Question about Husqvarna Sewing Machines

1 Answer

I have a Husqvarna 550. The bottom thread suddenly started clumping and the machine now makes a clunking noise. This happened suddenly. I have rethreaded 3x, nothing visible in the bobbin case.

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    MVP:

    An expert that gotĀ 5 achievements.

    New Friend:

    An expert that has 1 follower.

    Corporal:

    An expert that hasĀ over 10 points.

  • Contributor
  • 16 Answers

Make sure you are using the correct bobbin, and that it was threaded properly. Check needle and plate to make sure there are no nicks. Clean all fuzz from the bobbin area. Always thread needle with needle down.

Posted on Apr 17, 2019

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
  • 27 Answers

SOURCE: Brother Sewing Machine model:CS8150 bobbin thread problems

The top of the machine is not threaded correctly. First raise the presserfot then rethread the machine. Bottom looping is usually caused by a lack of top tension. There could allso be a bur on the hook.

Posted on Feb 23, 2008

SewExpress
  • 41 Answers

SOURCE: Picking up the bobbin thread

A few suggestions:

  1. Rethread top of machine from scratch with the presser foot raised, i.e. remove thread completely from all thread guides & paths and start from scratch, making sure thread is securely seated between tension disks. Once the needle is re-threaded, lower the presser foot and give the tail end of the thread a tug to make sure there's tension on it.
  2. Make sure the bobbin is turning the correct direction for your machine - and that the thread tail is under the tension plate or bobbin tension guide (depending on machine).
  3. Blow out any fuzz.
  4. Insert a new needle, making sure needle is pushed all the way up.
  5. Oil machine (in locations recommended in your owner's manual).
If the basic cleaning and re-threading (above) don't help, your machine(s) may be out of time or have another mechanical issue that will require a repair technician. We recommend a tech trained on your specific brands - they'll be better trained and able to get any repair parts that may be needed.

Hope this helps narrow down your stitching problems.

Happy sewing,
Kim & Linnette

Posted on Jun 27, 2008

lavon82931
  • 17 Answers

SOURCE: needle won't grab bobbin thread

Check the position of the needle. Some machines have to have the needle in a certain way or they won't pick up the thread from the bobbin. Make sure the screw on the bobbin is tight but not to tight you may have to adjust it a few times to get it where it needs to be. Also make sure the bobbin is wound tight

Posted on Oct 14, 2008

  • 323 Answers

SOURCE: noise from bobbin case on new Janome 4020

Check the bobbin to be sure it is inserted correctly. When you pull on the bobbin thread the bobbin should turn to the left(orcounterclockwise). If it doesn't, the thread will come out of the bobbin tension and give you loose stitches on top of the fabric. It will also make a noise because the bobbin is bouncing up and down.you will need to readjust your tension again.
sewman7

Posted on Dec 24, 2008

miket756
  • 2702 Answers

SOURCE: NEEDLE WON'T PICK UP BOBBIN THREAD

im not!
it needs a good service the timeing has sliped out a little, nothing more that that,,,see its not a lost cause just yet

Posted on Oct 24, 2009

Testimonial: "Thanks! I was hoping to avoid paying for a fix, but it looks like I have to **** it up. So much for being thrifty and restyling my clothes."

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Machine making load noise after stop sewing, what is that?


We all know that proper threading makes for happy sewing machines and happy stitchers. And while we emphasize threading with your presser foot up- there are a few other things to keep in mind while threading your machine to make sure your sewing time is happy time!
Have you ever been sewing along on a project, decided to change threads, and all of a sudden you hear a THUNK CLUNK THUNK when you start sewing again?
If not, good for you. But I know that this has happened to a lot of our customers for sure!
Often, this sound comes from not getting your thread in the take-up lever while threading.
If you have a new needle that is the appropriate size/type and your machine is clean, but you start to hear a clunking sound after rethreading, this is the first thing to check. And it's such an easy fix. In fact, I think some people are so surprised when we tell them to simply rethread, because the sound is so terrible they think something is seriously wrong with their machine.
Now, there could be something really wrong with your machine, but the biggest clue that it's a missed take-up lever is that the problem starts suddenly, most of the time after rethreading. (machine was sewing just fine before that).
How do you make sure to thread your take-up lever?
On some machines, it's very easy to see the take up lever, and on others it's hidden behind the machine casing. Here's what you should do to try and ensure success.
-Raise your presser foot!(Full rant here)
-Put your needle in the highest position (use the needle up down button or line up the notch on your handwheel with the casing of your machine- more info here)
-Clear the thread path. Make sure there's no thread wrapped around a spool cap or trapped under your spool.
-Feel it! If your presser foot is up and your needle in the highest position, hold the thread near the spool with your right hand and thread with your left, you'll be able to feel the thread slide into the take-up lever.
-STOP immediately if you hear a THUNKing sound and re-thread. What's happening is that your top thread is not regulated, and it can ball up undereath the feed dogs and cause issues.
-Clean out your bobbin area and re-thread if you think you missed your take up lever.

Aug 25, 2017 | Sewing Machines

1 Answer

How to remove top cover of lily 550


Make sure the presser foot is in the up position. This will open up the tension disks. It takes a lot of patience to remove imbedded thread. Use tweezers to grab the thread. Rock the handwheel backwards and forwards to help release the thread. If all that fails, have it cleaned by an authorized Husqvarna Viking dealer. You can find your nearest dealer at the viking website - http://www.huqvarnaviking.com/us

Jul 12, 2014 | Husqvarna Lily 540 and 550

1 Answer

Thread around wheel


If it were my machine I would pull the back cover for better access to the rotating shaft and remove the remaining thread. If the thread works its way into the shaft bearings you will have a real mess.

Feb 24, 2014 | Husqvarna Lily 540 and 550

1 Answer

Bernina troubleshooting


Bernina 880 - the dual feed will suddenly start making a loud "clunking" noise and making very tiny stitches. Then just as suddenly it will begin to work again - but the stitching is clumped, uneven with loops on the back. Then it will start working fine again until the next time... I called the dealer and talked directly with the repair person. He had never heard of that before. Anyone have any answers? Did I get a lemon?

Jan 04, 2014 | Sewing Machines

1 Answer

Husqvarna Viking - Thread gets caught up on the underside of material when trying to sew.


There are two things that come to mind that may be causing the problem.
1) Change the needle, for it could be bent even thought it may not look it. (This is the most likely cause).
2) Have a look just inside and check if any screws have come loose. This has happened to me. (Even the repair man did not find it.

Nov 29, 2013 | Sewing Machines

1 Answer

I am totally new to machine sewing and I have a Husqvarna Model 400, its been working perfect then suddenly when sewing the thread from underneath (the spool side) is just coming out in huge clumps, the...


When you say "the spool side" I assume you mean the bobbin. There are a couple of reasons why this could be happening. First re-thread your upper thread with the presser foot up and check to see if the top thread is firmly in the tension disc. Usually when you have looping of thread on the underside of your fabric, it is the upper thread that is out of whack. Just the opposite of what you would think! When you're sure the top thread is right check your bobbin to make sure that's wound tight and not "mushy." When you start by wrapping the thread around the bobbin by hand and then put it on the winder to fill it, it is not tight enough so the whole bobbin winds too loose. This can cause clumps underneath. The last thing to check is that the bobbin thread is caught in the tension slot in the bobbin case and that there is no stray threads in the bobbin case opening to cause trouble. Hope this helps. Good luck. You have a great machine!

Sep 10, 2010 | Husqvarna Sewing Machines

1 Answer

Hi, I have a huskylock 905 NOT computerized and it's making a "clunking" noise while sewing and then the "D" thread breaks. I've re-threaded many times, changed thread, changed needles, adjusted tention...


Sounds like the D needle is hitting something in the loopers and an adjustment needs to be made. The adjustments are ever so slightly. It could be that the needle bar is twisted causing the D needle to hit. It could be the looper is not within the specs for proper operation, etc. Suggest you take it to an authorized husqvarna viking dealer for service. You can locate a dealer near you by visiting the husqvarna viking website and clicking on the Dealer link on the left-hand side of the page - http://www.husqvarnaviking.com
Good luck.

Nov 18, 2009 | Husqvarna Huskylock Computerized 905

1 Answer

Husqvarna Viking Designer 1 keeps breaking needles


The threading may be out of the channels. Rethread. Put in a fresh needle. Make sure you are using an embroidery needle and a new one for each new project. You can't use YLI bobbin thread. It stinks. If all this doesn't help, take it in to be checked These work great when there is not thread stuck in the bobbin case and it is threaded properly. If all is well, it will go like gangbusters.

May 21, 2009 | Husqvarna Designer I

1 Answer

Husqvarna bottom thread showing through the top


On the far left of the machine is the tension wheel for the bobbin. Sounds like it is way too loose. Should automatically set if you have entered the right type of fabric.

May 08, 2009 | Husqvarna Viking 1

1 Answer

Thread keeps wrapping around bobbin


frustrating huh?  it happens!  even to us that have been sewing for 50+ years, but the solution is very simple.  Top thread tension is the culprit.  pull the spool all the way off and rethread the top, follow the threading path precisely and make sure the thread goes down into the tension discs.
one more thing - when that happens often times the piece has to be removed from the machine by cutting those annoying loops on the bottom.  if this is the case, make sure you have removed all the thread clippings from in and around the bobbin case.  sometimes one little piece of thread will make you want to use swear words.
good luck and happy stitching.

Jan 17, 2009 | Husqvarna Viking 1

Not finding what you are looking for?
Sewing Machines Logo

Related Topics:

28 people viewed this question

Ask a Question

Usually answered in minutes!

Top Husqvarna Sewing Machines Experts

radcal

Level 2 Expert

196 Answers

Douglas Plant
Douglas Plant

Level 2 Expert

222 Answers

Tally Girl
Tally Girl

Level 3 Expert

1134 Answers

Are you a Husqvarna Sewing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...