Question about Russell Hobbs Coffee Makers & Espresso Machines
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
Here's a link to this great service
Posted on Jan 02, 2017
Ask the breadmaker manual search engine:
If they find it, they will provide you a direct download link.
Posted on Sep 09, 2010
SOURCE: E8 error code
8E - OVER CURRENT ERROR
IPM fault signal (this is caused by the overload of the MICOM INTO during motor action).
IPM: Integrated power module. The IPM controls the motor.
If the fault (low signal) happens to be sensed even once during the washing/rinsing stage, the motor stops immediately. However, during the dehydrating stage the signal is to be sensed, when the number of signals reads more than 6 per 500ms during the Washing or Rinsing cycle action.
If the motor stops working, in one direction ten times, "8E" Error is displayed.
During dehydrating, when the overload is sensed, the motor stops working at once and then feeds back to the initial stage of the dehydration unbalance sensing. When the feed back has occcurred twice, Error "8E" is displayed during the dehydrating unbalance sensing, No error happens by overload sensing. When it happens at more than 800rpm, the process is stopped compulsorily. Power Switch OFF can clear the overload error.
Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question
Posted on Sep 15, 2010
SOURCE: I have lost the manual
Hi from retired Englishman in SW France,
Methinks you could do with another manual for your washer- for now and probably later! Sorry but FixYa cannot do that direct - members of the forum are just people from all over the world, probably working from home, and not representing any particular manufacturer ;-0)
By the way normally a spin speed is a spin speed regardless of whether there are whites or others inside. It really depends on the material which is being spun as to how much is spun out and drained. If the maximum spin speed has not spun all of the water out another spin is not likely to either - just waste electricity ;-0(
If your garments are still wetter than you would expect after spinning it COULD be that there is water still left in the drum i.e.not completely drained because of a blocked filter/drain pump. If this is so come back to me and I will send you my pre-typed guidance notes on cleaning/clearing blocked filters/drain pump/motors.
You will need to type into your search engine/web browser '(make model number) washer manual' and you should be presented with a number of sources from which you can either download for free or have to pay a nominal amount.
You could also try the manufacturer's web site direct ;-0)
If this has assisted you please consider a 4 thumbs up for the rating.
Thanks and good luck!
Posted on Sep 03, 2011
See the diagram attached:
You will see the fuse you will problema 1) Ground 2) Live wire touching the chassis 3) Heating elements in short 4) Control Relais in short. 5) Test Diodes,You must test every components.God bless you
Posted on May 19, 2012
Tips for a great answer:
Sep 02, 2018 | Russell Hobbs Kitchen Appliances - Others
Aug 10, 2018 | Russell Hobbs Washing Machines
Aug 10, 2018 | Russell Hobbs Kitchen Appliances - Others
Aug 08, 2018 | Russell Hobbs Kitchen Appliances - Others
Apr 28, 2018 | Russell Hobbs Coffee Makers & Espresso...
Aug 05, 2016 | Russell Hobbs Washing Machines
Jan 13, 2016 | Russell Hobbs Kitchen Appliances - Others
Mar 13, 2015 | Daewoo Washing Machines
Nov 06, 2013 | Russell Hobbs RH1042 Frontload Washing...
Oct 24, 2013 | Russell Hobbs RH1042 Frontload Washing...
41 people viewed this question
Usually answered in minutes!
Level 3 Expert
Level 2 Expert
Level 3 Expert
Step 2: Please assign your manual to a product: