Question about Dishwashers

Open Question

Have a DD24D Fisher&Paykel dishwasher. When it is turned on, it does not give an error code, but gives 4 quick beeps and then shuts off. When is it telling me?

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
jsrock516
  • 5911 Answers

SOURCE: dishwasher f1 problem on fisher paykel

All the information that I have found about this particular problem indicates that the "F1" error is a flood or overflow alarm. It's generally caused by a clog in the drain line and/or tub not sealing properly when closed.

If this is a drawer style dishwasher there is a lid in the equipment cabinet that must seat properly on the drawer when it is closed. If you place items in the dishwasher that are too tall for the drawer lid to seat properly, it will not seal and water will splash over the sides of the tub during the wash cycle.

Another common problem is a clogged or kinked drain line. Remove the drain hose and make sure it is not plugged. Check it at BOTH ends.

The alarm is activated by a float switch in the bottom tray of the dishwasher. Look to see if this is any standing water in the bottom tray. If there is any water, or signs of wetness, the alarm will not clear until it is dried out. I found a couple of recommendations to clear the alarm. The first involved removing the dishwasher from where it is installed and tilting it at a 45 degree angle to pour any standing water out. Another method is to dry the bottom out with towels as best you can, and then use a hair dryer to dry any residual water. I hope I'm on the right track with this and I hope this solves your problem. Post back if you have any further questions.

CAUTION: UNPLUG the dishwasher or turn off the breaker BEFORE servicing inside the cabinet.

Posted on Feb 20, 2008

Ad
  • 351 Answers

SOURCE: fisher & paykel Nautilus dishwasher

pull the dishwasher out and push down on the top of the dishwasher were the door latch is ,its not making conntact with the microswitch.but you could also have a broken handle.these are both common faults on this model.hope this helps.

Posted on Mar 20, 2008

  • 28 Answers

SOURCE: Fisher & Paykel Washing Machine IWL12

130 rotary position switch fault 136 motor fault

Posted on Jun 21, 2008

  • 3230 Answers

SOURCE: Fisher & Paykel dishwasher model dd602 error code F4

Hi there,
It means your filter is dirty. Remove metal plate at bottom & scrub with a toothbrush. Clean arms as well.
Clean all around the door & pull out the lift out filter, scrub clean with a toothbrush.

Posted on Jun 26, 2009

jyackle5
  • 8197 Answers

SOURCE: Fisher and Paykel dishwasher DD603 manual

You can get the manual below for free..

http://www.fisherpaykel.com/admin/pdfs/pdf_usecares/527971B_DD_user_guide_USw.pdf

Good Luck and please rate 4 thumbs for the free answer

Posted on May 15, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Machine beeps 3times when we go to start it, no lights or error codes show up.


Not sure exactly which model dishwasher you have. Most likely the error is due to door not shutting properly which overrides the start.

Jan 08, 2014 | Fisher and Paykel Dishwashers

1 Answer

F1 error on Fisher and Paykel Dish Drawer


Sorry did not see your problem report earlier. If you have checked the sensor under the bottom drawer and it is dry, then F1 is caused by top drawer power filter fault. This means the bottom drawer controller is giving the F1 error but the top drawer controller has no power. Can you confirm this.

Apr 08, 2013 | Fisher and Paykel 23 in. DD-603SS Built-in...

1 Answer

Can the beeping alarm be turned off?


usually if you turn the power off and on after a short delay the beep should go away. But the alarm fault code will keep showing on the display / drawer panel light until fault is fixed.

Hope this helps.

Feb 03, 2010 | Fisher and Paykel 23 in. DD-603SS Built-in...

2 Answers

Hi Both drawers show error F1 flashing beeping with rinse light on and both pumps run after power is applied to machine


F1 error indicates flood switch in base has activated, meaning machine has leaked. This causes machine to drain continously, and can only be stopped by switching off power. Not easy to fix if you don't have experience- bottom drawer has to be removed to access flood switch, then machine needs to be test run and checked for leaks. Best to call the professionals!!

Oct 03, 2009 | Fisher and Paykel 23 in. DD603H SS...

2 Answers

F 1 Error, blinking, beeping and will not stop even when turned off, so we had to turn the circuit breaker off to stop the noise.


You have a leak.
Either from the top lid seal or bottom lid seal. A s time goes by the water level activates the sensor causing the beep. It won't do anything until you fix the leak.

May 25, 2009 | Fisher and Paykel 23 in. DD-603SS Built-in...

1 Answer

Error code. Fisher and Paykel Dishwasher


well since you asked on the 5th July, and no reply, doesnt look like you may get one. I thought thats what this site was about??

Jul 05, 2008 | Dishwashers

1 Answer

Fisher & Paykel Washing Machine IWL12


130 rotary position switch fault 136 motor fault

Apr 29, 2008 | Fisher and Paykel Fisher Paykel Intuitive...

1 Answer

Fisher Paykel Dishwasher Door Open error code


If it is a dish drawer type there is a clip at the rear of the drawer that holds the drawer closed. you will need to withdraw the drawer partially to look in. with the drawer open the fingers should be facing towards you. If not you will need to reach in and pull the top of the fingers towards the front. there is a replacement arm that holds the pipes and cables away from this part.

Nov 18, 2007 | Fisher and Paykel 24 in. DD603H W Built-in...

Not finding what you are looking for?
Dishwashers Logo

Related Topics:

20 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dishwashers Experts

Mike

Level 3 Expert

4356 Answers

Marvin
Marvin

Level 3 Expert

83850 Answers

Brad Brown

Level 3 Expert

17816 Answers

Are you a Dishwasher Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...