Question about Ricoh Office Equipment & Supplies

1 Answer

My ricoh aficio machine has a error problem SC672, what i can do .

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Welcome Back:

    Visited the website for 2 consecutive days.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 10 Answers

Memory or hard drive error.

Posted on Oct 18, 2017

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
spinal
  • 287 Answers

SOURCE: Ricoh Aficio 1224c

Hello billboards,
SC 570 means that despite the fact that the the copier had been giving a "FUSER OIL LOW" prompt in the upper left hand corner of the display for quite some time, the prompt was ignored and now the oil is more than low it is empty. You will first need to aquire fusing oil for your machine.Typically it would be purchased from the same source you would aquire toner as it is something that is consumed as the copier is used similliar to toner. Once you have the oil you will need to replenish the copier's supply of oil. To do this you will need to access the back of the machine. Once you are at the back of the machine,look down to the lower right hand corner. You will see a small square panel with what I would describe as an oversized white plastic flathead screw that needs to be turned counterclockwise to release the small panel/cover. Once you remove the cover you will see a clear container witha black screw on cap. Unscrew it,and fill the container with the oil and stop filling when it reaches the neck of the container. Button everything back up and now you are halfway out of the woods. Now we go to the front of the machine. We need to reset the code. There is a yellow rectangular button above the nine key pad used to enter the number of copies you want. Now that you have located it, press it once and then press the "1" then the "0" then the "7" and then press the round red stop button and hold it down until the screen changes and beeps. At this point the display will have several blocks showing. One of the blocks will say "copier".Press the copier block. Now you will have a drop down menu to the left and several options across the top of the display. At the top,from left to right,the fourth box should say "SP DIRECT" and should actually already be highlighted. At this point,merely press "5810" on the keypad and then press the " # " pound sign. The pound sign means enter. At this point you should see a prompt that says something like "SC reset" and there will be a bar below the prompt that says "EXECUTE" .Press the execute button. This resets the code. But now you must turn the main power off (the red switch located next to your left knee on the front panel of the copier) and wait a few seconds. Now turn that switch back on and you should be good to go. I just reviewed my instructions and wanted to stress that the yellow button above the nine key pad says clear/stop. Just wanted to be more specific. I bet you have this problem whipped in no time! I hope this helps.Take care and good luck.And please feel free to let the folks at "FIX YA" know if I helped you. I don't get paid by them but I like the pats on the head . :-) ...........spinal.......

Posted on Apr 19, 2008

Bubbabear64
  • 2794 Answers

SOURCE: Error code SC305 for Photocopier Ricoh Aficio 1224c

Its a charge corona cleaning error. Try turning the power off, wait 10 seconds and turn it back on.

If that doesn't reset it, it could be the pcu, toner collected on the mechanism.

If turning it off and back on isn't fixing it, you should get a technician to look at it to see what the trouble is.

Posted on Jun 19, 2008

  • 14 Answers

SOURCE: Error code SC305 for copier ricoh aficio 1224c

Hi,
This SC code relates to the charge corona cleaner not working or not working properly. the charge corona is located towards the bottom left of the machine after opening the front cover. It will have a screw you can undo by hand and a cable with an end like a telephone cable plug. toner may have fallen in to the unit or the motor that drives the cleaner along the wires has decided to jam up. remove the charge corona and blow it out with compressed air. You can also remove the end of the unit and check that the motor is not gummed up. Be very careful you do not break the hair thin corona wires! Hope this helps.

Dave T

Posted on Jun 22, 2008

  • 1 Answer

SOURCE: ricoh aficio 2022 error code sc542

1. Mode(Yellow Button)
2. 107
3. Press STOP Button for 3 second (RED Button)
4. Copy Sp
5. 5810#
6. Excute
7. Power Off
8. Power On


Posted on Feb 24, 2009

M2Tech1
  • 313 Answers

SOURCE: error codes SC545 for Ricoh Aficio 1045

yes you may it refers to a temp error int eh fuser... you may have a faulty thermistor or thermo fuse.. if you go into teh service mode by presssing teh yellow clear butto and then press 107 and then hold down the stop button the sreen will change turn the machine off and turn on again see if the errpr goes if it does it could have been just a temp error if it warms up then comes back on again you will have to look at the fuser.. you can check the fuser by touching the casing and see if it is warm after you have turned the machine back on..if it is warm the error could just be due to a build up of toner on the thermistor.. if you know about machines you can take the fuser out by opening the front of the machine up look to top right where fuser is there is a screw under the blue dial on the fuser take that out the fuser slides out put it on some paper and on the right hand side is the thermistors held inby a small screw if you take them out you may see some build up of toner on the resistor carefully clean this off.. put back together and turn on .. hopefully it will run ok.. good luck A

Posted on Jun 26, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My ricoh aficio MP3351 machine has a error problem SC672, plz kindly tell me what i can do???


SC672 occured when controller-to-operation panel communication error at startup After powering on the machine, the communication circuit between the controller and the operation panel is not opened, or communication with controller is interrupted after a normal startup.

.Controller stalled
.Controller board installed
incorrectly
.Controller board defective
.Operation panel connector
loose or defective

Make sure that the MBU is seated correctly. If not, SC672 occurs look at the picture to see what im talking about.

mbu-mpgtdnp1q1icgjyji5ew5m4c-1-0.png

Sep 29, 2017 | Ricoh Office Equipment & Supplies

1 Answer

My copier machine comes up with functional error code sc672. can anyone help


That error code appears to indicate 'Op panel to controller problem' see here http://multifunctionalcopier.blogspot.co.uk/2012/06/ricoh-error-code-list.html

Sep 05, 2015 | Ricoh Richo KR-5 with 35-70mm f3.5-4.5...

1 Answer

SC392 ERROR CODE


There's a video showing how to clear SC error codes: Resetting Ricoh Savin Lanier SC Error Code There's also a discussion here: Thread Ricoh Aficio 220 error SC392

Jun 30, 2014 | Ricoh 885288 Black Copier Toner Cartridge...

1 Answer

Error code is sc672 on display ricoh mp2550n


change the bicu board and the problem will be solved
Good luck.

Apr 05, 2014 | Ricoh Aficio 1013F Copier

1 Answer

Ricoh 1232c sc 672


The correct way to get into service mode is to first press the Yellow "CLEAR" button then press the numbers 1 >0>7 then press and hold the Red "STOP" button.... Good Luck

Jun 08, 2012 | Ricoh Aficio 1232C Color Copier

2 Answers

My 2022 shows an error code SC320 and also a error code SC672 what could be the problem


CS320 polygon motor (laser), you will need to replace it, it is not expensive!
CS672 control communication on start up, to many options, from circuit board to bad connection, you will need a tech for this.

Nov 23, 2010 | Ricoh Aficio 2022 All-In-One Laser Printer

2 Answers

We've a Ricoh MP3500 that is displaying an error code SC672 and directs us to switch the main power and switch back on. When switched back on, we have the same error code. Advice?


sc672 is a communication error between the controller board and some other component. Did you switch the machine off using the orange power switch on the lower left side, or just the power button on the operation panel?

With the power completely off and the machine unplugged, pull the controller board out by removing the two screws holding it in on the rear left side of the machine. (It should slide right out the side.) Check all of the connections on the board and make sure everything is sitting securely, then reinstall the controller board.

Worst case scenario, you might have a bad memory stick, bad controller board, or another bad circuit board, but more than likely there is a connector somewhere that just needs to be set securely. You can also remove the operation panel (two screws on the top of the panel and possibly two screws underneath it as well) and check the harness that connects the op panel board to the machine.

Jul 16, 2010 | Ricoh Aficio AP3800C Laser Printer

1 Answer

Ricoh 1035


It says communication error to control panel at station.

Turn the copier off, wait 30 seconds, and turn it back on again.

It should go away. If it doesn't a technician needs to come out and look at the problem.

Jul 31, 2008 | Ricoh Aficio 1035 Copier

Not finding what you are looking for?

Open Questions:

Office Equipment & Supplies Logo

Related Topics:

479 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ricoh Office Equipment & Supplies Experts

gggg

Level 3 Expert

904 Answers

Adorjani Laszlo

Level 3 Expert

1316 Answers

quennie732

Level 2 Expert

422 Answers

Are you a Ricoh Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...