Question about Kenwood Car Audio & Video

1 Answer

Kenwood dpx-u5120 Up to standby. Pressing the reset button will not disappear. What should I do?

Posted by Anonymous on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    New Friend:

    An expert that has 1 follower.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 124 Answers

Try unpluging the unit for about five minutes then try again

Posted on Jul 11, 2019

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
ryanriopel28
  • 130 Answers

SOURCE: kenwood dpx 4020

The iPod will stop itself from charging when the battery is full, and will not overcharge. I'm pretty sure you can't disconnect the power to the iPod (would stop it from charging) and still use the Audio to your stereo.

Posted on Aug 19, 2007

  • 1 Answer

SOURCE: USER MANUAL FOR A KENWOOD DPX 5000 DOUBLE DIN CAR STEREO

hi
i want rest code kenwood dpx 5000 car tape plz reply mee with master rest code
thanksssssssssssss

Posted on Apr 26, 2009

smartr10U
  • 1305 Answers

SOURCE: Require a English User Manual for a Kenwood Car Audio

Visit HERE and enter the various model numbers and you'll get free manuals in pdf.

K

Posted on Sep 16, 2009

  • 1 Answer

SOURCE: kenwood DPX 9000 MJ CDplayer

Start type the code on the face preset button only 1 to 4 to let it appear this number start from 3110 and press Play/Pause button. do itz until it's get to 3119.... the code is 3112 but it'z quite hard....

maybe ur rite!! solution num 2, put it in the trash!!!!

Posted on Nov 12, 2009

  • 1 Answer

SOURCE: kenwood dpx-501

I just solved the problem with my kenwood dpx mp 2090U - (looks similar with 501). FL Display with single CD, USB, 2 Din.
I should share this......... as I received the clue from someone that share the same case to me . Thanks to Mr,Nasirbaek from Indonesia,
The problem is at the main board . Dry (bad) soldering occurred. There are more then 5 resistors in series configuration. The resistor is quiet big (1.5mm x 3.5 mm, surface mount type R) about 2,7Ohms.The position is start from near usb port cable and ended to near big transistor (1 x 1.5 cm power transistor). After resoldering check with multitester to make sure that all R are connected in series configuration.
Just open 3 screws to access the main board. 1 at the top case. 2 at cd assembly, then Carefully take out the CD and the CD ribbon cable.
good luck.

Posted on Feb 21, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Wiring set up


The wiring diagram is on page 53 of this manual.

Apr 13, 2013 | Kenwood Dpx-u5120 Double Din Mp3 Cd Ipod...

3 Answers

Hi i have a kenwood hdv 910 car sterio and i do not have the code key cod for it.


you can send your stereo back to Kenwood to have the security code reset.

Oct 19, 2008 | Kenwood Car Audio & Video

1 Answer

How can i adjust the AM/PM in How can i adjust the AM/PM in Kenwood of DPX-U5120


It is not possible because it uses HH:MM format (a common format in audio track time)

Jan 22, 2013 | Kenwood Dpx-u5120 Double Din Mp3 Cd Ipod...

1 Answer

Dpx-u5120 dosent show subwoofer option in function mode , how to fix it ?


I manage to slove to my DPX-U5120 Subwoofer level adjustment. In STANDBY mode, Press the Main Volume button and turn to Setting, turn until you find the SW Preout, Swith to normal mode, its won't work if u switch to REAR

Go back to CD/USB Mode, Then Press the Main Volume and find Audio Adjustment and now u can find the Subwoofer Level , Sub Phrase and Sub LPF adjustment.. Um Glad i found this and Happy Setting

Mar 22, 2012 | Car Audio & Video

1 Answer

Just brought the kenwood dpx u5120 car radio and the manual is not in English, just wondering if u can send me a English version or just steps to setting the clock?


To adjust the clock. All you do is hold down the bass boost button untill the clock flashes, then use the volume button to adjust the time and the forward and reverse buttons to switch between minutes and hours. When your finished setting the time just press the bass boost button again to finish.

Jun 19, 2011 | Car Audio & Video

1 Answer

Code to unlock a kenwood dnx5140 car gps sterio


ype 1

  • During the code request mode, while pressing the DISP key, press and hold the Volume UP or DOWN key for 3 seconds until the "..." display disappears.
  • Enter the security code with the Kenwood remote.

Type 2

  • Press the "Auto" button and "Track up" on the face of radio at the same time until the four dash lines disappear.
  • Enter the security code with the Kenwood remote.

Type 3: Model# DPX-4020 and DPX-4030

  • Press and hold the 1 then the 6 preset keys until the display shows the letter C.
  • Enter the security code with the Kenwood remote.
Entering Letters with a Kenwood Remoteo enter a letter with a Kenwood remote, press a button once for the first letter, twice for the second letter, and three times for the third letter. Press the Track Up or Next Track key to send the letter. To send the letter A, press the 2 key once then press the Track Up key. To send the letter B, press the 2 key twice then press the Track up key.
Finally, when all of the letters are entered, press and hold the Track Up button for 3 seconds.
The key sequence to enter the security code KCAR is:
  • 5
  • 5
  • Track Up
  • 2
  • 2
  • 2
  • Track Up
  • 2
  • Track Up
  • 7
  • 7
  • Track Up
The Kenwood should then enter tuner mode.
A Security Code Bug in Some Kenwoods

Oct 31, 2010 | Kenwood DNX5140 Car GPS Receiver

1 Answer

Disconnected battey, new battery, no aux


Common Kenwood Security Codes
Many Kenwood radios are configured with the same security codes:

KCAR - This seems to be a "backdoor" to some Kenwood models.
3051 - This is the security code which is printed in the manual of many Kenwood models.
1234 - This is a security code commonly chosen by Kenwood owners.
Entering Your Kenwood Security Code
If the car battery fails or is disconnected, the Kenwood will ask for the security code.

The procedure to enter your security code differs on various models of Kenwood car stereos. Here are three of the more common procedures:

Type 1
During the code request mode, while holding the DISP key depressed, press and hold the Volume UP or DOWN key for 3 seconds until the "..." display disappears.
Enter the security code using your Kenwood remote.
Type 2
Press the "Auto" button and "Track up" on the face of radio at the same time until the four dash lines disappear.
Enter the security code using your Kenwood remote.
Type 3: Model# DPX-4020 and DPX-4030
Press and hold the 1 then the 6 preset keys until the display shows the letter 'C'.
Enter the security code using your Kenwood remote.
Entering Letters on your Kenwood Remote
To enter a letter using your Kenwood remote, press a button once for the first letter, twice for the second letter, and three times for the third letter -- then press the Track Up or Next Track key to send the letter.

To send the letter 'A', press the 2 key once and then press the Track Up key. To send the letter 'B', press the 2 key twice and then press the Track up key.

Finally, when you are done entering all of the letters, press and hold the Track Up button for 3 seconds.

The key sequence to enter the security code KCAR is:

5
5
Track Up
2
2
2
Track Up
2
Track Up
7
7
Track Up
Your Kenwood should then enter tuner mode.

A Security Code Bug in some Kenwoods
There is a reported bug in the security code handling of some Kenwood stereos. In models with thie bug, the security code is stored incorrectly. The workaround is to enter the wrong security code.

In models with this bug, you have to decrement the third character of the security code by one. If your security code was 1111, you would enter your security code as 1101. If your security code was 9999, you would enter 9989.

Jun 09, 2009 | Kenwood KDC-MP2035 CD Player

2 Answers

Aux input. Kenwood ecelon dpx-701


You have to go into the menu and turn it back on. It is in the menu under "built in aux" and just switch it to on.

Feb 27, 2009 | Kenwood Excelon DPX-701

30 Answers

Forgot my code.


What button should I push if I don't have an "auto" button, both on the remote or the head unit? I have a dNx-5140. All help would be appreciated.

Aug 27, 2007 | Kenwood KDC-MP4028 CD Player

Not finding what you are looking for?

Open Questions:

Car Audio & Video Logo

Related Topics:

49 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kenwood Car Audio & Video Experts

xxxxxx xxx

Level 3 Expert

5013 Answers

Marvin
Marvin

Level 3 Expert

85160 Answers

Mike Duncan
Mike Duncan

Level 2 Expert

219 Answers

Are you a Kenwood Car Audio and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...