Question about Office Equipment & Supplies

Open Question

I still have not found solutions to my HP1040 fax. It will not print anything. New cartridge went through all verification steps. nothing

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
checkitright
  • 1362 Answers

SOURCE: the fax will not print anything

2 possibilities

1- you did not remove the plastic film on the cartridge
2- the printhead has dried up

Posted on Dec 06, 2007

Ad
  • 12 Answers

SOURCE: black cartridge not printing

This is what worked (so far) with my Dell1.gif AIO A940 printer1.gif that wouldn't print black ink.

It worked for awhile when I chose photo/glossy paper, but then it quit printing again (see below).

PRINT, PROPERTIES, PAPER SETUP, SPECIALTY PAPER, PHOTO/GLOSSY


I got it to print, again, by putting SEVERAL papers in the feeder (instead of just 1) - there is a sensor that is supposed to automatically detect paper type, and it might not be working right, especially with one or only a couple of sheets.

Posted on Feb 02, 2008

SOURCE: Samsung SF560.

make sure you have the correct cartridge as the SF560 & SF560R use different cartridges

Posted on Apr 30, 2008

  • 96 Answers

SOURCE: Kodak EASYSHARE 5500 will not print with black ink

Here are the things you will be asked to try if you call support. They may fix the problems as well. Taking the printhead out and putting it back in is the big helper.

Remove the black and color ink cartridges.
Right above where the black ink cartridge was, in the top left hand corner of the printhead, push up towards the ceiling and you should be able to push a button that releases the printhead.
Place the printhead right back into the printer and push straight back on the back wall.
You should hear a loud snap.
Replace the ink cartridges which should snap as well.
Close the printer.
After about a minute or so the printer will ask you to do a calibration.
Insert a paper and press start.
Scan the calibration sheet.
After that, in the menu, do a printhead clean.
(If this is a 5100, do it in the home center ->? in the top right ->Maintainence ->Clean Printhead.)
Do one basic and one deep.
Print a demo sheet to see if anything has changed.
If the picture looks better, continue to do cleans.
In the event that it does not, the printhead will need to be replaced and since the printer is still under warranty, Kodak specialists will try to overnight you a printhead.
The whole process is short and free.
The number for Kodak AiO Support is 1 800 421 6699.

Posted on Aug 19, 2008

debroy
  • 174 Answers

SOURCE: Canon MP 210 gives E5 error and will not print.

disconnect the power and usb cable from the back of the printer and press and hold down the
power button for 30 sec and then reconnect the cables and try again...open the backdoor and
try to move the rollers in upward direction.Make sure the unit is connected directly to the
walljack.

Posted on Nov 27, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Fax will not print: I connected the fax machine and plugged it in. It sends faxes OK. When a fax is sent to it, nothing comes out. The sending fax doesn't receive an error message, seems like all went...


Does the machine print anything? such as a directory or print when making a copy? I rather suspect it does not. When an incoming fax is recvd does the paper get pulled in and come out blank? If so your problem is with printing (or lack of it). Perform head cleaning. Also make sure the black cartridge still does not have its deal stuck on it. Post again if you still have problem.

May 05, 2011 | Brother Multi-Function Center MFC-3360c...

1 Answer

How do I align the cartridge after I replace it. The fax printed out a sheet and the lines are not straight. I went to tools...to align cartridge and then I am not sure how to adjust the lines


Hi,

Follow below steps to complete alignment.

  • With the Cartridge compartment cover open, insert the print cartridge into the print cartridge cradle with the contacts facing into the unit. When the cartridge is seated in the print cartridge cradle, push the top of the cartridge towards the back of the unit until the print cartridge clicks into place.
  • Close the cartridge compartment cover and control panel.
  • Press the Start/Enter button.
  • On the keypad, press 1 if the replacement print cartridge is new or 2 if the replacement print cartridge is old
NOTE: When you put in a new cartridge, you must choose 1: New .When you put in a used cartridge, choose 2: Used . This helps you to check the correct amount of ink you have left.
  • An alignment page will print and 06 [01-11] will show on the display
  • Look at the alignment page and select the number under the straightest line, and then press that number on the keypad and then press Start/Enter .

Oct 17, 2010 | HP 1040 Plain Paper Inkjet Fax

1 Answer

Fax will not print after installation of new cartridge


Look at your NEW print cartridge again, very carefully. I'll bet there's another piece of tape on the bottom of it. That's what happened to me.

Dec 03, 2008 | Sharp UX B700 Plain Paper Inkjet Fax

1 Answer

New cartridge; now won't print any document, fax or copy


It is not impossible to get a brand new bad ink cartridge. I've seen lots of bad ones.

Oct 04, 2008 | Sharp UX B700 Plain Paper Inkjet Fax

2 Answers

Nothing there


Did you try cleaning the print cartridge nozzles.

Press Function once and up arrow 2 times
Press the right arrow once and the up arrow once
Press the right arrow once
Press Start/Memory button
It will print a test parttern page

Once you insert the new cartridge did the machine recognize the new cartridge? You had to press 1 for new

When 1 is selected you will get a prompt New Cart: OK?
OK press start.

If you selected NEW the display will show the alternating messages at right. Align Cartridge----1 Print 2 Set

Press 1 to print an alignment page

Hopefully, it will printed. Let me know one way or the other.

Mar 27, 2008 | Sharp INKJET FAX UX-A1000

1 Answer

Machine not printing


try to go a setup and option clean the cartridge

Nov 21, 2007 | HP 1040 Plain Paper Inkjet Fax

2 Answers

Cannot receive faxes or do copies


If you still have your old cartridge reinstall it that will tell you if it is the cartridge or not. If you still have the problem,it could be the encoder.

Oct 23, 2007 | Office Equipment & Supplies

Not finding what you are looking for?

Open Questions:

0 Answers

My Ricoh 3035 / Savin 8035 prints uniformly light pages, and tells me to add toner, with a FULL toner bottle. The developer unit itself is completely packed with toner. There are no other errors set. The issue described is recent, within the last 500 copies. Prior to that this machine was running perfectly. I've had this copier for a couple of years. It was used. It NOW has 617,871 prints/copies/faxes as of today. I replaced the developer unit remanufactured and new developer at 591,810. The transfer belt and cleaning blade are new at 607,638. I replaced the PCU with a completely remanufactured unit at 607,688. The fuser was replaced with remanufactured unit also at 607,688. I was STILL having some issues with bad quality copies, so I narrowed the matter down to a defective drum in the remanufactured PCU. I replaced the drum, and at THAT time, I installed every part in the Savin Maintenance Kit PMB082150K, which I previously received with the copier. I also replaced the PCU Entrance Seal and tape the long mylar one at the top of the drum. When I installed the developer unit, I initialized the settings, pursuant to the Service Manual, and the same with the drum, and the appropriate one each time I previously cleaned the ID Sensor Today, I went through the trouble of replacing the ID Sensor, initialized the same, and it made no difference. The copier has run just fine for the last couple of months, and then as I stated in the question, about 500 copies ago, all of the copies suddenly became light. No, it's not the density setting. I've done everything except do a factory reset. Incidentally, I have the Ricoh 3035 Service Manual, and also the Parts Manual. Experientially, the only computers I have ever purchased are 2 of them, for my office, in 10 years. Other than that, I have built every computer I've ever made, from parts. As far as this copier, I have done the copier maintenance, per the maintenance schedule, myself, and when it appears that maintenance needs to be done. This problem however, is driving me nuts. As I said, the only symptoms of the light copies are that add toner light that comes on periodically, and toner absolutely packed into the developer unit entrance such that its spills out when I remove the PCU. One last thing, and this is an when all else fails kind of thing: since the toner bottle is full, I open the front door, and using a channellock, I fix the add toner problem by rapping very lightly on the end of the PCU, and the developer unit! This DOES fix the toner out problem every time, but it does NOT fix the light copies. Simply opening the door, sliding the toner carrier out, putting it back, and then closing the door, and repeating that process a couple of times sometimes also works.

Jan 21, 2019 | Ricoh Aficio 3035 Digital...

Office Equipment & Supplies Logo

Related Topics:

27 people viewed this question

Ask a Question

Usually answered in minutes!

Top Office Equipment & Supplies Experts

k24674

Level 3 Expert

8080 Answers

Cindy Wells

Level 3 Expert

5725 Answers

Marvin
Marvin

Level 3 Expert

83850 Answers

Are you an Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...