Question about Electrical Supplies

Open Question

What might be the problem,my generator(kipor) is writing run fault on the panel and is failing to start

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
CarlGehrke
  • 169 Answers

SOURCE: Problem with a kipor 12 ta generator

Hi,
I just guessing here but it could mean that the oil pressure is too low.
I'd check the oil level first, then look for the oil pressure switch and temporarily disconnect it.

Regards,
Carl

Posted on Feb 23, 2009

Ad
  • 62 Answers

SOURCE: Kipor 3000ti generator, doesn't start, i checked

Drain carb bowl it could have water in the gas

Posted on Apr 07, 2009

sal_kh_sab
  • 98 Answers

SOURCE: KIPOR KDE 6700TA 5KVA Generator

forget about the display read the manual and find out how many volts are needed to charge the battery....then
get a voltometer and disconnect the terminals from the battery and connect them to the voltometer while the generator is running...
find out what the reading is...if the reading is zero (0)...then post a problem on (no out put)...
if not.....then there has to be a mistake...
if it reads a voltage thats too low..then you AVR card is burnt out (AVR card is located in the other end of the generator (beyond the stator-side cover)...

Posted on Oct 25, 2009

Testimonial: "Khan sb. truly is a professional. "

  • 6468 Answers

SOURCE: kipor generator starts ok but will not provide electricity to apppliances

first check the circuit breakers if there ok the problem is inside like over heated parts

Posted on Sep 08, 2012

SOURCE: Iam looking to download a manual for a Kipor KDE

Try this link:

http://americanrvcompany.com/assets/images/Kipor/KDE5000ETA%20Operation%20Manual.pdf

Posted on Sep 21, 2015

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My kipor generator runs but produces no power. What is likely to be the problem


Is there any circuit breakers or main cut off switch in the off position? If so start the generator and turn on all circuit breakers or cut off switches.

Jan 28, 2018 | Kipor Electrical Supplies

1 Answer

Why unit keeps shutting down after it starts.


Your question is general without specific details. Any one of many things will cause your generator engine to stop running.

Is this question about a Kipor KDE5000TA? If so, your generator is powered by a diesel engine. There are safety shut downs built into the generator to protect the generator head and engine. Do you have any fault codes showing on your control panel display screen? (Trouble codes P-01 through P-05 will be displayed if there's a detected fault)

If you have no fault codes, then you likely have a fuel problem. Do the obvious:
  1. Visually check the fuel level in your tank. DO NOT rely on your fuel gauge. It may be stuck or otherwise not working.
  2. If you have fuel, check your fuel filter. It may be clogged. If your fuel filter is good, you may have water contamination.
  3. Drain your tank and refill with fresh #2 diesel fuel. I use "Diesel 911" with a biocide to prevent water contamination and bacteria growth in my fuel.
  4. Make certain your fuel oil supply and return lines are clear, not leaking, and the fittings are tight.
I know I'm shotgunning, peppering the target. However, I don't have enough information to zero in on a specific area where the problem could be. Good luck!

Apr 26, 2015 | Kipor Generator Diesel Kde5000ta

1 Answer

I have a Wacker portable Gen gs 5.6 It runs good but it also don't put out power ether


I suspect the inverter module has failed. The module failed on my kipor gen and produced the same problem, ie no A/C outpu. Module was about $300 for Kipor. Fitted myself, problem solved.

Dec 06, 2014 | Electrical Supplies

1 Answer

I have generator kipor kde19sta3 when we start then generator after 1 or 2 minutes generator will automatically off and show the fault p 03 so plzzz tell me about p 03 fault thankx


Sounds like an overload on the board. Be sure you're not drawing more amperage out of the plugs on the front of the unit than is listed (typically 12.5 or 20 amps is the limit). If you try and draw more or a surge on the appliance happens during startup, you may end up having to use the 240 volt plug and direct that into a distribution panel to get the 110v unhindered by the plug limitations.

Sep 23, 2013 | Electrical Supplies

1 Answer

Kipor IG3000 generator stepper motor bad?


I just experience the same issue. Mine was a broke wire at step motor. Now to find parts as I hv soldered the wire and works great... I'm sure the others will fail soon enough

Aug 12, 2012 | Kipor Generator IG3000 CARB

2 Answers

Kipor 6700TA displaying charge fault (P5)


Check for loose or rusty battery cables. Unscrew the rear cover and locate the red battery wire. Disconnect it and, using a multi meter, check its resistance: it should have a very low value. Do the same with the other wire.
Start the generator and remove battery wires. If the voltage between them is zero then a fuse is blown.
Next open the front panel (where the display is), there you will find two blue wires with covered fuses, check and replace those fuses if found faulty.
If the problem is still there then it could be the charge regulator. Open the back cover by removing the six nuts. Near the edge you will find a component with silver cover resembling plates. There are three wires leading from it. Check resistance between these wires (one by one) and its body: it should be infinite, if not then replace it. remove the charge regulator and take it to a generator spare shop. The person there will further inspect it and will tell you if you need to replace it or repair it.
Hope this solves your problem.
Thank you for using fixya!

Aug 18, 2009 | Electrical Supplies

Not finding what you are looking for?
Electrical Supplies Logo

Related Topics:

60 people viewed this question

Ask a Question

Usually answered in minutes!

Top Electrical Supplies Experts

Craig Butler
Craig Butler

Level 3 Expert

1730 Answers

Gene Haynes

Level 3 Expert

5353 Answers

Brad Brown

Level 3 Expert

18072 Answers

Are you an Electrical Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...