Question about Whirlpool Washing Machines

1 Answer

What does error code f50, mean for a whirlpool cardio washer? It will add water, but when it calls for drain or spin, maybe just spin it classes the code.

If it is rps that needs replaced how can I check, or if it is the board that needs replaced how can I check ?

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Genius:

    An expert who has answered 1,000 questions.

  • Master
  • 1,041 Answers

Https://www.searspartsdirect.com/washer-repair/error-codes/whirlpool-cabrio-top-load-washer-error-codes.html
Motor Stalled The motor RPS (Rotor Position Sensor) detects no rotation of the drive motor. Unplug the washer. Check to see if the basket spins freely. If not, then examine the drive system and eliminate the cause of friction. If the basket spins freely, check the wire harness connections between the main electronic control board and the motor. If the wire harness connections are okay, check the drive motor. If the motor is defective, replace it.

Posted on May 27, 2019

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
  • 240 Answers

SOURCE: F50 error code and Whirlpool Cabrio

this code would indicate rps sensor at motor. whirlpools are very bad with electronics and control boards. New rps sensor requires new harness as well.

Posted on Mar 14, 2009

  • 111 Answers

SOURCE: Cabrio won't spin

F then 50 flashes when the motor rotor position sensor (RPS) senses no rotation. ➔ Does basket turn freely? If not, make sure bottom shipping pack has been removed. Determine cause of friction
its SD not 5D
Sd is displayed when the machine/motor control, by analyzing drag on the basket, detects a suds-lock condition, and is steady on while the control then runs a mini-clean out cycle. If the clean out cycle is unable to correct the over-sudsing problem, the cycle ends and Sd flashes in the display. This may signify: ➔ Load is bunched or twisted around agitator. ➔ Excessive detergent usage. ➔ Basket cannot engage during drain step. ➔ Mechanical friction on drive mechanism, not allowing basket to engage.

Posted on Jul 13, 2009

  • 1 Answer

SOURCE: Whirlpool Duet Washer Trouble Code F25

TOP SOLUTION
The thing is most people have never used a washing machine before, its alright. If you like calling Whirlpool they will track your phone number and in the future they know you like to buy repair parts. The front load washer for the home is a new concept especially with steam etc. use patience and common sense. no washer can really wash 15 pairs of jeans and spin 150 miles an hour several times a week in this you must see the problem . so use common sense when filling the drum and do not use the highest spin cycle unless you are washing very light items. to fix f25 (happened to me after 1 month and I purchased a floor model) the fix is easy and does not involve a circuit board even though there are many buttons that light up. A repair man would love to order you any part you want plus markup, suggest the balancing mechanism and you will have made a new friend. give it up if you know you had to push on the door , maybe take a running jump to get it to close.you cannot wash a months worth of clothes all at once 1. unplug unit 2. remove 2 to 3 screws from bottom of front panel 3. next gently check connections, some may need tightening but again be patient and use appropriate pliers but mainly use gentle pressure 4.many will discover how simple it would be to work on the washer especially if you opted for the pedestals (worth every penny) 5. notice the drain trap cleaning access white and circular and turns, with a towel underneath open and clean trap at least once a year ...before replacing panel do a test rinse and spin. you will notice that once the f25 code appears there is no resistance to turning the drum this only helps to protect certain parts, once the appropriate wire is no longer loose this resistance is no longer...test but still be patient wait while the machine goes through the motions. don't start pushing every button. drum starts turning properly then replace panel. there is taped to the panel a manual with a breakdown of all the error codes. remember this is a very expensive piece of merchandise and will do for you what dry cleaners would have done for you (yes it has a wash by hand button and the machine will not spin to remove water in clothes on this selection, it will only turn to agitate , just remove clothes, hand wring out into the drum then hang or place in a plastic bag and refrigerate for a day or so until you can hang items)** I was able to my surprise wash a 110 year old linen tablecloth using this feature (soak items that require special stain removers and rinse before putting them in this machine. this machine is fantastic BUT be patient, and do not overload and do not spin everything on the highest setting. In being patient I was able to wash a king size comforter and the slip covers of a 90" sofa (not together) the machine can do this, not every day, but choose the correct setting such as bulky or heavy duty and select appropriate settings. I know for the money one should not have to take off the front panel but remember the machine weighs 200 pounds and coming from whatever factory one can only imagine what happens to machines that are abused in transportation. The key is to be patient and use common sense, if waiting on the machine to finish or the door to unlock ( the reason for the multiple locking steps is to allow those who have decided to get into the machine the opportunity to get out) then I will use the dreaded word of multitask otherwise enjoy the experience. I know I love mine!!!

Posted on Jul 20, 2009

  • 1 Answer

SOURCE: F50 error code and Whirlpool Cabrio

JUST SPOKE WITH WHIRLPOOL ABOUT THE F-50 CODE. THEY SAID THAT THEY ARE AWARE OF THE PROBLEM AND THEY ARE PAYING TO FIX IT. ALSO THE CONTROLL BOARD AND THE RPS SENSOR MUST BE REPLACED TO FIX THE PROBLEM. THE OWNER MUST CALL WHIRLPOOL, NOT THE TECH, TO GET THEM TO PAY FOR IT. HOPE THIS HELPS.

Posted on Mar 29, 2010

ladiestch
  • 19 Answers

SOURCE: Silverdragon posted on here about the Whirlpool

Tip mch back and locate the lg allen bolt in the center of the magnet and remove counterclokwise. The motor is actually a large magnet that revolve around a stator, a series of windings. Pull hard and place magnet away from any metal. Once off, remove the bolts holding the stator to the base and on the reverse side is the rps sensor. It looks like a wedge and is clipped onto the stator.

Posted on May 03, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I need the service manual for a Whirlpool Cabrio WTW6600SW2 to find out what the code F50 mean and how to replace RPS sensor.


The F50 error code indicates that the RPS (rotor position sensor) detects no motor rotation. Check to see if the basket spins freely. If not, you could have an item caught between the outer tub and the inner spin basket. A toy or other item underneath the washer could also prevent the basket from spinning and would result in this F50 code.

If the basket spins freely, you could have a wiring failure that would prevent the motor from spinning.

Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question#$%^

Jun 29, 2010 | Whirlpool Cabrio WTW6600SBT Top Load...

1 Answer

Whirlpool washer wtw6400 giving F50 error message. i need it fix quick.


The F50 error code indicates that the RPS (rotor position sensor) detects no motor rotation. Check to see if the basket spins freely. If not, you could have an item caught between the outer tub and the inner spin basket. A toy or other item underneath the washer could also prevent the basket from spinning and would result in this F50 code.

If the basket spins freely, you could have a wiring failure that would prevent the motor from spinning.

Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question@#$%

Jun 21, 2010 | Whirlpool WTW6400SW Top Load Washer

1 Answer

ERROR MESSAGE F50


The F50 error code indicates that the RPS (rotor position sensor) detects no motor rotation. Check to see if the basket spins freely. If not, you could have an item caught between the outer tub and the inner spin basket. A toy or other item underneath the washer could also prevent the basket from spinning and would result in this F50 code.

If the basket spins freely, you could have a wiring failure that would prevent the motor from spinning.

Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question%^&*(

Jun 14, 2010 | Whirlpool Cabrio WTW6600SBT Top Load...

1 Answer

My Whirlpool Cabrio WTW6400SW2 has a F50 error. I


The F50 error code indicates that the RPS (rotor position sensor) detects no motor rotation. Check to see if the basket spins freely. If not, you could have an item caught between the outer tub and the inner spin basket. A toy or other item underneath the washer could also prevent the basket from spinning and would result in this F50 code.

If the basket spins freely, you could have a wiring failure that would prevent the motor from spinning.

Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question$%^&

May 10, 2010 | Whirlpool Cabrio WTW6600SBT Top Load...

1 Answer

My Whirlpool Cabrio 6600sw2 has lots of problems, it stops and flashes F50 over and over again, it also flashes many of the other codes, it doesn't fill with enough water and it is not washing the clothes...


The F50 error code indicates that the RPS (rotor position sensor) detects no motor rotation. Check to see if the basket spins freely. If not, you could have an item caught between the outer tub and the inner spin basket. A toy or other item underneath the washer could also prevent the basket from spinning and would result in this F50 code.

If the basket spins freely, you could have a wiring failure that would prevent the motor from spinning.

Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question****

Jan 03, 2010 | Whirlpool Cabrio WTW6600SBT Top Load...

2 Answers

Whirlpool Cabrio F50 Error


Most likely the RPS sensor or the control board. Originally they had trouble with the RPS sensors.

Aug 25, 2009 | Whirlpool Cabrio WTW6600SBT Top Load...

1 Answer

F50 Error Code on Whirlpool Cabrio Washer


The F50 error code indicates that the RPS (rotor position sensor) detects no motor rotation. Check to see if the basket spins freely. If not, you could have an item caught between the outer tub and the inner spin basket. A toy or other item underneath the washer could also prevent the basket from spinning and would result in this F50 code.

If the basket spins freely, you could have a wiring failure that would prevent the motor from spinning.

Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question&&&&

Aug 23, 2009 | Whirlpool Cabrio WTW6600SBT Top Load...

1 Answer

F50 error code and Whirlpool Cabrio


this code would indicate rps sensor at motor. whirlpools are very bad with electronics and control boards. New rps sensor requires new harness as well.

Feb 21, 2009 | Whirlpool Cabrio WTW6600SBT Top Load...

3 Answers

Code f50


It has a faulty control board. sorry but this a bad part from the factory. There is class action lawsuit against whirlpool about it. Call and complain and then maybe they will pay to fix it.

Nov 18, 2008 | Whirlpool Cabrio WTW6600SBT Top Load...

6 Answers

F50 error code and Whirlpool Cabrio


JUST SPOKE WITH WHIRLPOOL ABOUT THE F-50 CODE. THEY SAID THAT THEY ARE AWARE OF THE PROBLEM AND THEY ARE PAYING TO FIX IT. ALSO THE CONTROLL BOARD AND THE RPS SENSOR MUST BE REPLACED TO FIX THE PROBLEM. THE OWNER MUST CALL WHIRLPOOL, NOT THE TECH, TO GET THEM TO PAY FOR IT. HOPE THIS HELPS.

Feb 08, 2008 | Whirlpool Cabrio WTW6600SBT Top Load...

Not finding what you are looking for?
Washing Machines Logo

Related Topics:

34 people viewed this question

Ask a Question

Usually answered in minutes!

Top Whirlpool Washing Machines Experts

Marvin
Marvin

Level 3 Expert

85161 Answers

Gerry Harvey
Gerry Harvey

Level 3 Expert

1481 Answers

jimorris77

Level 3 Expert

411 Answers

Are you a Whirlpool Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...