Question about GE Dishwashers

1 Answer

I have a GE Potscrubber 900. I have water entering the dishwasher from the opening on the left side, but the water tower does not work. Can you help

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 1,316 Answers

The main pump motor may not be working. If you cant hear it running, it may be jammed up or burnt out. If you can hear a loud humming noise, its possible its only jammed. You will have to remove the pump and see if any foreign matter has stuck in the pump impellor. If the pump is running, check the small outlet holes in the spray arms, they may be blocked.

Posted on Apr 10, 2019

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
  • 114 Answers

SOURCE: ge potscrubber 640 dishwasher

You probably have a restricted water inlet valve. It is not allowing the proper rate of flow for the allotted time, therefore not giving enough water to create the proper velocity to reach the top rack.

Posted on Feb 19, 2008

  • 1 Answer

SOURCE: GE potscrubber 700

upc leaks when dishwasher is emptying

Posted on Sep 03, 2008

rockitman187
  • 2559 Answers

SOURCE: Soap dispenser cover won't close

It sounds like it may be stuck between cycle steps.(this sometimes happens if the washer is open during a cycle)Try and run it through one full wash cycle as it is.Then check to see if the soap door will close.If not,the lack may be broken

Posted on Jan 11, 2009

  • 1 Answer

SOURCE: GE POTSCRUBBER 1200 DISHWASHER

I have a Ge Potscrubber 1200. Fairly new I guess as I bought it with the house that I purchased 1 1/2 years ago. Sometimes it drains and sometimes it does not. Today there was two inches of water! About to remove the bottom panel. Sounds like the drain valve it blocked but not sure. Any thoughts?

Posted on May 06, 2009

localwonder
  • 6784 Answers

SOURCE: Potscrubber 900 Dishwasher won't drain

HI. check the following areas for faults.

1. Air gap / Drain hoses
If there is an air gap (located in the sink, near the faucet), check to see if it is clogged. Unscrew the top cap and see if there is anything blocking inside. Note: If there is no air gap installed, the dishwasher might not drain properly.

If the drain hose is clogged, the dishwasher would not drain. If there is an air gap installed, it is very common that a hose going from the air gap into the garbage disposer is clogged. Remove and clean the hose. Make sure to reattach the hose before starting the dishwasher.

Note: If you recently had a garbage disposer installed, it is common to overlook removing the drain plug.

2. Broken belt
Some dishwasher models use a belt to drive the pump. Replace the belt if found broken.

Note: Sometimes the belt would just come off the pump. Even though it might not be broken, it is recommended that you replace the belt, because it is probably too stretched out.

3. Pump
Some models have two impellers inside the pump - one, wash impeller, takes care of the wash cycles, the other, drain impeller, drains the water out. If the drain impeller is broken (broken blades, shaft), the dishwasher would not drain. Replace any broken pump components.

4. Drain solenoid
Some models (for example most GE dishwashers) use a drain solenoid to drain water out. Sometimes the solenoid gets stuck, preventing the water from draining out. Try to free up the solenoid. If unsuccessful, you might have to replace the pump assembly.

5. Motor
If the motor is stuck, it is sometimes possible to free it up by manually spinning the motor.

Replace the motor if defective.

6. Timer
Replace if defective (note: uncommon problem).

Posted on Aug 27, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

GE Potscrubber 900 just runs and runs, dial just sits there


Hello Debbe,

Does the dishwasher fill with water, or is full and fails to drain?
Can you provide additional detail so that we may accurately troubleshoot? Also include the complete model number. It should be etched or stamped on a plate inside the door, or elsewhere on the washer.

Thank you!

Jan 30, 2018 | GE Dishwashers

1 Answer

Ge potscrubber 800


GE Potscubber 800

Issue: No water.
What works:
- Dishwasher appears to operate normally, just does not call water.
- Water valve works

Suspected:
- Float / float switch

Needed:
How to test float switch

Jun 01, 2013 | GE 24 in. GSD3400G Built-in Dishwasher

1 Answer

How do you remove the sprayer arm from a GE potscrubber 600


Thought I had a problem with the spray arm or pump because water was not flowing enough to spray the upper rack. But it turned out it was a simple part missing: the "check valve" that is in the lower neck of the spray arm assembly. It's a $10 part. Part #WD1X5488 for GE Potscrubber 600.

May 20, 2013 | Dishwashers

1 Answer

Burning smell coming from dishwasher caustic to nose. GE Potscrubber 900. Nothing on element upon inspection. Smell more at beginning of wash cycle or when using the pot scrubber button


Older GE's had problem with drain coils over heating
Remove the bottem front plate and the coil will be on the left side of the moter and activate when the drain cycles, check that

Apr 22, 2010 | GE 24 in. GSD2000Z Built-in Dishwasher

1 Answer

GE Potscrubber disher - water leaks out while filling


I would try removing the cover and make sure the float isn't sticking. On mine the float pushes on a rod that goes through the tub to a micro switch. When you hit it, it probably frees it up for a while. Hope that helps.

Jan 21, 2010 | GE Dishwashers

1 Answer

GE Potscrubber Quiet power1....horrible film left on dishes, especially plastic & tupperware


Hello,
The film is usually due to hard water.

If you have hard water, you need to use gel or liquid detergent only. Try that and use smaller amounts.

Also, you can try flushing out the pipes by using a product called Dishwasher Magic, which is sold at OSH.

Best of luck,
Ned

Sep 18, 2009 | GE Dishwashers

1 Answer

I have a GE Potscrubber dishwasher that only hums, won't run


I have a portable that had the same problem. I called a repairman and he turned a fan blade on the motor. Mine is located on the right side about 12" in. It gets hung up when it is run often enough. If your problem is the same is mine all you have to do is turn the blade and it works like a charm. Hope this helps.

Feb 18, 2009 | GE 24 in. GSD2000Z Built-in Dishwasher

1 Answer

GE potscrubber 700


upc leaks when dishwasher is emptying

May 12, 2008 | GE Dishwashers

Not finding what you are looking for?
Dishwashers Logo

Related Topics:

39 people viewed this question

Ask a Question

Usually answered in minutes!

Top GE Dishwashers Experts

Mike

Level 3 Expert

4357 Answers

Archie Ferrarini
Archie Ferrarini

Level 3 Expert

869 Answers

Vitally Alcher

Level 3 Expert

1645 Answers

Are you a GE Dishwasher Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...