Question about The Watches

1 Answer

I am attempting to put new batteries (CR2025 and SR6265SW) in my Stauer Colossus Hybrid. I need a diagram to reassemble the watch. Is an internal assemble of the watch available?

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • The Master
  • 29,187 Answers

I bet the batteries cost you more than 10 bucks. My advice is always have batteries replaced by a local jeweler. Cost $8 to $15 and is done whilst you wait.

Stauer 20410 Colossus Hybrid Analog Digital Stainless Steel Quartz Watch

How to change the batteries is not available online. Sometimes there are videos. You could ask the maker direct though.

https://www.stauer.com/

Posted on Dec 05, 2017

Ad

3 Suggested Answers

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Geoff

  • 125 Answers

SOURCE: my stauer atomic signal watch won't set correct time

Take a look at http://www.stauer.com/pdf/17468.pdf
I see that this watch gets it's time signal from Boulder, Colorado so it will only work properly in North America. Perhaps they also do models for the European market - if so I would expect them to work in the same fashion so the manual should still be relevant.

Posted on Aug 01, 2010

sigmaprecisi

sigmaprecisi

  • 1 Answer

SOURCE: How do I remove a link from the Stauer Colossus Hybrid Chronograph

Removing a link from the wrist band of the Stauer Colossus watch is a task that requires some mechanical talent. The links are held together with pins. These pins need to be pushed out. I strongly recommend the purchase of a "Watch Band Link Pin Remover" (got mine on eBay for $7). Prepared with this tool, the steps are as follows.

a) Separate the wrist band at the position where the strap and latch are held together. Careful! This pin is spring loaded.
b) The links that can be removed are marked with an arrow on the interior side. The pin should be removed in the direction indicated by the arrow.
c) With the previously mentioned tool you will be able to perform the hardest part, namely push out the pin by 3/16". In the image below note how the pushed out pin goes into the groove of the tool.
f72da118-a1b9-4051-8d6c-b43c4f308bd4.jpg
d) Use a small screwdriver or a punch with diameter of less than 0.07" (or 1.8 mm) in order to push out the pin completely (see second picture).
The push pin of the tool can be reversed which is helpful for re-assembly. I recommend smoothing the one end of the pin with a small file or sandpaper. This way the pin enters easily into the hole of the lower section. Else you run the danger of bending the link if the pin is not correctly positioned and you apply too much force.

Posted on Jul 05, 2013

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

How do I change the battery on my stauer 19093 watch?


The manual is not helpful and neither are any of these other answers. There are TWO batteries in the 19093 Compendium Hybrid. There's a CR2025 on top that runs the digital side, and an SR626SW down below that runs the analog. You need to remove seven small screws holding the upper circuit board to access the tiny SR626SW battery. Be careful of the two brass springs and two contact plates for the pusher buttons, they can fall out. Take pictures at each step of the way, especially when you first remove the back cover.

Jan 12, 2018 | The Watches

1 Answer

Hour, minute and second hands don't work, why?


Yes, there are two batteries in the 19093 (Compendium Hybrid). The first battery (CR2025) is visible as soon as you remove the back cover plate. The CR2025 controls the digital half of the watch and the back light. The second battery is underneath the circuit board that the CR2025 is connected to. There are 6 small screws that will need to be removed to lift the circuit board and gain access to the second battery. The second battery is an SR626SW.

Aug 22, 2014 | Watches

2 Answers

How do I remove a link from the Stauer Colossus Hybrid Chronograph


Removing a link from the wrist band of the Stauer Colossus watch is a task that requires some mechanical talent. The links are held together with pins. These pins need to be pushed out. I strongly recommend the purchase of a "Watch Band Link Pin Remover" (got mine on eBay for $7). Prepared with this tool, the steps are as follows.

a) Separate the wrist band at the position where the strap and latch are held together. Careful! This pin is spring loaded.
b) The links that can be removed are marked with an arrow on the interior side. The pin should be removed in the direction indicated by the arrow.
c) With the previously mentioned tool you will be able to perform the hardest part, namely push out the pin by 3/16". In the image below note how the pushed out pin goes into the groove of the tool.
f72da118-a1b9-4051-8d6c-b43c4f308bd4.jpg
d) Use a small screwdriver or a punch with diameter of less than 0.07" (or 1.8 mm) in order to push out the pin completely (see second picture).
The push pin of the tool can be reversed which is helpful for re-assembly. I recommend smoothing the one end of the pin with a small file or sandpaper. This way the pin enters easily into the hole of the lower section. Else you run the danger of bending the link if the pin is not correctly positioned and you apply too much force.

Oct 24, 2012 | Watches

1 Answer

Watch battery died. Took out and then lost the factory original battery for my Timex Mens 100 Lap Watch Ironman Watch on way to store. Internal parts to watch don't say what battery number I need. You...


I have a 100 lap Timex Ironman Triathlon Flix watch. It uses a CR2025 battery. It is a thin 3 volt lithium battery. My original was a Panasonic battery. I hope that this helps you, Michael

Nov 17, 2010 | Timex Sports Ironman Triathlon 100-Lap...

1 Answer

Stauer watch will not work after battery change.


I have no ideal how old your watch is nor where you had the battery changed. Ideally I would take back to whom changed the battery to see if it was a good battery. If your watch is older it may be time for an adjustment.
Contace Stauer for further assistance at link following:
http://www.stauer.com/customer_service.asp

Good luck.

Aug 21, 2010 | Bulova Watch

1 Answer

How do you reset the time after changing the battery in a stauer 11475 atomic watch??


Take a look at http://www.stauer.com/pdf/17468.pdf
I see that this watch gets it's time signal from Boulder, Colorado so it will only work properly in North America. Perhaps they also do models for the European market - if so I would expect them to work in the same fashion so the manual should still be relevant.

Jul 29, 2010 | Casio Wave Ceptor WVA430A-1AV Wrist Watch

1 Answer

I want to send my atomic stauer watch for repair. Could not set watch when newly received. Where do I send Stauer watch for repair?


To find a registered repair person in your area.
GOTO:
http://www.watch-clock-makers.org/
Hope this tip helps.
r/ David
http://antiqueclock.clockstop.com/

May 12, 2010 | Fossil Watch

1 Answer

Removing Links from the Stauer Atomic Watch band


Click on my profile (escapement), then click on Tips and Tricks. There you will find tip how to add or remove links. Rate me, please .

Apr 08, 2010 | Swiss Stauer Deep Dive Watch

1 Answer

I want to send my atomic stauer watch for repair. Could not set watch when newly received. Where do I send Stauer watch for repair?


Go to "Stauer.com" and at the bottom of the page you will find "customer service".

Click on this and your customer support details will appear.

Mar 20, 2010 | Bulova Watch

1 Answer

My stauer atomic signal watch won't set correct time


Take a look at http://www.stauer.com/pdf/17468.pdf
I see that this watch gets it's time signal from Boulder, Colorado so it will only work properly in North America. Perhaps they also do models for the European market - if so I would expect them to work in the same fashion so the manual should still be relevant.

Aug 08, 2009 | Bulova Watch

Not finding what you are looking for?
Watches Logo

Related Topics:

141 people viewed this question

Ask a Question

Usually answered in minutes!

Top The Watches Experts

D. E. Hev

Level 3 Expert

1187 Answers

 Larry
Larry

Level 2 Expert

126 Answers

vince

Level 3 Expert

1234 Answers

Are you a The Watch Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...