Question about Sharp Office Equipment & Supplies

Open Question

Booting delay on Sharp AR5316 - Sharp Office Equipment & Supplies

Posted by on

Ad

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
checkitright
  • 1362 Answers

SOURCE: sharp ar5316 blank pages printed and copied.

while standing in front of the copier open the Right door and then then flip down the Front door. Are the levers in place ? usually the front door will not close properly if not.

Second take out the toner and look for a loosely hanging piece of plastic on it, give it a tug, does it seem to be a long peice of clear plastic? if yes yank it all the way out. It is a protective piece sent for shipping. It will be on ALL the toners you get.

 

If not look at the right side door there is a back assembly there with either a black cylinder type roller or some strings.

Are the strings broken , is the roller in place?

Posted on Oct 25, 2007

Ad
  • 2072 Answers

SOURCE: sharp copier AR5316

H2 or 2H is related to a fuser under heat or overheat.
Try this first,

Performing a Fault Reset 14 will reset your WorkCentre and will help to clear error codes.

  1. Find the pink Clear button on the Control Panel of the WorkCentre.
  2. Find the button below the word Auto.
  3. Press these buttons in the following sequence: [Clear], [Auto], [Clear], [Auto] NOTE: All of the lights on the Control Panel should go out and the LED Display should go blank. If the lights do not go out, then repeat step 3 until they do. It may be necessary to increase or decrease the pace of the [Clear], [Auto], [Clear], [Auto] sequence.
  4. Press the [10's] key one time and the [1's] key four times to enter '14' in the LED Display, as if you were to make 14 copies.
  5. Press the green [Start] button.
  6. Press the pink [Clear] button two times.
  7. The WorkCentre should now warm up and come to ready.
  8. If the above steps do not clear the error code, repeat steps 3 to 6 a second time.
If this does not clear the problem the fuser will need replaced.

Posted on Feb 21, 2008

  • 7 Answers

SOURCE: SHARP AR5316 SHOWING PAPER WHILE NO PAPER JAM

try to chek if the actuator of the exit sensor is ok you will find it when you open the side door exactly attached to the heater try to check the end is it in plase or not if not use sim 30 sub1 to check all sensors you wil solve your problem

Posted on Mar 23, 2009

  • 41 Answers

SOURCE: h3 code in sharp ar5316

Heat roller abnormally high temperature
press:
# --> interrupt --> clear --> interrupt
14 --> start --> 1 --> start

Posted on Mar 12, 2013

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Drivers and software for SHARP AR 5316 windows 7 32


Sharp AR-5316 copier software doesnot support the window 7, it is suitable for window XP, Wndow 98/Me/2000/NT4.0

Mar 08, 2011 | Sharp AR-5316 Advanced Digital Imager...

1 Answer

Free xp driver for sharp ar5316 please!


Drivers for Sharp AR-5316 are available at Sharp Official Support site Click here and make selection as under: -

Select AR5316 > Windows XP

Good Luck!
Appreciate generously, if the solution could have been of any help!
CreativeTECH

Dec 19, 2010 | Office Equipment & Supplies

1 Answer

I want a driver 4 sharp ar5316 in ubantu ultimate edition 2.3


Hi there, Sharp AR5316 comes with installation CD when new. This gives those with computers a chance to use it as a printer only when they correctly install it. They quote several operating system that it can accommodate and unfortunately, ubuntu is not among them because it is only compatible with windows like windowsxp. For you to use it as a printer, please install windowsxp on your computer and follow the instructions on it. Best wishes.

Aug 03, 2010 | Sharp AR-5316 Advanced Digital Imager...

2 Answers

H3 code in sharp ar5316


It sound like you have a thermistor that either has a buildup on it or it is not contacting the fuser roller. I would remove the fuser, disassy and clean every component. Reinstall and usually the problems go away. Let me know if you need more assistance.

May 11, 2009 | Sharp AR-5316 Advanced Digital Imager...

2 Answers

SHARP AR5316 SHOWING PAPER WHILE NO PAPER JAM


try to chek if the actuator of the exit sensor is ok you will find it when you open the side door exactly attached to the heater try to check the end is it in plase or not if not use sim 30 sub1 to check all sensors you wil solve your problem

Mar 23, 2009 | Sharp AR-5316 Advanced Digital Imager...

Not finding what you are looking for?
Office Equipment & Supplies Logo

Related Topics:

23 people viewed this question

Ask a Question

Usually answered in minutes!

Top Sharp Office Equipment & Supplies Experts

Anthony Karuku

Level 2 Expert

267 Answers

amir hamza
amir hamza

Level 2 Expert

318 Answers

k24674

Level 3 Expert

8081 Answers

Are you a Sharp Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...