Question about Hitachi Televison & Video

Open Question

Has anyone ever taken off the splitter on a hitachi c10rj because it sits higher than my 6" dado stack?

Posted by on

Ad

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
RonPark
  • 855 Answers

SOURCE: PM2000 tablet saw won't spin up with 3/4

Check your alignment of the blades, sounds like they are hitting something and will not turn. To check unplug saw and try to turn blades by hand. If they don't turn thats the problem, if they turn check and make sure that the blade is the right type for saw. But if the regular blade works fine you have a binding problem with the dado blades.

Posted on Sep 25, 2009

Ad
  • 257 Answers

SOURCE: I own a Hitachi 10CFR Table Saw. My question is:

After doing some research, I found that hitachi only recommends up to a 1/2 dado for this machine with most of the users agreeing that it probably does not have the stability or power to run a 3/4 inch safely. Meaning you probably can run the 3/4 but at you own risk.

Posted on Mar 03, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

There is no mention in the instructions about the spacers. what are they for.,


They are used to create a "stacked" blade to allow wider dado cuts. Read this link for more info.


Setting Up Your Stacked Dado Set

Nov 27, 2015 | Saws

1 Answer

Model number 137228210


Yes just make sure you have or make a new clearance plate to allow the dado to come thru

Oct 07, 2013 | Craftsman 10" Table Saw

1 Answer

I own a Hitachi 10CFR Table Saw. My question is: Can I load a Dado Stack onto the Arbor of this table saw to create a 3/4 dado cut? I've read everything from "Yes" to "Absolutely Not"...


After doing some research, I found that hitachi only recommends up to a 1/2 dado for this machine with most of the users agreeing that it probably does not have the stability or power to run a 3/4 inch safely. Meaning you probably can run the 3/4 but at you own risk.

Mar 03, 2011 | Hitachi C10FR 10" Job-Site Table Saw 15...

1 Answer

Can you run a dado blade on this saw?


The 15 amp 3 hp motor has plenty of power to handlee dado sets and you can purchase a dado blade insert for the saw on line from multiple resources

Jun 29, 2010 | Hitachi C10FR 10" Job-Site Table Saw 15...

1 Answer

What kind of dado blade can I use on my craftsman 10 inch table saw model no. 137.248100/ with stand


You have a 5/8" diameter arbor. You can use any dado blade that will fit. That said here's a few things to bear in mind.

8" diameter dado stacks are pretty standard for 10" contractor table saws. A dado stack is typically about 13/16" wide at most. It makes sense that the wider your blade is, the more power it takes to cut through the wood.

If you were to use the full width capacity of your Dado stack (13/16") a 10" diameter stack would bog down. A 8" stack has a faster rotation at the cutting edge because of its smaller radius. So, you don't bog down when you're making a wider cut if you use a smaller diameter.

If your machine was really underpowered, you could go down to a 6" stack which would cut your power requirements even more, but limits the depth of cut.

If this post was helpful, please vote. Thanks.

Mar 28, 2010 | Craftsman 10" Table Saw

1 Answer

New dado set understand the shimms and chipper work


The shims are placed between the blades and chippers in a stack. they are used to make very small adjustments to the final dado width... So usually you set up your dado set for a specific width of cut according to your blade chart, then make a test cut... If you need to widen the cut very slightly, add some shims in between the blades as required to get a good fit on whatever material you are joining or putting into the dado etc.

Hope that makes sense!
Please rate this solution on FixYa!

Apr 12, 2009 | Delta 35 7670 8" Stacked Dado Set

1 Answer

Dado blade installation


Yes. normally an eight inch stack dado set is used on a 10 inch saw. You will also have to purchase or fabricate a special throat plate (non-metallic) to accomodate the extra thickness of the dado set.
The number of blades used, and therefore the thickness, varies depending upon the task at hand.
Make sure to use the factory supplied nut and washer to capture and tighten the dado set securely on the arbor.
Be very cautious in the use of dados. Do not raise the set higher than 1/4" or so until you are familiar with the use of a dado set. Try to avoid so-called "wobble" dado sets. They are IMHO more prone to dangerous kickbacks and harder to adjust than a stack dado set with dado shims.

Mar 21, 2009 | Delta TS200LS Shopmaster 10 Inch Portable...

1 Answer

I bought a Dado blade set dd208 and there are no instructions


I'm hesitant to even answer, not knowing your skill level. But understanding that you will probably have a use for an item you purchased, and use it one way or another, here's a primer...
Be careful! Never push your hand directly toward the rotating saw such that if the workpiece kicks back your momentum will carry your hand into the blade. Begin by raising the blade only a little above the table surface and run a pass with clean wood over it to get the feel of the resistance a stack of dado blades gives. Consider making a groove in two or more passes if you need to raise the blade more than 1/4" to cut it in a single pass. Use metal dado shims to adjust the precise width of cut. Tighten the stack in a balanced way, such that the carbide teeth are not in contact with one another. Stay away from wobble dado sets. Etc. Etc. Etc.
You may wish to have a look at this website, whose author has obviously given the subject considerable thought: http://www.newwoodworker.com/usngstkddados.html

Finally, be carefull. If you think a single saw blade can tear flesh, imagine what a 3/4" wide swath will do to your hand. Think about your setups. Use test pieces to get them right. Then pay attention while you run your dados. And try to avoid plunge cuts, especially on anything shorter than a couple of feet in length. When you can, use a miter jig in the slot to hold any work you have to pass cross-grain over the dado.
Be careful, feed smoothly, and hold your workpiece firmly against the fence while it passes over the blade.

Nov 29, 2008 | Saws

Not finding what you are looking for?
Televison & Video Logo

Related Topics:

31 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hitachi Televison & Video Experts

Jaime Hernandez

Level 3 Expert

2337 Answers

The Knight
The Knight

Level 3 Expert

76100 Answers

Steve Allison
Steve Allison

Level 3 Expert

5569 Answers

Are you a Hitachi Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...