Question about Krups Small Appliances Espresso Machine

1 Answer

While making coffee , water begins to flow underneath, making coffee is interrupted , the device enters in the auto test mode and soon displays error code 06. What to do to fix the problem?

I replaced the water filter and I run a cleaning procedure. Machine type: Krups EA 8050

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Krups Master
  • 1,355 Answers

It's not a job for the faint hearted on one of those machines. The 2 places most likely to be leaking are the barista seal on the bottom of the boiler or the distributor which is a motor driven tap that sends the water from a single pump to do various functions. There are also various hoses in there that are under high pressure and can fail in an instant. I have just read the error codes and it seems that the barista seal is going to be the LEAST likely cause of the leak but I would replace it during the process if you are going to have that area close to being apart.

Posted on May 31, 2016

Ad

6 Suggested Answers

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
Richie_asg1

Richard Perkins

  • 1036 Answers

SOURCE: Krups FME2 will not flow water.

Hi,
Does it sound like it is boiling water at all?

If it is boiling, but not giving hot water, then the one-way valve is stuck.
If it is not getting hot (on the soleplate base) then usually the element has blown.

These machines use the steam generated by boiling as a means to move the water up - like a geyser, and need the heat to move the water.

Replacement elements are available, and the valves usually just require cleaning.

Posted on Jun 29, 2008

Anonymous

  • 1 Answer

SOURCE: krups xp 7240 cofee machine

Hi,
for the error code 06. (this is what I got from a guy on a tech support line)

The issue is with the waterfilter. If you haven't changed it for a long time - change it. If you recently got a new one follow these steps:
- take the filter out
- unplug the machine from electricity
- plug it back in
- install filter (go into prog- service- install new filter)

It should remove the error. Haven't tested that yet, but that's what I got :)

Good luck

Posted on Apr 27, 2009

Anonymous

  • 5 Answers

SOURCE: Error Code 9 on a Krups XP7240 Expresso machine

After I changed piston sealing I get the same error 09. It was caused by missing connection to the thermoblock temperature sensor. In my case both connectors for thermocouple were cracked. They are located directly on the body of thermoblock, below two fuses, covered by rubber housing. After I solder them again on the position error 09 disappeared. Unfortunately it is necessary to open at least front panel of the machine. Moreover I tink that there is also important to save polarity of those two cables.

Posted on Aug 07, 2009

jon9621

  • 4 Answers

SOURCE: KRUPS XP7240 leaking water

My XP7240 has the same problem. I went through all cleaning cycles and the filter in the boiler still gets clogged up with coffee oils. This causes back pressure and blows the boiler seal out. Easy replacement if you can turn a screw driver.
Part number for Seal: MS-5015004. You might as well change the Jack too. (the part that slides into the boiler that compresses the ground coffee. (this is a redesigned double seal unit) Part Number MS-0697072.
Both these parts you can get at http://www.krups.com/Tools/Contact/Contact.htm choose your country and email the parts list. Mine cost in Australia $27.00 including shipping.
Good luck.

Posted on Sep 16, 2010

niclas228

  • 1 Answer

SOURCE: Error code 07 on my Krups XP 7220 coffee machine

Error code 07 on my Krups XP 7220 coffee machine what to do? Nick

Posted on Oct 24, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Why h and 2 appear


H2 means Thermistor open.

To reset the error, go to simulation mode by pressing # interrupt C interrupt (press these four buttons as soon as possible) The display will go off. Then enter 1, 4 and press start key, The machine will restart automatically, If the error continues check the thermistor and connections of the heater section. Replace the heater assembly if required. Replacing the main PCB is the final step.

Dec 01, 2012 | Sharp AR-5320 Black and White Copier

1 Answer

I get an NF error code and the washer sounds like it's filling, but never does, and then there is water in the detergent dispenser.


Hi

Thanks for using FixYa. Error NF means No Fill. The washer has tried to fill but was unsuccessful. NF indicates No Flow. There is something that is interrupting the inbound flow of water to the washer, either hot or cold. Sometimes this happens when water service in the area is interrupted, creating an air pocket that causing the water valve not to sense water. Try running the diagnostic test by:
  • Press the delicates and heavy soil keys together for 3 seconds.
  • You are in the service mode.
  • Now, press wrinkle free key, cold water should start entering.
  • Then, press the cotton sturdy and hot water should flow.
  • To exit the test mode, either unplug the machine or press the delicate and heavy soil again for 3 seconds.

Please do rate the solution if the issue is resolved or post a comment for further assistance.


Thanks
Rylee

Sep 22, 2010 | Samsung WF328AA Front Load Washer

1 Answer

I get a 3E error code or nf. My fill valves don't seem to be working properly. I get no water in my fabric softener cup. Fill is slow.


Hi


Thanks for using FixYa. Error NF means No Fill. The washer has tried to fill but was unsuccessful. NF indicates No Flow. There is something that is interrupting the inbound flow of water to the washer, either hot or cold. Sometimes this happens when water service in the area is interrupted, creating an air pocket that causing the water valve not to sense water.

Try running the diagnostic test by—
  • Press the delicates and heavy soil keys together for 3 seconds.
  • You are in the service mode.
  • Now, press wrinkle free key, cold water should start entering.
  • Then, press the cotton sturdy and hot water should flow.
  • To exit the test mode, either unplug the machine or press the delicate and heavy soil again for 3 seconds.
Please do rate the solution if the issue is resolved or post a comment for further assistance.


Thanks
Rylee

Sep 12, 2010 | Maytag Washing Machines

2 Answers

I am getting error code...NF


Hi


Thanks for using FixYa. Error NF means No Fill. The washer has tried to fill but was unsuccessful. NF indicates No Flow. There is something that is interrupting the inbound flow of water to the washer, either hot or cold. Sometimes this happens when water service in the area is interrupted, creating an air pocket that causing the water valve not to sense water.

Try running the diagnostic test by—
  • Press the delicates and heavy soil keys together for 3 seconds.
  • You are in the service mode.
  • Now, press wrinkle free key, cold water should start entering.
  • Then, press the cotton sturdy and hot water should flow.
  • To exit the test mode, either unplug the machine or press the delicate and heavy soil again for 3 seconds.
Please do rate the solution if the issue is resolved or post a comment for further assistance.


Thanks
Rylee

Sep 04, 2010 | Maytag Neptune FAV6800AW Top Load Washer

1 Answer

LED is flashing nF. What does this indicate? Washer is a front load Maytag Neptune, mod# MAH 8700 AWW.


Hi


Thanks for using FixYa. Error NF means No Fill. The washer has tried to fill but was unsuccessful. NF indicates No Flow. There is something that is interrupting the inbound flow of water to the washer, either hot or cold. Sometimes this happens when water service in the area is interrupted, creating an air pocket that causing the water valve not to sense water.

Try running the diagnostic test by—
  • Press the delicates and heavy soil keys together for 3 seconds.
  • You are in the service mode.
  • Now, press wrinkle free key, cold water should start entering.
  • Then, press the cotton sturdy and hot water should flow.
  • To exit the test mode, either unplug the machine or press the delicate and heavy soil again for 3 seconds.


Please do rate the solution if the issue is resolved or post a comment for further assistance.


Thanks
Rylee

Aug 25, 2010 | Maytag Washing Machines

2 Answers

My Maytag Neptune will not spins and gives the code nf. I have been told that there is a reset code. Does anyone know the code?


Hi


Thanks for using FixYa. Error NF means No Fill. The washer has tried to fill but was unsuccessful. NF indicates No Flow. There is something that is interrupting the inbound flow of water to the washer, either hot or cold. Sometimes this happens when water service in the area is interrupted, creating an air pocket that causing the water valve not to sense water.

Try running the diagnostic test by—
  • Press the delicates and heavy soil keys together for 3 seconds.
  • You are in the service mode.
  • Now, press wrinkle free key, cold water should start entering.
  • Then, press the cotton sturdy and hot water should flow.
  • To exit the test mode, either unplug the machine or press the delicate and heavy soil again for 3 seconds.
Please do rate the solution if the issue is resolved or post a comment for further assistance.


Thanks
Rylee

Aug 22, 2010 | Maytag Neptune MAH5500B Front Load Washer

3 Answers

My 7 year old GE Profile Side by Side will not get


Self Diagnostics
To enter Self Diagnostic mode, both temperature control panel displays must be illuminated. A display
can be illuminated by pressing an adjacent temperature adjustment button. When both displays are
illuminated, set the freezer and refrigerator temperature settings to 5. Simultaneously press and hold all
4 temperature adjustment buttons for approximately 3 seconds. A flashing 0 in the refrigerator and
freezer displays will indicate that the refrigerator is in Self Diagnostic mode.

For temperature control panels with single-digit displays, the COLDER temperature adjustment button
will increment the numbers up and the WARMER temperature adjustment button will increment the
numbers down. Use the freezer temperature adjustment buttons to enter the test code number in the
freezer display. Use the refrigerator temperature adjustment buttons to enter the test code number in
the refrigerator display. When a test code has been entered, the displays will flash to confirm the test.
Press the HOLD button for 3 seconds to begin the test.
For temperature control panels with 3-digit displays, the COLDER temperature adjustment button will
increment the numbers down and the WARMER temperature adjustment button will increment the
numbers up. Use the freezer temperature adjustment buttons to enter the test code number in the
freezer display. Use the refrigerator temperature adjustment buttons to enter the test code number in the refrigerator display. When a test code has been entered, the displays will flash to confirm the test
code. Press any button other than a temperature adjust button to begin the test.
When testing has been completed, do one of the following things:
• Enter code 1 5 to completely reset the system.
• Enter code 1 6 to exit diagnostic mode. GSS manual


If you need further help, reach me via phone at https://www.6ya.com/expert/dan_73bbd84fe1d95b61

May 15, 2010 | GE (PSS26MSRSS) Side by Side Refrigerator

1 Answer

E1 error code


Fault is 1E- this indicates a water inlet error.
To access test mode: press and hold Normal+Eco, and press Power. Release buttons. Then press Start(display n:01).Press Start again (display shows water level frequency-not important). Press Start again-(display n:03-motor will be running). Press Start again (display n:04-drain pump will run). Press Start again (display n:05-inlet valve will come on and machine should fill with water). You have now tested major components are working-if you keep pressing start you will scroll thru and test other functions, like heater, dispensor etc, but not needed for your fault.
If Machine didn't fill with water in test mode, you probably have a faulty inlet valve (test resistence should be approx 3.7-4 k ohm).
If inlet valve has tested OK ie machine filled with water in test mode then:
Disconnect from power.
Remove side panels (need to remove top, and bottom front panel to then be able to remove sides)
- Check no water in base of machine-water in base will indicate machine has leaked and activated the safety device which shuts off inlet valve.
- If OK, you probably have a faulty flow meter(measures water intake). Located left hand side of machine, large plastic compartment, which has a sensor at the bottom with 3 wires (red,white,black) that go up to control board. Replace entire flow meter assy-relatively inexpensive part.
- If you still have problem, then control board is faulty, but in my experience it is much more likely to be flow meter

Aug 05, 2009 | LG Dishwashers

1 Answer

Sharp Al-800 H4 Error Code


Press : CLEAR key - INTERRUPT key - O - INTERRUPT key.
The copy quantity display goes off and the machine is ready to receive input of test command number.Enter the two digit number to select the test commands.The test command number entered will be displayed in the copy quantity display.Press the PRINT switch.The operation corresponding to the entered test command number will be performed.For the test command 13 and 14 since test commands 13,14 are used to clear the contents of the diagnostic status (U1,H3,H4)stored in the LSI,the diagnostic mode will be automatically canceled after completion of the test commands.

Jul 30, 2009 | Toshiba e-Studio120 Copier

1 Answer

No instructions on programming auto shut-off time (feature listed on box).


You have to use the "Auto-Off" feature, which is located on the same button as on/off:
The automatic shutoff time (ASO) can be
programmed to shut off immediately after
brewing (0:00) or up to 4 hours later. The
default shutoff time is 2 hours.
Press and hold the On/Off button to display
current shutoff time. To change the preset
time, press and hold the On/Off button until
the red power light and LCD display begin to
flash. This signals that you have entered the
Set automatic shutoff mode. Set the time
you want coffee to begin brewing by
following the instructions in “Entering Time
Set Mode.”
When the coffeemaker shuts itself off, two
tones will sound.
NOTE: Automatic shutoff may be
programmed either before or during coffee
brewing. If you program the auto shutoff
time after brewing is completed the unit
will automatically account for elapsed time.
For example, if you set the auto shutoff for
40 minutes and 25 minutes have already
elapsed, the unit will shut off automatically
after 15 minutes (40 minutes minus the 25
elapsed equals 15 minutes).

-Tha Mp3 Doctor

Apr 15, 2009 | Cuisinart Grind and Brew 10 Cup Coffee...

Not finding what you are looking for?
Krups Small Appliances Espresso Machine Logo

229 people viewed this question

Ask a Question

Usually answered in minutes!

Top Krups Coffee Makers & Espresso Machines Experts

Pierre Laplante

Level 3 Expert

2042 Answers

Ray Murphy

Level 2 Expert

68 Answers

Marvin
Marvin

Level 3 Expert

85206 Answers

Are you a Krups Coffee Maker and Espresso Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...