Question about Ricoh Office Equipment & Supplies

1 Answer

My Ricoh MP C2050 machine is showing error functional problems detected turn main power switch off then on. if appears again;please call service SC865-01 on start up. Serial No.of machine V2293901308

Posted by Anonymous on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    MVP:

    An expert that got 5 achievements.

    Habit-Forming:

    Visited the website for 3 consecutive days.

    New Friend:

    An expert that has 1 follower.

  • Contributor
  • 29 Answers

An error is detected while operating the HDD and u have to replace

Posted on May 08, 2019

Ad

6 Suggested Answers

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Anonymous

  • 78 Answers

SOURCE: Ricoh Aficio 1018 photocopier

For the Aficio 1018. SC-320 is laser failure - the polygon mirror motor inside the laser has failed and needs replacing. You will need to contact your nearest service agent for repair.

For your RICOH Aficio 1013F - SC-551 is overheat in standby mode as far as I can tell. The circuitry that controls the fuser section ie manages the heat has problem. Unless its right near a source of heat like a heater or has no circulation around you machine you will need contact a repair agent for this machine also.

Posted on Mar 19, 2008

Anonymous

  • 6 Answers

SOURCE: ERROR CODE SC101

SC101 indicates and exposure lamp problem. To try and correct, turn OFF the copier and then unplug from the wall. Wait 10 seconds and plug it back into the wall, then turn on the copier. Watch to see if the exposure lamp comes on - lift the document handler if you want. If the exposure lamp is working correctly, the scanner will briefly move to the right and the light will turn on then off after it moves to the left.

Posted on Jul 09, 2008

Everett Lin

  • 990 Answers

SOURCE: Ricoh Aficio 2027, Service Code 320

dear sir; the error code 320 on ricoh af 2027 it's means laser polygon motor problem, the laser unit right under the toner unit, litlle bit left. some error code can be reset why don't give them a try
1, power on the machine
2, press "clear mode"( has the c in a diamond), "107"then press and hold down "clear/stop" key
3,turn power off 10 second later back on.
I f reset doesn't work, you need to replace laser motor. thank you
HAVE A HAPPY HOLIDAY

Posted on Dec 17, 2008

santosj27

santosj27

  • 263 Answers

SOURCE: I have a ricoh 2051

After turn the main switch off and on the error appears again????
This error means that there is a bad comunication between the controller board and the operation panel.
Did you intervew in the machine? Some tecnical intervewing?

Posted on Feb 17, 2011

gggg

  • 904 Answers

SOURCE: Hello! I have same problem with Ricoh MP2050.

On a C2050 copier, sc400 is an ID sensor error. The ID sensors detect image density, and they probably either need to be cleaned or replaced.

Posted on Mar 22, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to fix colour position in ricoh c2050


tthe machine can do autocalibrattion,
see the video

Oct 05, 2015 | Ricoh Compatible 4 Color Set Aficio MP...

1 Answer

I have an error on my gestetner mp c2030 with code sc222, please help me.


Problem with the yellow laser unit. Probably need a tech for that one.

May 20, 2014 | Ricoh Compatible 4 Color Set Aficio MP...

3 Answers

Error occured SC:302 Functional Problem Turn main power switch off and on if the error appears again. Call Service


SC:302
Charge roller current leak

Symptom: A current leak signal for the charge roller is detected.
Possible Cause:
?? Charge roller damaged
?? High voltage supply board defective
?? Poor connection of the PCU

May 27, 2011 | Ricoh Aficio MP 1600L Black and White...

1 Answer

I have a ricoh 2051 with this error message: Functional problem within the machine. Turn main power switch off and then on. if the error appears again, then call Here is the error message code: SC...


After turn the main switch off and on the error appears again????
This error means that there is a bad comunication between the controller board and the operation panel.
Did you intervew in the machine? Some tecnical intervewing?

Feb 17, 2011 | Ricoh Aficio 1035 Copier

1 Answer

Service SC 990 RICOH Aficio 551


sc990 is a general software error. It could be caused by a specific application or function, or it could be caused by a problem with the process control. In general, you can get rid of the sc990 error by turning the machine off with the main power switch (the orange switch on the left side of the copier) but if the error comes right back, the best first solution is to update the machine's firmware.

Nov 18, 2010 | Ricoh Aficio MP 1600 Black and White...

1 Answer

Eror sc547


The error sc 547 refers to a "Zero cross signal malfunction".

This means that the applied power supply AC frequency was detected at over 66Hz or below 45Hz, and the zero cross signals are not detected within a certain period within 500 ms after the main power switch has been turned on.

Possible causes are:
- Power supply board defective
- IOCSS defective
- BICU defective

Try to reset the SC code by entering SP5810 and select 1.
Then hold down the photo mode key and the # key at the same time for at least 3 second.
Then turn the machine off and on again.
If the same issue still appears, try to replace the Power Supply Unit.

Jul 04, 2010 | Ricoh Aficio MP 2000 Black and White...

3 Answers

I need solution to aficio 200 error code sc322


sc322 is a Laser synchronization error:

Means that the laser synchronization signal cannot be detected by the main scan detector board.
Possible causes:
Poor connection of the interface harness which connects the laser synchronization detector board and the BiCU board.

Laser synchronization detector board out of position or is defective.
BiCU board is defective.

Unfortunately,unit needs service.
If I could be of further assistance, let me know. If this helps or solves the issue, please rate it.
Thanks, Joe



I’m happy to assist further over the phone at https://www.6ya.com/expert/joe_8b8c2cd6ce148309

Apr 19, 2009 | Ricoh Aficio 180 Laser Printer

Not finding what you are looking for?

Open Questions:

Office Equipment & Supplies Logo

Related Topics:

219 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ricoh Office Equipment & Supplies Experts

gggg

Level 3 Expert

904 Answers

Adorjani Laszlo

Level 3 Expert

1316 Answers

quennie732

Level 2 Expert

422 Answers

Are you a Ricoh Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...