Question about DISH Network Televison & Video
Check the remote control for its infrared emission. Check it with fresh batteries. Check it by pressing all the keys. You can detect the presence of infra-red emission from the remote control, using a cell-phone camera. If you wish to get more details about how to check a remote control, please visit this site. One among the posts has details about it. In some cases, the remote control might need to clean.
Search the site by type in this key phrase "how to test a remote control "in the "search box at the top right of the display window of the Homepage" to get the related post quickly.
https://www.youtube.com/watch?v=jsSCNCW3IbQ [open and clean]
https://www.youtube.com/watch?v=Qp-l1uh-5gE [open and clean]
Posted on Mar 27, 2017
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
Here's a link to this great service
Posted on Jan 02, 2017
You will need a DP or Legacy twin or quad, or DPP twin without using an external switch. If you use Legacy Duals, or DP Duals you will need a switch. USUALLY a SW21 is used to combine the signals but you may have a different one in use if at all.
The primary thing to remember when using a switch is that you must use the same type of LNB as switch e.g. Legacy switches with Legacy LNB's and Dish Pro switches with Dish Pro LNB's.
Check your LNB type. Legacy LNB's have only a Dish Network Logo on them, Dish Pro has DP on them and DPP have DP PLUS on them.
One of three things could be the cause:
1. Line of site. Must be clear of all obstructions to ensure adequate signal.
2. You have a faulty switch, or conflicting LNB and switch, or no switch at all.
3 you may have a bad port on the LNB.
As a fail safe check that your mount is level and plumb. You also may have the dish pointed directly at 119. Check the Skew and elevation settings as well. If LOS IS THE ISSUE YOU MAY NEED TO RELOCATE THE DISH OR REMOVE THE OBSTRUCTION.
In some extreme cases microwave towers and High Voltage lines also pose a problem but doubt this is the case for you.
Posted on Sep 04, 2008
Please follow the steps below to program your remote control to equipment other then your DISH receiver:
Note: If you start this procedure and at any time and do not press a button within 20 seconds, the remote will end the procedure automatically. Simply start over again. Use the TV button for your TV, the VCR button for your VCR or DVD player. These Mode buttons are located at the top of your remote control.
1. With the desired equipment on, press and hold the correct Mode button until all mode button backlights illuminate, then release.
2. Press the numbers 5-0-0 on the remote control.
3. Press the Pound (#) button on the remote.
4. Press and hold the correct Mode button until all mode button backlights illuminate, then release.
5. Press and release the Power button on the remote control.
6. Press the Up button once a second while pointing the remote at the desired equipment. If the code for the equipment comes up, the equipment will power off.
7. Press the Pound (#) button. If the code entered is valid for the remote, the mode light flashes three times.
8. To verify the code works try several different functions for that equipment.
We cannot guarantee our remotes will work all other devices. If this does not correct the issue, unfortunately our remote will not work for that device. We apologize for any inconvenience this may cause.
Lone99star. Please rate this solution.
Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/jason_77a19afa8d604dee
Posted on Feb 14, 2009
You will have to use the AUX button to program it to . Press AUX till lights light up then enter 4 digit code (if you have a 3 digit code use 1 as the first number) then press pund. And your good to go howevetr the only functions that may work is powere on an off.
Posted on Nov 12, 2009
Codes didn't work. Power scan did though. I used to work for Dish Network in AZ. First training class when it opened in AZ. I call it now DOUCHE NETWORK. Corporate America SUX, and DOUCHE NETWORK follow that to the fullest extent of the LAW.
Posted on Jun 12, 2010
Tips for a great answer:
Jul 04, 2015 | DISH Network Televison & Video
Jul 22, 2013 | DISH Network Televison & Video
Mar 13, 2011 | Directv (R10) DTV Receiver / 70-Hours...
Feb 09, 2011 | Bose Cinemate Digital Home Theater System...
Jan 23, 2011 | DISH Network IR Remote Control
Dec 25, 2010 | Bose Cinemate Digital Home Theater System...
Nov 21, 2010 | Bose 35503 Remote Control
Nov 21, 2010 | Bose Wave Radio II
Jul 05, 2010 | Bose 3 2 1 GSX System
Feb 17, 2010 | Bose Cinemate Digital Home Theater System...
Jan 03, 2019 | DISH Network Televison & Video
55 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: