect and try again. Hope this helps it works for me and saves ££££'s in repair fees

Oct 04, 2009 | Asko W6461W 24" Front Load Washer w/ Delay...

1 Answer

My Asko W6441 front load washer F3 message


Hello. You said that you checked the drain line for obstructions, but did you check the pump? I would remove the hoses from the pump and using a flashlight, look into the suction port on the pump. Check the pump for any obstructions (like the occasional stray sock) and check the pump impellers. Look for broken/missing blades and ensure that the impeller spins freely. If there are missing/broken blades or if you cannot get the impeller to spin freely, the pump is defective. You may have already done this, and if so I apologize. Anyway, hope this helped and best wishes.

Aug 28, 2009 | Asko W6441 Front Load Washer

1 Answer

ERROR F3 - WHAT DO I DO?


hi the error shows bcoz of ur door problem...
replace the door lock and ur problem will be solved...

May 24, 2009 | Asko W6441 Front Load Washer

1 Answer

Asko washing machine


f4 code is sapose to be the thermister, i'm looking for whosale parts supplyer can you help?

Mar 13, 2008 | Washing Machines

1 Answer

F3 Error Message


The F3 error code relates to a pump problem Check pump trap and clean. Good luck!

Aug 25, 2007 | Asko W6441 Front Load Washer

Not finding what you are looking for?
Asko W6441 Front Load Washer Logo

287 people viewed this question

Ask a Question

Usually answered in minutes!

Top Asko Washing Machines Experts

Gerry Harvey
Gerry Harvey

Level 3 Expert

1481 Answers

Joseph Hoffmann

Level 3 Expert

1755 Answers

ROB

Level 3 Expert

858 Answers

Are you an Asko Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...