Question about Gucci Watches

1 Answer

I need fixing pin for stainless steel Gucci 105watch bracelet

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Gucci Master
  • 63,744 Answers

GO SEE A JEWELRY STORE . BEST BET TO FIND WATCH PINS

Posted on May 30, 2019

Ad

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
  • 55 Answers

SOURCE: I have a Navy Seals

parsecent.com...they have all the parts to fix it with and they also have to band-to-case piece that you've lost

Posted on Nov 09, 2009

matt2414
  • 247 Answers

SOURCE: Alfred Dunhill stainless steel watch bracelets

This might help:
http://www.info.com/stainless%20steel%20bracelets?cb=27&cmp=4089&gclid=CLmY5aWk1aACFWV75QodumH8uQ

Posted on Mar 26, 2010

  • 299 Answers

SOURCE: I need a bracelet pin and the steel insert for a Montbrillant nav

Any jeweler that sell watches should have the springbars and tubes you need and be able to put them on for you for less than $10. If there's a Breitling dealer nearby that's your best bet but really any watch shop or watchmaker can help you.

Posted on Apr 24, 2010

  • 11800 Answers

SOURCE: Looking for Rado Diastar Anatom watch bracelet

The only source for separate original links is a repair shop that has a defective watch kept for parts. You could order an entire bracelet but that would be very expensive.
The cheapest solution is to get a copy like
http://www.flyingshops.com/rado-anatom-mens-watch-r10365151-4796-p.html
and use its bracelet.

Posted on Jul 13, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Caravelle by bulova 43b17how to adjust Stainless steel bracelet


To remove some links: If you don't have special tool, at least you have to have something really hard and thin (like the pin you use to post notes on the cork board). Put that pin in to the tiny hole between links where the bracelet pin is and then press/push it forward (follow arrow direction as shown on the inside of the bracelet links.) When the bracelet pin comes out at one end, pull it out of that end totally.
After removing one links, connect the two links next to each other by placing the bracelet pin back into the hole and push it to the other end.
To add some links: You have to have spare links and do the same way with the pin to attach more links.

Feb 17, 2011 | Watches

1 Answer

Tissot Seastar 1000 Does anyone know of a source


Tissot is Swatch. They do not sell parts! You need to contact the company OR where you purchased the watch.

http://www.tissot.ch/?mod=stores&action=search&search=&regions=2&countries=195&countryregions=&option=cs

Jan 14, 2010 | Tissot Diver Seastar 1000 Auto Steel Large...

1 Answer

Seiko kinetic stainless steel bracelet has snapped pin (both snapped ends still visible and flush in last flared bracelet link between watch body and start of bracelet.) How do I remove snapped pin ends...


There are several easy to follow tutorials on u-tube. It's easier for you to look at these than for me to describe how it is done. Just search "adjusting steel watch straps"

Sep 23, 2017 | Omega Seamaster 2541.80 Wrist Watch

1 Answer

Adjust watch band for Seiko 7T94 Stanless Steel Band


You may or may not have arrows inside bracelet. Arrows are pointing the way the pins must come out.
First you have to find out what sort of pins or even screws are used to keep links together.
Examine both bracelet sides and find the side where pin ends have a groove.
Start with a tiny screwdriver and unscrew one of the screws. If it turns, but doesn't come out, that means you have a pins instead.
For removing pins the best would be pin removing tool (approx.5GBP on ebay), but it's possible to do the job without it.
Take a hardened steel needle and blunt the sharp end to the approx. size of pin end diameter using any sharpening stone or sandpaper. Get an old towel and fold it to make a soft base for work (like small cusion). As you don't have a special bracelet holder you will need a pair of helping hands to hold the bracelet steady upright. You will need small hammer and pair of flat nose pliers as well.
NOTE: The pins MUST be driven split end out first, not vice versa. Make sure that the grooved pin ends are facing towel, not the needle and hammer!!!
Now place the watch on the folded towel, take that needle and smallest hammer you have and start driving the pin out using light blows. Do Not hit hard, as you will brake the needle, scratch your watch or even injure yourself. Watchmakers are using 45 gram hammer, so, calculate your strength of blows.
After a few blows check if the split end is coming out and when you see that the end is long enough to grab it with pliers, pull the pin out with pliers. When pulling, do NOT turn pliers, as pins tend to brake when twisted. Use firm grip and your strength to pull the pin without twisting.
After shortening the bracelet or adding extra link(s) make sure that the pins go back EXACTLY the same way as they came out- the blunt end first in the hole and the split (grooved) end last. Before doing that check remaining pins in bracelet to make sure that you put them back from the right side of bracelet.
It is recommended to use plastic hammer to drive pins back in or you will scratch or damage bracelet. If plastic hammer is not available use an old toothbrush handle (or some plastic item) as an absorber. Simply put pin into the hole as deep as you can with your fingers, put the toothbrush handle on split pin end and hit handle, not the pin.
Make sure that pin ends are flush with bracelet. If needed- hit few more times.
Job done!
If you do not want to do it yourself, any jeweler will do it in a matter of few minutes.
Don't forget to rate, please.

Apr 04, 2009 | Seiko Watches

1 Answer

Stainless steel band adjustment


You may or may not have arrows inside bracelet. Arrows are pointing the way the pins must come out.
First you have to find out what sort of pins or even screws are used to keep links together.
Examine both bracelet sides and find the side where pin ends have a groove.
Start with a tiny screwdriver and unscrew one of the screws. If it turns, but doesn't come out, that means you have a pins instead.
For removing pins the best would be pin removing tool (approx.5GBP on ebay), but it's possible to do the job without it.
Take a hardened steel needle and blunt the sharp end to the approx. size of pin end diameter using any sharpening stone or sandpaper. Get an old towel and fold it to make a soft base for work (like small cusion). As you don't have a special bracelet holder you will need a pair of helping hands to hold the bracelet steady upright. You will need small hammer and pair of flat nose pliers as well.
NOTE: The pins MUST be driven split end out first, not vice versa. Make sure that the grooved pin ends are facing towel, not the needle and hammer!!!
Now place the watch on the folded towel, take that needle and smallest hammer you have and start driving the pin out using light blows. Do Not hit hard, as you will brake the needle, scratch your watch or even injure yourself. Watchmakers are using 45 gram hammer, so, calculate your strength of blows.
After a few blows check if the split end is coming out and when you see that the end is long enough to grab it with pliers, pull the pin out with pliers. When pulling, do NOT turn pliers, as pins tend to brake when twisted. Use firm grip and your strength to pull the pin without twisting.
After shortening the bracelet or adding extra link(s) make sure that the pins go back EXACTLY the same way as they came out- the blunt end first in the hole and the split (grooved) end last. Before doing that check remaining pins in bracelet to make sure that you put them back from the right side of bracelet.
It is recommended to use plastic hammer to drive pins back in or you will scratch or damage bracelet. If plastic hammer is not available use an old toothbrush handle (or some plastic item) as an absorber. Simply put pin into the hole as deep as you can with your fingers, put the toothbrush handle on split pin end and hit handle, not the pin.
Make sure that pin ends are flush with bracelet. If needed- hit few more times.
Job done!
If you do not want to do it yourself, any jeweler will do it in a matter of few minutes.
Don't forget to rate, please.

Mar 18, 2009 | Watches

1 Answer

Stainless steel band won't snap into my watch


Stainless steel bracelet ends (so called wings) must be curved flush to the watch case.
Another way is to use curved spring lugs (pins).

Dec 12, 2008 | Philip Stein Teslar Large Gunmetal Watch

Not finding what you are looking for?
Watches Logo

Related Topics:

385 people viewed this question

Ask a Question

Usually answered in minutes!

Top Gucci Watches Experts

Arturs Kalnins
Arturs Kalnins

Level 3 Expert

2338 Answers

NOEL
NOEL

Level 3 Expert

8537 Answers

Ngoro

Level 3 Expert

1767 Answers

Are you a Gucci Watch Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...