Question about Ice Kitchen Appliances - Others
Uline clr60b won’t stop making ice. I have replaced bin thermostat and still won’t stop making ice. To install you install probe all the way to end(that is in ice maker)? Or did I install incorrect ? Ice thickness is not set to thick. I installed bin thermostat probe all the way to end of bar that is inside ice maker. Help!
Http://www.aramislashes.com/wholesale-mink-eyelashes/wholesale mink eyelashes WHOLESALE MINK EYELASHES MANUFACTURER-ARAMIS LASHES Our wholesale mink eyelashes is more lighter,softer and more Flexible, our 10 year's experience in wholesale mink eyelashes can bring you more hot fashionable mink lashes, you can get top quality from our lashes factory with fast delivery. Most luxury package wholesale mink eyelashes box is available.
Posted on May 08, 2018
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
Here's a link to this great service
Posted on Jan 02, 2017
SOURCE: Thin Ice on Whirpool Ice Maker
If The ice maker has completely stopped producing ice Check to see whether the ice maker has been turned off. Here's how to check. Look for a wire along the right side of the ice maker that looks a bit like a coat hanger. If this wire is in the raised position, the ice maker is turned off. On some units you simply lower the wire to the down position to turn the ice maker on. On others, you lower a small red plastic lever to lower the wire. If the wire is in the proper position check the freezer temperature, it should be between 0-8 degrees Fahranheit. If it is warmer than 10-12 degrees, the ice maker may not produce any ice. Check your door seals and thermostat, repair/replace as necessary.
The ice maker is producing ice poorly When an ice maker is producing ice poorly--when it produces just a few cubes or none, or when the cubes are too small--it's usually because of a clogged water line or a defective water inlet valve.
First, check the water line attached to the back of the refrigerator for good water flow. To do that, first turn off the water supply valve. Then remove the water line from the back of the refrigerator. Next, place the water line into a bucket and momentarily turn the water valve back on to test the flow. If the flow is poor, you need to repair, clean, or replace the tubing or the shut-off valve that supplies the water. If the flow is good, you may have to replace the water inlet valve.
Please do rate the solution as "FixYa" if found useful and revert for further assistance.
Posted on Apr 05, 2009
U-line does make compressors as long as its not a r12 system. As far as the icemachine turn breaker off for a couple of min then try it. If same results then it could be a board.
Posted on May 15, 2009
First thing is to remove the water from the trough. Pull out the grey standpipe in the back of water trough. Then see if the grid has a good frost pattern.If the frost pattern is NOT even then you need a service call to check the sealed system. If you do have a frost pattern check to see if the water is splashing over or make sure the drain is in the bin drain hole.If water is getting in the bin then the ice can melt as fast as it makes it.Make sure your cleaning with U-line cleaner.
Posted on May 28, 2009
Tips for a great answer:
Jan 17, 2014 | U-Line Icemaker
Oct 30, 2012 | U-Line Uline Origins Series...
Jul 19, 2009 | U-Line Uline Origins Series...
May 04, 2009 | U-Line Icemaker
Dec 23, 2008 | U-Line Icemaker
Nov 23, 2008 | Hoshizaki AM-50BAE Drain Pump Kit
Nov 04, 2008 | U-Line Icemaker
90 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: