Question about Hitachi Televison & Video

Open Question

The lights turn on my hitachi magic wand but it will not actually vibrate and turn on

Posted by on

Ad

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
  • 1 Answer

SOURCE: Sounds like its working, but nothing happens

I had the same problem with mine, it's due to the fact that the smaller spring has become un-lodged from the ******** itself.

You will need:
1. Roll of electrical tape.
2. Utility Knife
3. A small slot head screw driver OR a pair of needle nose pliers.

The solution is to unscrew the silver ring so that is can be moved up and down. Now, you need to use a utility knife and cut the blue rubber off of the spring. Once you have the blue rubber but off you can see a large spring with another smaller spring inside. Push the head of the ******** till the larger spring's coils are an 1/8 to 1/4 of an inch apart. Next take either the small slot head screw driver or a pair of needle nose and jam the smaller spring back into the hole in the center of the white plastic piece inside of the larger ring. Next plug it in to make sure the vibration is working, reattach the silver piece and tape the larger spring with electric tape.

Posted on Oct 28, 2008

Ad
  • 1 Answer

SOURCE: I fixed my hitachi magic

rotate the head/neck part, one of the sides is not aligned with the notches in the bace of the neck. rotate it to fit right then you should be able to fit it on easily

Posted on Jul 25, 2012

alicantecoli
  • 22484 Answers

SOURCE: My magic wand powers on but the head does not vibrate. If I push down hard on the head, it vibrates as it should. But, when I let go, it does not vibrate. Any suggestions?

No idea ,sounds like you have worn out the plastic drive piece ,so i would humbly suggest that you do as the previous expert suggested

Posted on Feb 02, 2015

rgall3285
  • 64259 Answers

SOURCE: The small spring in the head of my hitachi magic wand is broken. How can I remove it to take it to the hardware store & replace it?

I have a doctors tool called forceps that work wonderfully for grasping small parts . check the sporting goods department at walmart .

Posted on May 27, 2015

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

3 Answers

I fixed my hitachi magic wand, but now I cannot get the silver ring back on during the final steps of reassembly


rotate the head/neck part, one of the sides is not aligned with the notches in the bace of the neck. rotate it to fit right then you should be able to fit it on easily

Jul 16, 2011 | Hitachi Magic Wand Hv250r Hand Held...

1 Answer

It seems to have power going thru it..but no vibration...help


The small sping has come out of the shaft from the motor.If you open the unit you will see that the motor has a little impeller and a shaft with a slot in it. The little spring inside of the massager head is suppose to ride inside of that motor shaft with the little tab on the spring lining up in the slot. It's really flimsy and after I fixed mine it fell out again after 5 minutes of use. It needed a stiffer spring or a different way of engaging the motor shaft. I'm still working on this...

Apr 09, 2011 | Hitachi Magic Wand Hv250r Hand Held...

2 Answers

Can the Magic Wand Rechargeable Massager be charged from a 220 volt power?


If your wand is N American then "don't do it" 220 through a 110/120 will fry all the magic out of it. You could get a step down transformer 220 to 110. Plug that into the 220 socket and plug your magic wand charger into that.

The cost would not be worth it though ... buy some more magic that is 220. be happy ... not sorry :-)

Nov 17, 2009 | Hitachi Rechargeable Wireless Magic Wand...

2 Answers

Sounds like its working, but nothing happens


I had the same problem with mine, it's due to the fact that the smaller spring has become un-lodged from the ******** itself.

You will need:
1. Roll of electrical tape.
2. Utility Knife
3. A small slot head screw driver OR a pair of needle nose pliers.

The solution is to unscrew the silver ring so that is can be moved up and down. Now, you need to use a utility knife and cut the blue rubber off of the spring. Once you have the blue rubber but off you can see a large spring with another smaller spring inside. Push the head of the ******** till the larger spring's coils are an 1/8 to 1/4 of an inch apart. Next take either the small slot head screw driver or a pair of needle nose and jam the smaller spring back into the hole in the center of the white plastic piece inside of the larger ring. Next plug it in to make sure the vibration is working, reattach the silver piece and tape the larger spring with electric tape.

Oct 25, 2008 | Hitachi Magic Wand Hv250r Hand Held...

1 Answer

Saeco Magic squirts water out the wand when brewing


Hi Steve,

You have to replace the gasket on the steam pin, maybe you have to replace the steam pin to if it is worn.

Apr 11, 2008 | Saeco Magic Cappuccino Espresso&Cappuccino...

Not finding what you are looking for?
Televison & Video Logo

Related Topics:

90 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hitachi Televison & Video Experts

Jaime Hernandez

Level 3 Expert

2337 Answers

The Knight
The Knight

Level 3 Expert

76140 Answers

Steve Allison
Steve Allison

Level 3 Expert

5569 Answers

Are you a Hitachi Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...