Question about Kenmore Washing Machines

1 Answer

I have a used Kenmore washer ser # M2347937 80 series where do you put the fabric softener in at?

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Genius:

    An expert who has answered 1,000 questions.

  • Master
  • 1,041 Answers

If supported, the fabric softener goes in the the center spindle.
see manual:
https://c.searspartsdirect.com/mmh/lis_pdf/OWNM/97110273.pdf

Posted on Apr 16, 2019

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
  • 1 Answer

SOURCE: Kenmore Front Loading machine, does not drain the fabric softener

We had the exact same situation with the fabric softener not draining and here is how we fixed it. Turn the water off first, then remove the water lines that bring water into your washer. (They are near the top.) There is a screen in the end of the line, do not remove it, but take an old toothbrush and brush the gunk out and clean it as best you can. Do both the hot & cold sides. The screens keep any debris out of the washer, so after a while it collects and slows down the water intake time (has your washer been slow to fill also?) Screw back the lines, making sure to put the hot and cold back as they were originally, then test that they do not leak. Put your washer back in place and viola - problem solved! I hope this works for you, and good luck!

Posted on Oct 28, 2006

57 varieties
  • 1653 Answers

SOURCE: My bosch nexxt washer will not drain the fabric

Take out the drawer and clean the compartment and pipe at the end of the drawer with hot soapy water - washing up liquid works well. Clean all around it. To show this is working OK, put it in the sink and fill up the compartment with water until it is overflowing then stop. The water should drain out of the compartment on its own.

Next, where the drawer fits in the machine clean the water exit above the drawer with a washing up brush. This can appear brown or white depending on your water type. If this is OK try running the machine. If there is still a problem, remove the drawer again and turn off the power at the mains. Use something like a paper clip to poke all the holes in the water dispenser area above the drawer. There are lots of them so some patience might be required. If you live in a hard water area it could be blocked with limescale in which case an application of a descaling mousse or spraty will assist. Once complete, make sure you rinse the drawer area, drawer and put the drawer back in and run the machine on a short cold fill wash cycle. Put some fab con in the drawer to test that the machine drains it correctly. If all is well then there will be no fab con left. If it is still there then you will need to get into the water dispensing area to see what is wrong. Occasionally the mechanism can get jammed, lose a spring or just get broken, in which case it will need replacing.

Posted on Oct 23, 2009

blueextc3221
  • 15935 Answers

SOURCE: Kenmore Elite HE3T front loading washer - got a

The "SUDS" error can be caused by too much detergent, improper detergent, drain pump/drain line problem, or pressure switch malfunction.

1. If you are not using HE detergent, you need to be. These washers are designed to use HE detergent which is formulated for wash tubs that use 5 to 7 gallons of water. If you use regular detergent, you are, in affect, placing a higher concentration of detergent in the washer that is normally formulated for wash tubs that have a 35 gallon capacity. The manufacturer should have a disclaimer in the owner's manual explaining this. In most cases this will also void your warranty. NOTE: Prolonged use of the wrong detergent can damage the drain pump components and or wash tub seals.

If you are using the correct detergent, double check the label to make sure it is not double (2X) or triple (3X) concentrated. You could still be placing too much soap in your wash.

To get rid of excessive detergent, place the washer on a RINSE & SPIN cycle, then run it through a normal wash cycle with NO detergent added. You may have to repeat these steps depending on the amount of detergent used.

2. If you do not have a detergent issue, double check the drain pump and drain lines to ensure they are not obstructed in any way. Click on the following link for step-by-step instructions:

http://www.fixya.com/support/r385844-checking_drain_pump_kenmore_elite_front

Obstructions in the drain pump and/or drain lines can attribute to air getting trapped in the drain pump and cause the error code. Double check all electrical connections to the drain pump and Central Control Unit (CCU). You will need to remove the top panel of the washer to access the CCU. This is accomplished by removing the three screws in the back of the washer that hold the top panel in place. With the screws removed, slide the panel back, then off. The CCU is located directly behind the wash tub in the center of the washer. The Drain Pump connector will be the 6th connector (facing from the front L to R) in the center of the CCU.

3. Check the Pressure Switch to ensure it is good. The Pressure Switch is located to the right of the CCU as you are looking from the front. It is a small cylindrical shaped device with a connector plug and an air hose attached. The switch can be checked at several water levels by removing the plug and taking resistance readings at the connector pins. Readings are as follows:

(Pins are numbered R to L facing the from the REAR)

Pins 1 to 2 (SUDS Detect) – 0 ohms
Pins 3 to 4 (Overflow) – 0 ohms
Pins 4 to 5 (L1) – 0 ohms
Pins 4 to 6 (Empty) – 0 ohms
(tip by JSRock)

Thanks for using FixYa - a 4THUMBS rating is appreciated for answering your FREE question.

Posted on Apr 14, 2010

  • 1 Answer

SOURCE: kenmore 3.5 super capacity front load washer won't dispense fabric softener

Kenmore 110 front load washer wil not dispense fabric softner. Code 21. Have already checked pump and filter obstructions

Posted on Apr 18, 2010

  • 70 Answers

SOURCE: The fabric softener is nto being used in the

The old top loaders would say "use diluted fabric softner" on the dispenser. Yours may not say anything, but this is an easy fix.

Posted on Jun 23, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My Kenmore 400 series washer does not seem to be releasing the fabric softener properly. It ends up all around the top if the barrel and spotted on my clothes as well. Anything I can do other than g


the dispencer can at times become plugged with old soap and farbic softener and should be cleaned every so often. if it cannot dispinse it will shoot out the dispenser all over when it goes into spin. the lines can even get plugged up and not allow fabric softerner to flow , u may want to remove fabric hoses and clean them

Nov 08, 2014 | Kenmore Washing Machines

1 Answer

Fabric softener compartment


You will need to clear the line from the fabric dispenser to the tub.

Oct 15, 2012 | Kenmore HE2 Plus Front Load Washer

1 Answer

Kenmore 600 series fabric softener dispenser clogged


How do I make the waher Kenmore drop the fabric softener

Aug 25, 2012 | Kenmore 600 3.5 cu. ft. Top Load 110-2962...

1 Answer

After filling compartments correctly and closing the tray, I see the fabric softener emptying into the washer. Tray does not leak softener when removed and filled.


Hi,
You are putting too much in there... the tray empties on a siphon priciple... if you fill it too high it will just siphon out...

Use less fabric softener...

heatman101

Dec 13, 2010 | Kenmore Elite HE5t Washer

1 Answer

Getting E:13 error on Nexxt 300 series washer


Try putting the washer on COLD and run "TWO" cycles. It must be on COLD. There is a chance there is too much soap or fabric softener in the washer. It may also help to clean the fabric softener tray where you add the softener.

Nov 22, 2009 | Bosch Nexxt 300 Series WFMC2201UC

1 Answer

Dual action kenmore 70 series washer need to remove agitator


First, see the Sears parts site for your washer:
http://www.searspartsdirect.com/partsdirect/index.action

Enter your model number (###.######) and you'll see a list of major sub-components with diagrams and parts.


It sounds as if your "Agitator Dogs" are damaged or broken. These are plastic pieces that allow the top agitator to turn only one way.

Please see the following for how to access and replace them if necessary.


http://www.american-appliance.com/catalog/newsdesk_info.php?newsPath=16&newsdesk_id=136&osCsid=39649e541343127154c647348d1156d9

Basically,

1. Remove the fabric softener dispenser.

2. Using a short flat blade screwdriver, remove the cap.

3. You may see a 1/2" square plastic nut.

I've used a 1/2" extension for a socket set to remove the nut.

4. Pull the top agitator off and turn it over carefully.

You should see the agitator dogs (per the illustrations).

Replace them if necessary and re-mount the agitator, tighten the bolt carefully, put the cap and fabric softener dispenser back on and the top part of the agitator should only turn one way.


Nov 06, 2009 | Kenmore Washing Machines

1 Answer

How do i clean the fabric softener dispenser in my kenmore 80 series washer? Does it come apart to clean the inside? It is full of gunk and the fabric softener won't come out.


If it's located at the top of the agitator. It pulls off. Pull straight up. After you have removed it. Run hot water through it. Take a old toothbrush and brush down inside it. You can use Mean Green to help cut the goo. Now rinse and shake over and over. Pop it back on.
Please rate solution

Aug 27, 2009 | Kenmore 24902 Top Load Washer

1 Answer

Put fabric softener in the soap dispenser


Just run the load. You can always re-wash.



Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question

Mar 30, 2009 | Kenmore Washing Machines

3 Answers

Kenmore Front Loading machine, does not drain the fabric softener


We had the exact same situation with the fabric softener not draining and here is how we fixed it. Turn the water off first, then remove the water lines that bring water into your washer. (They are near the top.) There is a screen in the end of the line, do not remove it, but take an old toothbrush and brush the gunk out and clean it as best you can. Do both the hot & cold sides. The screens keep any debris out of the washer, so after a while it collects and slows down the water intake time (has your washer been slow to fill also?) Screw back the lines, making sure to put the hot and cold back as they were originally, then test that they do not leak. Put your washer back in place and viola - problem solved! I hope this works for you, and good luck!

Sep 03, 2006 | Kenmore 44102 Front Load Washer

Not finding what you are looking for?
Washing Machines Logo

Related Topics:

53 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kenmore Washing Machines Experts

fordexpert

Level 3 Expert

5692 Answers

Kristen Denison
Kristen Denison

Level 1 Expert

13 Answers

Jim Chinnery
Jim Chinnery

Level 1 Expert

10 Answers

Are you a Kenmore Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...