Question about Chevrolet 1996 Chevrolet Blazer S10/jimmy S15 Radio

Open Question

2000 s10 what causes broken teeth on flywheel

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
tripletauto
  • 1450 Answers

SOURCE: 1984 s10 2.8 manual trans. flywheel causes engine to vibrate

no should be same engine. check your engine mounts and tranny mount. how bad a vibration? sometimes after installing engine the trans gets shifted around and if mount was worn it will allow it to hit crossmeber and vibrate.

Posted on Jan 16, 2009

Ad
  • 255 Answers

SOURCE: grinding when starting, replaced starter one month

The flywheel is worn in that specific area. Engines tend to stop in the same one or two positions, and it is those teeth that get cachunked every time you turn the key. This is ok if the bendix does a good job of threading the gear into the flywheel teeth, but the problem is that now that the teeth are half worn away, the starter attempts to mount its gear to the teeth, but before the gear is fully seated, the contacts in the motor make, the motor starts to turn, and the not-yet-seated gear bounces off of the flywheel teeth. This is what causes the teeth-grinding sound (your teeth grinding in your mouth too!) when you turn the key. . There are two solutions: The first is to, of course, replace the ring gear. . The second is hard to explain, but a good starter rebuild center (if there is such an accessible animal around anymore) will know what I'm talking about: The starter gear must have the lagging edge of each tooth ground so that each tooth will look like a chisel. The "pushing" side of each tooth must be straight and come to the point (and not be beveled). The "non-pushing" lagging side of each starter tooth should have the bevel ground in on that side. This grinding is done easily by a small angle grinder or a Dremel Tool with a cutoff wheel. . This does one thing: It assures that the gear will "spin in" without bouncing. If ground correctly (it's not hard to do), you will get successful starts every time. This is a common fix for Toyota 4-cyl with this horrible all-too-common problem. Good luck.

Posted on Nov 25, 2009

rwwood81766
  • 5513 Answers

SOURCE: what causes teeth on flywheel break

Improperly engaged starter, kickback, weak battery . Cavities, just joking. How long has it done this ?

Posted on Oct 21, 2015

  • 233 Answers

SOURCE: what causes broken teeth in flywheel

Hi I am a tech mechanic its years of wear or starter put in wrong also check piston out make sure its not locked up

Posted on Oct 21, 2015

  • 53746 Answers

SOURCE: 1970 Chevy El Camino starter broke teeth on flywheel. What would cause this?

several reasons
the teeth on the ring gear were damaged from continuous grinding during pinion engagement or engagement of the starter when the engine is running causing a burring of the teeth that altered the mesh ability and jammed the ring gear and pinion
metal in the teeth of the ring gear that causes a jam in rotation
starter motor not engaging before rotating
wrong no of teeth on replacement starter pinion or starter motor

Posted on Dec 17, 2016

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

What causes damage flywheel on bmw is it common fault


-you mean broken teeth...? If so possibly crank the engine while it's still running.


Good Luck


Mai

Jan 07, 2016 | BMW X3 Series Cars & Trucks

1 Answer

What causes broken teeth in flywheel


Hi I am a tech mechanic its years of wear or starter put in wrong also check piston out make sure its not locked up

Oct 21, 2015 | 2000 Chevrolet S-10

1 Answer

Starter stays engaged on my 06 Chevy Malibu


There are a few possibilities...
  1. Starter improperly shimmed and is biding to flywheel.
  2. Starter or flywheel teeth worn causing binding (not likely)
  3. Starter solenoid return spring broken.
  4. Ignition switch problem causing starter to stay powered after key released.

Aug 02, 2014 | 2006 Chevrolet Malibu

2 Answers

65 mustang l6 200 cid. Starter motor seems to keep "locking" up flywheel. Why is it doing that? Best fix?


This could be a starter solenoid defect but if this has been a problem for some time, the ring gear could be chewed up or have missing or broken teeth. Itmay be possible to fix the problem by shimming the solenoid but I would check out the other items first

Jan 28, 2013 | 1965 Ford Mustang

1 Answer

Flywheel


The most commun problem is the starter selenoid 2.-the starter in most auto parts they check free and when you remove the starter check the flaywheel teeths turn the fly wheel with big screewdriver on the starter area and check all flyweel teeths condition if you have any broken teeths replace the flyweel

Jul 22, 2012 | 2000 Ford Explorer

1 Answer

2000 Chevy s10 manual changed starter still won't start the starter is spinning but the engine won't turn over.


Do you have the correct starter and is it grinding, this sounds like a bad flywheel or wrong starter or even a bad one. look at teeth of flywheel and see if they are damaged. good day

Jun 19, 2011 | 2000 Chevrolet S-10

2 Answers

Grinding noise when ignition is turned


THe starter engages the fly wheel and in the process turns the motor over to cause it to crank. The grinding can be a bad starter causing the gear to either not engage fully or not disengage. It can also indicate missing teeth on the flywheel from damage from starter. If the car cranks and grinding goes away it points to the starter solenoid not engaging properly.. pushing gear into contact with flywheel. I would recommend replacing the starter and you can replace it with a good mechanical knowledge and DIY.

Jun 08, 2010 | 1997 Chevrolet Cavalier

1 Answer

My flywheel has broken.whats the cause .iv only done 27000 miles


Flywheels are pretty robust part of an engine. How do you know it's broken? Or, is it that the starter teeth are stripped from the flywheel?

Dec 13, 2009 | 2004 Land Rover Discovery

1 Answer

99 devile, have to manualy move the crank to get starter to inguage sometimes. it is the 4.6 northstar.what would cause this...


broken tooth or wore out teeth on the flywheel. The flywheel is mounted to the engine when the starter is engaged its gears (teeth) engage the flywheels teeth and turn your engine. The reason you can turn the motor and try again and it grabs is because you have turned it enough to grab some of the good teeth you have left. You must replace the flywheel. Hope this helps

Oct 14, 2009 | 1999 Cadillac DeVille

Not finding what you are looking for?
Chevrolet 1996 Chevrolet Blazer S10/jimmy S15 Radio Logo

Related Topics:

222 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Audio Players & Recorders Experts

D. E. Hev

Level 3 Expert

1187 Answers

Marvin
Marvin

Level 3 Expert

85178 Answers

Lawrence Oravetz

Level 3 Expert

10543 Answers

Are you a Chevrolet Audio Player and Recorder Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...