Question about Pioneer Car Audio & Video

Open Question

Where to get a dual volume pod for a pioneer kx440 amplifier.. Thanks Trevor.

Posted by on

Ad

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
  • 1 Answer

SOURCE: two amplifier installation

not 100% sure but i think it is because your tryin to pull 2 much power from system try unbridgeing them

Posted on Feb 20, 2008

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I would like to add my i-pod to the receiver so i could listen to the music what kind off cable would i need


An i-pod provides a standard headphone level output. The AVR-1803 has nine RCA stereo inputs that will accept the signal from the i-pod. You need a 3.5mm stereo TRS plug on one end and two RCA plugs on the other end to connect your i-pod to your amplifier. Note: Be careful to select a 3.5 mm plug that has a slim enough plastic moulding to fit into the i-pod headphone output. On your amplifier you simply select the analogue input that you have chosen to use. Be careful of levels when you are setting up. Set the volume of your i-pod to about 50% and set the input sensitivity to zero, press play on your i-pod and gradually increase the gain on your amplifier input. Hope this helps, Don.

Dec 08, 2013 | Denon AVR-1803 Receiver

1 Answer

My pioneer pl-200 doesn't play loud enough through my pioneer vsx-521-k receiver


The PL-200 has no pre amp and your VSX-521 has no phono input. You need an RIAA preamp.

Jul 11, 2017 | Pioneer Vsx-521-k 5.1 Channel A/v Home...

1 Answer

I wired my dvc sub woofers to 4 ohms and bridged my pioneer gm-5400 amp and it cuts off when i turn the volume up.


1. Check if your power cable is of adequate Gauge 2. Try turning the volume down from the amplifier gain level 3. You could even check to see if your battery is on it's way out and just cant feed the amplifier with the power it needs. (very rare case) do the car lights dim when the volume is not really that loud? 4. There could be an error on the way the subs are connected, double check that you have absolutely configured them to run @ 4OHM. could be checked with a multimeter before connecting to the amplifier. 5. Another rare case is sometimes the fuse block expands when it heats up on loud volumes and can have contact issues so try tightening the socket that the fuse goes into. 6. It could also be a problem with one of the sub woofer or even the amplifier. more details might help me better understand the problem, but i hope this helps. dreamsystems

Feb 06, 2011 | Pioneer GM5400T 2-Channel Bridgeable...

1 Answer

Is there a lead you can buy so i can connect my ipod to an amplifier


Yes just connect the one below to the headphone socket of the I-Pod.

d7e400c.jpg3.5 Jack to two RCA jacks

May 10, 2010 | Pioneer A109 2-Channel Amplifier

1 Answer

Which terminals to use


if your amplifier is 2 ohm mono stable - you can wire them in parallel.
Put a piece of wire from one + terminal to the other + terminal on the subwoofer.
Then do the same to the -.
Now pick one pair of teminals from the subwoofer and wire it to the amplifier. (one set of subwoofer terminals will have 2 wires each).
If you reply with your amplifier make/model, I can tell you the best usage.

Thanks for using FixYa - a FixYa rating is appreciated for answering your FREE question.

May 30, 2009 | Pioneer TS-W307D4 Car Subwoofer

1 Answer

My pioneer 600w amplifier cuts at high volume...


this means that the enternal preamp is starting to fail eventualy it will make no sound at all if you would like you can use a 4 channel amplifier if you would like to keep this deck

Feb 05, 2009 | Pioneer GM-6300F Car Audio Amplifier

1 Answer

Pioneer deh-2000r cd tuner


The volume + switch may be stuck. Does the Vol+ switch click like the other switches or does it feel like the switch has collapsed?

Sep 18, 2008 | Car Audio & Video

1 Answer

My car stereo shuts off when i adjust the volume of my amplified subwoofer


your power suplly is either not good meaning the power cable is too small or you don not have enough ground. try adding a bigger cable for ground and power (dc).

Aug 12, 2008 | Pioneer MONO CAR AMP 1000W X 1 Car Audio...

1 Answer

Pioneer amplifier 1980's


bias can be out in shape of volume written bias-or it can be in printed circuit board as potentiometer labeled by bias word.

Nov 08, 2007 | Audio Players & Recorders

Not finding what you are looking for?
Car Audio & Video Logo

Related Topics:

23 people viewed this question

Ask a Question

Usually answered in minutes!

Top Pioneer Car Audio & Video Experts

The Knight
The Knight

Level 3 Expert

76100 Answers

Marvin
Marvin

Level 3 Expert

85160 Answers

xxxxxx xxx

Level 3 Expert

5013 Answers

Are you a Pioneer Car Audio and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...