Question about Sharp AR-5320 Black and White Copier

Open Question

What caused the brake sound from fusing unit?

That was after replaced the fusing gear

Posted by on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to replace motor in kitchenaid artisan mixer


Sounds like a worm gear problem to me, it's impossible for the motor (armature) to move far enough to not drive the gear. There are driving pins in the system from fuse gear to paddle.
1) in the fuse gear
2) inside gearbox above planetary joining shaft to bevel gear
3) through planetary and shaft

There is also one joining the little gear inside the planetary to the shaft, doubt you'd break that one though.

Jun 30, 2014 | KitchenAid KSM150PS Artisan Series Stand...

1 Answer

KitchenAid Mixer struggling to spin?


Check everything you have done for a mistake, the pin through the planetary, the pin through the fuse gear and the pin in the main shaft that drives the bevel gear. That's the gear that pinion gear on the fuse gear shaft mates with. After that you are left with a fuse gear fault. I am assuming that the motor is turning at normal speeds and not somehow binding up, no reason why it should as motor stays in one piece during gear changing procedure.

Apr 18, 2014 | KitchenAid Food Mixers

1 Answer

Gear lever stuck in park (P)


Question are you putting in the correct size fuse ? Look in the owners Manuel it will tell you what amp fuse goes where. May be as simple as that always make sure you put the same amp fuse back in very important.

Feb 18, 2014 | Isuzu Cars & Trucks

1 Answer

Error 54 please


Precor Error 54, Target Pulses Lost During Operation Probable Cause 1. Blown F2 fuse.
2. Gear motor wiring is damaged or has intermittent connection.
3. Gear motor is bad.
4. Gear motor target is damaged.
5. Lower PCA is bad.
Corrective Action
  1. Disconnect power from the unit. Remove the F2 fuse from the lower PCA. Using an ohm meter, measure the fuse for 1 ohm or less. If the reading is considerably high, replace the fuse. If the fuse is blown, inspect further for the cause to avoid the fuse blowing again. Inspect for damaged gear motor wiring or a bad gear motor. Replace if necessary.
  2. Thoroughly inspect the gear motor wiring for damage or intermittent connections. Repair or replace damaged wiring or poor connections as necessary.
  3. With unit disconnected from power, disconnect both wires from the gear motor. Using an ohm meter, check for approximately 9 ohms through the gear motor wiring. If the reading is considerably high or low, replace the gear motor.
  4. Inspect the gear motor target for rips, tears, or bad scratches. If any of these are found, replace the target.
  5. During the start up sequence, check the voltage at the gear motor. Voltage should be approximately 12VDC. The voltage should only be present between the time the sequence was started and the error 53 occurred. If the voltage is considerably low or absent and the F2 fuse proved good, replace the lower PCA.
Precor Error Code 54

Nov 02, 2013 | Precor Efx 5.17

1 Answer

Precor error codes 53


Precor Error 53, Can't Read Target, Can't Find Home Switch Probable Cause 1. Blown F2 fuse.
2. Home switch wiring is damaged or has intermittent connection.
3. Gear (elevation/incline) motor wiring is damaged or has intermittent connection.
4. Home switch is bad.
5. Gear (elevation/incline) motor is bad.
6. Gear (elevation/incline) motor target is damaged.
7. Lower PCA is bad.
Corrective Action
  1. Disconnect power from the unit. Remove the F2 fuse from the lower PCA. Using an ohm meter, measure the fuse for 1 ohm or less. If the reading is considerably high, replace the fuse. If the fuse is blown, inspect further for the cause to avoid the fuse blowing again. Inspect for damaged gear motor wiring or a bad gear (elevation/incline) motor. Replace if necessary.
  2. Thoroughly inspect the home switch wiring for damage or intermittent connections. Repair or replace damaged wiring or poor connections as necessary.
  3. Thoroughly inspect the gear (elevation/incline) motor wiring for damage or intermittent connections. Repair or replace damaged wiring or poor connections as necessary.
  4. Ensure the moving arm is away from the home switch and disconnect power from the unit. Disconnect both wires from the home switch. Using an ohm meter, check for approximately 0 ohms. Continue to monitor the home switch resistance and activate the home switch by hand. The reading should change from approximately 0 ohms to open (infinite). If either reading is considerably incorrect, replace the home switch.
  5. With unit disconnected from power, disconnect both wires from the gear (elevation/incline) motor. Using an ohm meter, check for approximately 9 ohms through the gear (elevation/incline) motor wiring. If the reading is considerably high or low, replace the gear motor.
  6. Inspect the gear (elevation/incline) motor target for rips, tears, or bad scratches. If any of these are found, replace the target.
  7. During the start up sequence, check the voltage at the gear (elevation/incline) motor. Voltage should be approximately 12VDC. The voltage should only be present between the time the sequence was started and the error 53 occurred. If the voltage is considerably low or absent and the F2 fuse proved good, replace the lower PCA.
Precor Error Code 53

Nov 02, 2013 | Cars & Trucks

1 Answer

2002 Ford Focus. All of a sudden the gear selector would not move. The button would not push in at all to move out of park. I removed the screw on the neck of the gear selector. It came off and there...


there is a switch that the brake pedal hits when you push it, it releases the selector so you can pull it out of gear, that switch is bad, just look under the dash, push on the brake with your hand and you will see the button im talking about, replace it and its 100% fixed.

Jun 28, 2011 | Ford Focus Cars & Trucks

1 Answer

A fuse on the outside fuse box is buening up and the gears on my transmison r not going through


Good day!


the gears on your transmission not going through because the fuse is burned if you replaced the fuse in the same type,ratings and value..that gear is go back to normal.


Thank you and don't forget to rate my answer.

Jun 10, 2011 | 2000 Mercury Sable

1 Answer

My 4runner blows EFI fuse when putting car in gear ( D or R )


Solenoid valves from transmission gear 1 and 3 needed to be replaced.

regards

Dec 29, 2008 | 2004 Toyota Corolla

2 Answers

Grinding noise


Is the noise comming from the right side of the copier? If so you need the upper fusing roller drive gear. It will break sooner then later.

Feb 08, 2008 | Sharp AL-1641CS Laser Digital Copier

Not finding what you are looking for?
Sharp AR-5320 Black and White Copier Logo

Related Topics:

44 people viewed this question

Ask a Question

Usually answered in minutes!

Top Sharp Office Equipment & Supplies Experts

Anthony Karuku

Level 2 Expert

268 Answers

amir hamza
amir hamza

Level 2 Expert

318 Answers

k24674

Level 3 Expert

8081 Answers

Are you a Sharp Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...