Question about Asko Washing Machines

1 Answer

Are you able to tell me the specification of the bearings for the motor of an Asko 10505 washer?

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Asko Master
  • 54,386 Answers

No, Fixya cannot

Posted on Mar 23, 2018

Ad

5 Suggested Answers

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Anonymous

  • 49 Answers

SOURCE: asko 10505 - wash finished, door won't open

it is most likely your machine may have a draining problem. if it cant drain the water out the door wont open. if you open the small door at the front bottom of the machine you will find the little black drain hose. unplug the hose off the door and drain machine. when the machine is empty try powering on and opening the door. if still no luck you will see (in the same location) a red pull ring. undo the screw holding the ring in position and gently pull until the door releases. it would be worth undoing the button trap lid to access the pump and check for any blockages (most common coins **** pins etc) let me know how you get on.

Posted on Mar 06, 2008

Anonymous

  • 1 Answer

SOURCE: repair front load washer

wash machine not draining properly at end of wash. not fully spinning.
pls advise

Posted on Sep 11, 2008

Macmarkus

Mark MacDonald

  • 2605 Answers

SOURCE: asko 10505 washer will not spin

Hi, 2 things to check for. Obstruction in the drain pump or faulty drain pump, brushes in the motor worn out. The easiest way to determine the pump issue is answer this question. Does it drain ? Next, turn the timer to the drain/spin cycle, obviously it should drain & spin and advance to "off". The next thing with these 10505 asko is to see if the drum rotates in both directions in the wash/agitate portion of the cycle. You can just select the short wash for this (I forget if it's #4 or #5) If not, it's worn brushes. However, you'll have to make sure the armature isn't damaged before simply installimg new brushes. We can cross that bridge when we get there. Let me know. Hope that helps, though those are just the most common problems there could be others. Good Luck

Posted on Nov 01, 2009

John John

  • 32 Answers

SOURCE: i have an asko 10505 washer. how do you open the

here is a video that shows someone closing an Asko machine. I think you just have to get your hand in that place where she shuts the door and pull.

http://www.youtube.com/watch?v=kmvxNwqUDJ8

Posted on Mar 28, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Asko 10505 Washer will drain but will not spin. Initially that was the problem, but then in trying it out again the washer will fill with water, will drain but will not even wash now. Do you think it is...


You don't mention if the drum spins if you choose the spin program, if it doesn't it could be the brushes on the motor. This would be a cheaper option to try first rather than a board. sometimes you can clean the com or tap the brush carriers gently and get the motor to spin on an empty or small load.

If you're confident, with the power offer and machine isolated you can check the resistance across both the brushes and slowly rotate the motor as a test.
hope this helps

Mar 12, 2013 | Asko Washing Machines

3 Answers

I have an asko 10505 washer. how do you open the door?


here is a video that shows someone closing an Asko machine. I think you just have to get your hand in that place where she shuts the door and pull.

http://www.youtube.com/watch?v=kmvxNwqUDJ8

Mar 28, 2011 | Asko W6021 Front Load Washer

1 Answer

Unable to locate any info on a model 10505 se # 982410041588


Hi, I may be mistaken but I don't think so, that number ( 10505 ) is for an Asko washer built in 1998, not a dishwasher. Do you require assistance with your washer ? I will watch for your reply. Macmarkus :)

Mar 17, 2010 | Asko Dishwashers

1 Answer

Asko 10505 will not spin the belt is not broken, tub fills and drains


Your washer unit is needing a new timer and replacement is needed if the part is available.
This will require some electrical experience to replace the timer unit or go to your local Sears repair and they will come out and repair your unit for a fee.

Jan 29, 2010 | Asko Washing Machines

2 Answers

Replacing Motor Brushes, what needs to be done to clean commutator for a Asko 10505 Washing Machine sold in Australia - purchased around 1998 - ignore the W6021 system wouldn't let me post.


To clean the commutator, or armature as it is usually called, simply rub it with a piece of emery paper, or sandpaper, turning it by hand to ensure you clean it properly..
You need to remove the motor to do this of course.
Please rate my solution.
Thanks.

Nov 12, 2009 | Asko W6021 Front Load Washer

1 Answer

Asko 10505 washer will not spin


Hi, 2 things to check for. Obstruction in the drain pump or faulty drain pump, brushes in the motor worn out. The easiest way to determine the pump issue is answer this question. Does it drain ? Next, turn the timer to the drain/spin cycle, obviously it should drain & spin and advance to "off". The next thing with these 10505 asko is to see if the drum rotates in both directions in the wash/agitate portion of the cycle. You can just select the short wash for this (I forget if it's #4 or #5) If not, it's worn brushes. However, you'll have to make sure the armature isn't damaged before simply installimg new brushes. We can cross that bridge when we get there. Let me know. Hope that helps, though those are just the most common problems there could be others. Good Luck

Nov 01, 2009 | Asko W6021 Front Load Washer

1 Answer

Leaking inlet valve on Asko 10505


Unfortunately, the only way to be 100% sure this won't happen again is to replace the inlet water valve. Especially if the problem is intermittent. You could live with it if you turn off your water taps when the machine is not in use.

Feb 19, 2009 | Asko W6021 Front Load Washer

2 Answers

Repair front load washer


wash machine not draining properly at end of wash. not fully spinning.
pls advise

Sep 11, 2008 | Washing Machines

1 Answer

Asko 7005 and washer 10505


1) there is a reset button on the back panel of you dryer it is in the middle black rubber...

2) you really can't the asko washer needs a 240v to run... You can hire an licenced electrician to wire a 240v plug for your asko washer if you do not want to plug it into the dryer

Jul 01, 2008 | Asko W6021 Front Load Washer

Not finding what you are looking for?
Washing Machines Logo

Related Topics:

37 people viewed this question

Ask a Question

Usually answered in minutes!

Top Asko Washing Machines Experts

Gerry Harvey
Gerry Harvey

Level 3 Expert

1481 Answers

Joseph Hoffmann

Level 3 Expert

1755 Answers

ROB

Level 3 Expert

858 Answers

Are you an Asko Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...