Question about Pioneer Car Audio & Video

Open Question

I have pioneer carrozeria avic-rz03 buttons not working but touch screen still working, how to find hard reset button factory reset button or how to fix it help me

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
bun-b6661
  • 5 Answers

SOURCE: Pioneer in-dash navigation system AVIC-D1

Hi, You set the screen so its all the way down and hold down the dvd eject then the reset button for a few seconds, then let off of the reset button, keep the eject button held down for another few seconds. Then the screen will say press reset. instead using the joystick, press up,up,down,down then push it in at the center. It will come up with options. the first one is touch screen test. using the joystick click on that one and do the calibration test. You will then have to trace the outline of the screen, while you are on the right side of it, trace it short to make up for the buttons on the right side. when you finish push the joystick in. it will say "settings ok" then go down to the 4th one, i think, and it will say something like test calibration settings and go to that one. It should say that the settings were saved. After that shut the key off and turn it back on and it should be good to go.

Posted on Aug 18, 2007

Ad
hogan doan
  • 227 Answers

SOURCE: Ipod problems with Pioneer AVIC-D3

Do you have an ipod module or are you using ibus-to-rca cable to connect your ipod to the D3? In order to control full ipod functions by touch screen you need the ipod module, hence the D3 says ipod control ready not ipod control built in. Let me know so I can pin point the problem.

Posted on May 02, 2008

  • 1 Answer

SOURCE: GPS touch screen not working

This works!!!! This saved me $200.00 I am eternally thankful! the key to it is pressing the little reset button. it is very small and only accessable with a pen. If you follow the directions as listed, it will work. I've been born agan for fixya!

Posted on Nov 20, 2008

  • 2 Answers

SOURCE: Touch screen not working...

Hi guys,

i post this solution for those wo will be in the same situation in th next future. I had the same problem with my HTC TyTN (Herm 200). The touch-screen was simply not working. I read many 'solutions' on the net but none worked. I did not try the hard-reset because i was convinced this is not a software problem, and resetting the WM5 will not help. So i brushed the corners, looked for small particles which were pressing on the cover of the touch screen. but it did not work. finally i found one post (i don't remember where exactly) where a guy used a credit card and pushed it all around the touch-screen under the metal case (a bit harder). i tried it and it worked. i pressed harder especially in the lower part, above the buttons. and simply it worked ! no problem since then.

Posted on Jan 25, 2009

  • 1 Answer

SOURCE: Pioneer Avic-F700BT worked perfectly fine for 7 months but....

Hello!
My pos just did this today after I got in a hot car (had windows up for security).
Symptoms:
Briefly displayed the PIONEER default splash screen, LED lighting was the default ... light/bright pink (to match pioneer?).
Then screen goes black, then backlight gets fully dimmed and LED dims to darks white (R,01G,01B01)

Wouldn't really respond to anything... but plays CD in background.

I had a brainstorm while sitting in my car at ACC (ignition) and reading the lame online TS guide.
I turned my car to ON and put the gear shift in REVERSE.
The screen flashed to the password, and flashed black again....
Some how the system stablelized after some time and I resurrected it*.

* After tinkering I found ALL settings except the NAV data/settings had been lost.
In addition I believe corruption has occured in the memory holding the voice data. TTS... that phone thing voice command wont display when i press down on the Multi-nav? dial. Also system crashes when I try to access language settings. Sometimes a Windows CE error message bled thru reporting a fatal application error. Illegal operation request...

Hope this helps. I think my POS is going back to cartoys before my 30days is up.
Pity

Posted on Jun 13, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Dear Sir/Miss/Madam, Is there any user's manual in English for this model :- Pioneer Carrozeria avic-z77?


Hi...Maybe this will help..Model # may be wrong..

http://www.fixya.com/support/t26130988-change_japanese_language_into_english How do change Japanese language into English language on my AVIC MRZ07...
The general consensus is that Pioneer Carrozzeria devices are usually intended for use in the Japanese market, if the language is already Japanese it probably cannot be changed to another language.

However, in general, when you reset a Pioneer device back to factory settings (the 'factory reset'), the first prompts received should be for
Language setting
Time setting
and so forth. So if you hard reset it, you should get a list of options to choose from, one of which would be either
'English'
or else the Japanese equivalent
'Eigo'.

So see if you can factory reset the device. This is, on Pioneer devices (generally speaking) done by holding down one button while powering the unit On... which button in this case? I am not sure (you have not stated which model of Carrozzeria device you have), but with the model # ***** could perhaps find out more specific information.

Jun 04, 2017 | Cars & Trucks

1 Answer

PIONEER CARROZERIA AVIC-DRZ99 ENGLISH MANUAL


Try Googling (pioneer)(AVIC-DRZ99)(manual) without parens. You may have to refine your search to get the manual in English.

Jul 04, 2013 | Car Audio & Video

3 Answers

Change language change from japanese to english on pioneer carrozeria HDD AVIC-HRZ88.( only display japanese on screen)


CHINESE MAKERS SHOULD LEARN HOW TO TALK/WRITE IN ENGLISH !!! Its driving us buyers insane !!! They sell their product in english countries and expect everyone to know their gibrish language

Nov 07, 2010 | Pioneer Car Audio & Video

1 Answer

I have a 2006 AVIC-D2 - navtraffic - pioneer. The right side of the touch screen does not respond to touch. The letters to the right of the screen when putting in an address, state etc do not respond to...


contact pioneer at 1-800-746-6337 for a authorized repair facility. I seen this problem on some unit's and needed to send them out for repair. i believe it was a $150 flat rate for repair

Jun 13, 2010 | Pioneer AVIC-D2 DVD Nav/6.5"...

1 Answer

GPS touch screen not working


This works!!!! This saved me $200.00 I am eternally thankful! the key to it is pressing the little reset button. it is very small and only accessable with a pen. If you follow the directions as listed, it will work. I've been born agan for fixya!

Jul 30, 2008 | Pioneer AVIC-D2 DVD Nav/6.5"...

1 Answer

Some buttons don't work


Pioneer AVIC-D1 Touch Screen Recalibration

If your pioneer AVIC car navigation unit does not register your touches or the wrong button is “pressed”, you need to re-calibrate your screen’s digitizer.

1-Hold the Eject button down until the face of the unit drops all the way
2-Using a pen hold down the reset button (just above the joystick) and the navigation disc eject simultaneously.
3-Release the reset button.
4-Release the dvd eject button next. The display will read “press reset”
5-Push the joystick up two times.
6-Push the joystick down twice.
7-Press the joystick in.
8-The service menu will appear after a short pause. You can navigate the service menu using the joystick.
9-Chose the first menu option and press in on the joystick.
10-Trace the screen with a stylus.
11-"P.ADJ" is the back button
12-Chose the second menu item in order to calibrate the touch screen. Use a stylus again and tap the "+" sign on the screen. (You may have to touch slightly off center if the digitizer is damaged. In which case things will still be off but it will be much better.)

Jul 27, 2008 | Pioneer AVIC-D2 In-dash Car Audio Stereo...

3 Answers

Recalibrating touch screen


Use the pin hole reset button. 

Oct 08, 2007 | Pioneer AVIC-D2 DVD Nav/6.5"...

7 Answers

Avic-N1 touch screen calibration...


1. Take disc out. 2. Press and hold eject and push the reset button. (don't release the eject button 'till screen closes and opens again. 3. Sceen will ask you to push reset.(don't) 4. With right knob... up,up,down,down,push 5. Perform steeps 1,2,3,and 4 only: The first outlines the screen The second has you push hash marks The third verifys The fourth Saves 6. Use "Band" buton for "back" 7. Press reset Be carefull......

Aug 07, 2007 | Pioneer AVIC-N1 Car DVD Player

Not finding what you are looking for?
Car Audio & Video Logo

Related Topics:

47 people viewed this question

Ask a Question

Usually answered in minutes!

Top Pioneer Car Audio & Video Experts

The Knight
The Knight

Level 3 Expert

76100 Answers

Marvin
Marvin

Level 3 Expert

85160 Answers

xxxxxx xxx

Level 3 Expert

5013 Answers

Are you a Pioneer Car Audio and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...