Question about Refrigerators

1 Answer

What type of light bulb goes in the door for the ice maker for model number MSD2432GR?

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    MVP:

    An expert that got 5 achievements.

    Habit-Forming:

    Visited the website for 3 consecutive days.

    New Friend:

    An expert that has 1 follower.

  • Contributor
  • 19 Answers

Night light bulb if your talking about the light for the dispenser. Inside the unit is 40 watt appliance bulb.

Posted on Jun 25, 2019

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
catriver
  • 878 Answers

SOURCE: Ice maker sotp making ice / red light blinking

J, As you open the freezer door the LED on the right should flash 2X with a pause repeatedly. When you hold the left side emmiter down the light should stay on steady. If you have this, you know the optics are good unless the ejector blades are not home. First thing to check is where the ejector blades on the ice maker are parked. They should be resting in the 2:00 position. If they are not, you could have a broken module. If they are in the 2:00 positon the next thing to check would be the fill tube. You want to make sure it is not frozen over. You can disconnect it from the back and see if you can blow through the line or visually inspect it. If all of the above mentioned check out, jump start the ice-maker. Remove the quarter inch screw holding the harness cover on the right side. Remove the harness cover. Pull the ice-maker straight out but be carefull not to smash the emmitter flap on the left side. Leave the harness connected. Get a jumper wire with the ends stripped apout a 1/4 inch. Unplug the refer and place the jumper in test holes T&H. Leave the jumper in and place the ice maker on the shelf where you can close the door. Close the door and plug the refer back in. Wait 30 seconds and open the door. The ice maker should be cycleing. Pull the jumper and place the module cover back on. Put the ice maker back in the rails. It should fill at approx the 12:00 position. Let me know how you make out. Catriver.

Posted on Jul 08, 2007

peyton32034
  • 410 Answers

SOURCE: Kitchenaid KSCS25 Refrigerator Ice Maker Inop

you should not be able to push the stripper at all so that tells me that the gear on the icemaker module is bad. get part number 8201515 and you should be fixed up.

Posted on Jan 07, 2008

duby1990
  • 370 Answers

SOURCE: ICE MAKER NOT WORKING

Check to make sure you freezer is at 0 to 5 degrees. If it is not the water valve to the ice maker will not even open.

Posted on Nov 20, 2008

jumptrout51
  • 3361 Answers

SOURCE: ice maker will not dispense the ice

The auger motor and coupling in the rear may be frozen and won't turn.
Remove the ice bin.
Place a screwdriver or similar device in the forks of the auger and twist counterclockwise till it moves. The replace the ice bin and try again.
It will be difficult to move.
If that does not work. Turn off the fridge and use a hair dryer to hrat the auger gear and motor till it frees up.

Posted on Mar 23, 2009

  • 1 Answer

SOURCE: door dhute not opening to let ice fall

on the right hand side of the door chute there is a little metal barrel that needs to be attached to the end of the arm that holds the ice door. this is attached to the spring that opens and closes the door chute.

Posted on May 06, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have Jenn-Air model number js2428gehb. Ice maker stuck on crushed ice. cube light flashes so does top green filter light.how do I fix this?


can you please look inside the door on the free sh food side and get the model number so I can see what type of ice maker assembly you have
Appliance 911 Sea Breeze

Aug 20, 2015 | Jenn-Air Refrigerators

1 Answer

I have a Whirlpool side by side fridge freezer with ice maker and water dispenser which is about 3 years old. Model number I think is WSC5533. Recently I had an interior lamp bulb blow in the fridge which...


HI,
You may have a failing door switch which is causing this problem, if you remove the bulb and close the door, the the red light out? If so, its possible you bulb is fine, you door switch has failed.
I hope this helps

I’m happy to help further over the phone at https://www.6ya.com/expert/gere_bf68e6055dd61249

Jul 26, 2011 | Whirlpool Refrigerators

1 Answer

The light in the fridge compartment....it is not the bulb. How do I remove the light housing......I found and removed the front screw but cannot disengage the rear part of the fitting.


Hi and welcome to FixYa. I am Kelly. It is difficult to answer your question without a model number because there are several types of light sockets in use. The majority of the sockets can simply be rotated 90 degrees and removed. Others have a locking tab that needs to be unlatched.
Before trying to rotate the light (expecially in the freezer compartment) make sure there is no ice build up around the socket. If there is ice.. use a hand held hair dryer or vacuum exhaust for an extended period to remove the ice first. If you still can not get it loose respond with a model number and I will look up the light socket to see where the locking tabs are. (Most of the time only one side has the lock tab and the other side is rotated up to remove it.)

Having said all of the above... I doubt the light socket is bad. Most light problems that persist after a bulb change are directly related to the door switch. Unplug the unit first then remove the light switch by sliding a thin knife blade on the side of the switch unlock the tab(s). The freezer light switch only has one tab while the fresh food compartment switch has two. Make a jumper for the 2 wires with an insulated wire and momentaily plug the unit in to check for a light. If you have a light the switch is bad. As for the freezer switch it has 3 wires you will need to look at the switch. It has 3 markings C, NO and NC. You will need to jumper from C to NC to get the light to work if the switch has failed. As long as one end of the jumper is on C you will not hurt anything if you jumper the wires incorrectly. One of the terminals powers the ice maker door closed (if you have an ice maker) and the other powers the light door open.

I think you have a door switch problem vs a light socket problem.

Here is a little about my experience:
http://blog.fixya.com/index.php/2010/05/award-winning-service

If you need more assistance / have any questions fee free to respond to this post.
Thanks for choosing FixYa, Kelly

Jul 13, 2011 | Refrigerators

1 Answer

Water does not come from the water dispenser and won't make ice and when I checked in the back I saw water halfway in the clear tube that goes into the refrigerator.....


Hi and welcome to FixYa, I am Kelly. Since you did not include your model number I have to respond in GENERIC terms. Open the freezer door and locate the light switch. Depress the light switch to make sure that the light is going off when the freezer door is closed. This light switch (with plunger) also turns off power to the water in door and the ice maker when the door is open. If the light stays on with the switch depressed it will not make ice or pass water through the door. The switch is removed by sliding a putty knife or thin knife blade on on side of the switch to release the locking tab. The switch will have 3 wires on it. C = (common / power) NC = ice maker and NC = light. There will only be continuity between C and either NO or NC depending on the plunger / actuator position. It will never read between all 3 contacts at the same time but C will always be one of the 2 test points. A replacement light / door switch is less than $10.00.

If you want more specific information or need further troubleshooting assistance after checking the door switch, please respond with your model number and I will gladly help you.

Thanks for choosing FixYa,
Kelly

Jan 05, 2011 | Maytag 25.6 cu. ft. Wide-By-Side...

1 Answer

Excess water delivered to ice maker


That will depend on type of ice maker and model number of refrigerator. At times the water control valve will stick because of age or just leaking while off like a dripping faucet. Can you find model number of your whirlpool? I do have some repair manuals for ice makers if they are not the electronic type. Sea Breeze

May 22, 2010 | Whirlpool 25.6 cu. ft. Side-by-Side...

1 Answer

Light will not work, ice maker will not work


OK, we need to know what door, freezer or fresh food section? Tell me that and I will trace it through the wiring diagram.Please confirm your model number? GD2SHGX Could be only the door switch. Sea Breeze

Apr 08, 2010 | Whirlpool GD2SHGX Refrigerator

1 Answer

I need the part # for the icemaker ordered


Now here is the confusing part. If your model number is a GE PDS22LBN the Ice Maker would be part number WR30X10039 for the model number posted above your post. If you have sears model number for the refrigerator it will be like 312.235698 for example. Confirm the model number of the refrigerator and I can tell you the correct Ice Maker part number. Thanks Sea Breeze

Feb 18, 2010 | GE PDS22LBN Bottom Freezer French Door...

1 Answer

GE ICE MAKER, VERY LITTLE ICE,


I had this problem with my GE ice maker not working and it was an unbelievably easy fix. If you have the same ice maker then you will see a green light by the power switch. Below the ice maker is a "paddle" ice sensor. The paddle is attached to the ice maker and there is a coil type tension spring. If your paddle is loose, make sure the end of the spring (the pointy wire end) is inserted into a small hole. You probably can't see the hole but move the wire end until it pops into the small hole. You should now have tension on the paddle. At this point I had heard that the freezer light bulb may be drawing too much current for the ice makers motherboard. I removed the bulb and, UNBELIEVABLY, the ice maker began making ice! Try removing or replacing the LIGHT BULB first!

Aug 02, 2009 | GE (PSS26MSRSS) Side by Side Refrigerator

1 Answer

Door dhute not opening to let ice fall


on the right hand side of the door chute there is a little metal barrel that needs to be attached to the end of the arm that holds the ice door. this is attached to the spring that opens and closes the door chute.

Apr 16, 2009 | Maytag MSD2732GR Side by Side Refrigerator

1 Answer

No ice through dispenser


When you operate the ice dispenser lever, you should be able to hear a little click from a micro-switch that then switches the auger motor and the light on and also opens the flap. If you cannot hear this small click, then the micro-switch is faulty. The ice dispenser only works when the freezer door is closed, so you could also inspect the door light/fan switch for proper operation.

Oct 30, 2007 | Kenmore 5553 / 655532 / 55534 / 55539 Side...

Not finding what you are looking for?
Refrigerators Logo

Related Topics:

59 people viewed this question

Ask a Question

Usually answered in minutes!

Top Refrigerators Experts

Marvin
Marvin

Level 3 Expert

85160 Answers

Brad Brown

Level 3 Expert

18072 Answers

Gil Shultz

Level 3 Expert

3388 Answers

Are you a Refrigerator Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...