Question about Dometic Refrigerators

1 Answer

Error 51 flashing not starting on gas dometic 3way has automatic mode

If voltage to ignitor bad ignitor if not sparking if no voltage to ignitor bad control board

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Dometic Master
  • 10,033 Answers

If voltage to ignitor bad ignitor if not sparking if no voltage to ignitor bad control board

Posted on Apr 30, 2019

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
Therinnaiguy
  • 1420 Answers

SOURCE: Goodman GMP075-3 ignition problem

OK, if the furnace is not lighting for even a few seconds, you have either a bad gas valve, bad wire, bad control module or no gas. The pressure switch is not the issue. Check all wires to the gas valve and look for 24 volts across them when the ignitor glows and you hear the click. Then test for 24 volts to ground. It could be a bad ground wire.

Posted on Oct 21, 2008

  • 6 Answers

SOURCE: Goodman GMP075-3 ignition problem

bad board,i have had several board failures on goodman

Posted on Dec 31, 2008

  • 1 Answer

SOURCE: Thermador Gas Range - Griddle ignition will not spark

I have a Thermador Gas Range PG364GDBS - Oven, 4 burners, and center griddle. All are gas. The four burners and gas oven work fine. The griddle just stopped working, no spark. Turning on the griddle control, the gas valve opens(hear it), gas flows (smell it), but the ignitor will not spark (no loud or faint spark that I can hear). I got a replacement ignition device (mount at the burner) thinking it might be the problem, but still no spark. I checked the AC voltage at the terminal and measured 39 VAC between the terminal and ground. Not sure if that is the correct voltage. Any insights or advice would be great.

Posted on Dec 10, 2009

  • 1 Answer

SOURCE: Goodman GMP075-3 ignition problem

Goodman gmp075-3 gas furnace and the flame cycles for 4 sec

Posted on Dec 11, 2009

kel1guy2002
  • 3740 Answers

SOURCE: Dometic RM3801. Propane ignition failure.

The older units has a 3 VDC glow coil the newer units have a 12VDC igniter.

Fromwhat your described above the next paragragh is your ignition system.

The igniter control voltages in the newer SPARK type igniters are (+) = 12VDC, (L)= high voltage lead (Spark plug voltage! I.e ruin your meter type voltage), (-)= Ground L is the lead that passes the HV spark from the control unit to the ignitor plate. The L lead should pass one heck of a hit if is workng correctly.
If not look at the HV lead to see if it is grounding out somewhere.

If the gas safety valve is not sensing gas pressure... you will not have 12VDC to the + terminal of the ignition moudule.

With the gas on and you have 12VDC at the ignition module + terminal then most likely the ignition module is bad.


Kelly


Posted on Apr 17, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have freightliner 2017 dometic fridge is trying to start but wont


check gas line to ignitor if ok check ignitor if no gas board if voltage to gas valve bad valve

May 20, 2018 | Dometic Refrigerators

2 Answers

Dometic rm2652 re-ignitor


Dear sir/madam,

Turn the refrigerator off and remove the wire
between the electrode and igniter. Now turn the
refrigerator to the gas mode. If no internal
clicking sound is heard the igniter is defective.
It is important to remove the high voltage wire
that goes to the electrode from the igniter when
you are checking the igniter for operation. The
high voltage wire and the electrode can be
shorted to ground causing the igniter reigniter
to think that the flame is lit, resulting in no
spark on gas operation.

thanks
good luck

Sep 14, 2008 | Dometic RM2652 Refrigerator

1 Answer

Dometic rm 2807 igniter won't spark


if lines clean to ignitor and wont spark see if voltage to ignitor if voltage bad ignitor if no voltage bad board

Jul 11, 2014 | Dometic RM2652 Refrigerator

1 Answer

Hi I have a Rinnai 100f Space Heater. Found it with a blinking red light.. Whe I shut it off to restart it. It restart by hearing the combumsion fan start up then go off with error code 53. Manual says...


Could be one or several issues here.Here is how system works first the combustion motor started then pressure switch closes (that's the part with the small hose connect to ),make sure all exhause is clear. Now when that closes and all safety ok then gas valve open then furnace ignite.
If you have 24 volt to gas valve and could hear valve open (a clicking soind) and no ignition then you have a ignitor issue .if it's a glow type ignitor it should glow ,if not replaced .If it's a spark ignitor you should be to hear it sparking .Normally a spark ignitor will have a orange hose going to it .Trace orange hose back to board and disconnect from board then check for voltage from metal pin that hose was connected to ,you should have very high voltage and should hear it clicking ,If all safety is good ,pressure switch is good ,gas valve is open and no spark from ignition board then board is bad.If you can hear spark from board and getting high voltage then replaced ignitor or try cleaning it out with sand paper most time that healp

Feb 04, 2018 | Heating & Cooling

1 Answer

Dometic RM3801. Propane ignition failure.


The older units has a 3 VDC glow coil the newer units have a 12VDC igniter.

Fromwhat your described above the next paragragh is your ignition system.

The igniter control voltages in the newer SPARK type igniters are (+) = 12VDC, (L)= high voltage lead (Spark plug voltage! I.e ruin your meter type voltage), (-)= Ground L is the lead that passes the HV spark from the control unit to the ignitor plate. The L lead should pass one heck of a hit if is workng correctly.
If not look at the HV lead to see if it is grounding out somewhere.

If the gas safety valve is not sensing gas pressure... you will not have 12VDC to the + terminal of the ignition moudule.

With the gas on and you have 12VDC at the ignition module + terminal then most likely the ignition module is bad.


Kelly


Apr 17, 2010 | Refrigerators

1 Answer

Dometic RM2562 - No Flame


use a set of needle nose pliers & disconnect the igniter wire the module should start clicking if it does not click check the wires to the board clean them good & reconnect if the module still wont start clicking your board is bad if it does click the igniter adjustment off stick a nickle between the igniter & burner the gap should be the size of the nickle 3/16"

May 26, 2009 | Dometic RM2652 Refrigerator

Not finding what you are looking for?
Refrigerators Logo

Related Topics:

429 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dometic Refrigerators Experts

Sheldon Dedek

Level 3 Expert

909 Answers

Paul G
Paul G

Level 2 Expert

156 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22484 Answers

Are you a Dometic Refrigerator Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...