Question about Kenmore Refrigerators

Open Question

I have a kenmore cold spot model # 106.56542400. I touched the metal measuring rule to the outlet plug and now the light will not go on.

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
Master_Tech
  • 770 Answers

SOURCE: Kenmore cold spot refrigerator freezer

wow you have power to the unit what about the temp control ? is it turned up?? if so is it closed(calling for cooling?) that is the place to start you can jumper it after yo unplug it to see if you dont have a meter

Posted on Jan 24, 2008

Ad
localwonder
  • 6784 Answers

SOURCE: Power to the outlet, but apparently no power at the touch pad - it is non responsive with no indicator lights on.

1. No power to the washer
Make sure there's power getting to the washer. Check for a tripped circuit breaker or a blown fuse. Check the wall socket for power. Sometimes the power cord disconnects at the washer, if this is the case, the wiring must be repaired or replaced.

2. Lid switch
The washing machine may not function if the lid switch is defective. The switch is usually located near the door. Replace if found defective.

If all the above checks out OK, replace the touch pad.

Posted on May 30, 2009

redbeard00
  • 957 Answers

SOURCE: TTR 90 wont start. Not carb. Not CDI. Plug cap?

Every component plays a part in the ignition system. Check the wiring as you go. Start at one end and move forward. You have done a lot of work so far. so you should be close. If the igniter is fine and the other components too. Then it would narrow it down to an electrical problem or no signal/pulse to the coil. See if the coil is receiving that pulse. you can use a test light for this test. Pos. will be power and NEG. will be the pulse. With light on the NEG. crank the engine over and see if it flashes. Let me know how its going.

Posted on Jun 01, 2009

  • 89 Answers

SOURCE: Refrigerate not working freezer not working

sounds like the relay is bad replace the relay this should take care of the problem it is located on the compressor

Posted on Jul 11, 2009

  • 117 Answers

SOURCE: I have a kenmore cold spot refriderator not cooling

Since the compressor is not hot to touch, I would bet that the relay /overload assemby on the compressor terminals are defective.This is a common problem on refrigerators that can be fixed with a few simple tools. I recommend a 3 in 1 start kit that is easy to retrofit. Start by removing cover off compressor. Read intructions on kit to hook up three wires to terminal s,r, and c. Next cut the black wire feeding power to compressor and hook to one line of kit. Cut white common wire and hook to other line of kit. Place the kit off to the side of compressor and reinstall the cover. Plug frig back up and compressor should run if installation is correct. Hope this helps

Posted on May 17, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Horn goes off on cold nights on 1998 gran am


problem in horn pad..no dought..common. problem

Oct 01, 2012 | 2002 Mitsubishi Montero

1 Answer

Everything is working but fan in frezer everything in bottom not getting cold it is a o5 model the name is kenmore cold spot model #106.74254400 type 22tfa


If understand your problem as being a bad fan in the freezer. Take the plastic or metal panel off that covers the back of the freezer. Inside you will see a fan that is held on by two or 3 screws 10mm or 5/16. Unplug the wires to the fan and remove the screws. This is an easy fix just make sure you unplug your fridge first. Hope this helps you.

Aug 18, 2010 | Kenmore Refrigerators

1 Answer

I have a kenmore cold spot refriderator not cooling


Since the compressor is not hot to touch, I would bet that the relay /overload assemby on the compressor terminals are defective.This is a common problem on refrigerators that can be fixed with a few simple tools. I recommend a 3 in 1 start kit that is easy to retrofit. Start by removing cover off compressor. Read intructions on kit to hook up three wires to terminal s,r, and c. Next cut the black wire feeding power to compressor and hook to one line of kit. Cut white common wire and hook to other line of kit. Place the kit off to the side of compressor and reinstall the cover. Plug frig back up and compressor should run if installation is correct. Hope this helps

May 17, 2010 | Kenmore Refrigerators

1 Answer

My Kenmore series 80 washer's cold outlet doesn't work


Hi, It does sound like the inlet valve is bad. If the screen inside the inlet vavle is not plugged, you will most likely need to change the valve. If you will send me a model #. I can tell you how to get to the valve for replacement.

Thanks
Vic

Jul 26, 2009 | Washing Machines

1 Answer

Refrigerate not working freezer not working


sounds like the relay is bad replace the relay this should take care of the problem it is located on the compressor

Jul 11, 2009 | Kenmore 55612 / 55614 / 5561 / 655619 Side...

1 Answer

Got a 62600 dryer and the power wont come on got power to the unit


Working with live electrical current can be very hazardous. Testing voltage output requires working with electrical current. Do not attempt this measurement without the proper tools and safeguards
.
To measure the voltage at an electrical outlet requires the use of a multimeter. Always test your test equipment for proper operation before use.
Set the multimeter to AC voltage. The markings may appear as VAC, AC V, or a V beneath a wavy line. Choose the AC voltage closest to the voltage you will measure. Standard current in home and businesses in the USA is in the range of 110 to 120 volts. Some circuits used for equipment such as dryers, air conditioners, electric stoves, ovens and other large equipment may use voltage in the range of 220 to 240 volts. These heavy-duty circuits can be identified by their non-standard outlet plugs.
While grasping the insulated portion of the probes (never touch the metal conductor during testing) place one probe into each of the two terminals. The multimeter will display the voltage.
Carefully remove the probes, being careful not to touch the metal part of the probes to anything or each other.
The voltage should typically test in the range of 108 to 121 volts for most circuits. If voltage is higher or lower, professional electrical service may be required.


Good luck;

Regards:
VOTIT

Dont forget to rate;

Jul 05, 2009 | Kenmore Dryers

1 Answer

I have a Kenmore Cold Spot Model 70192000. Having


HI, I can help you with this. It sounds like the defrost drain is plugged. If you will get me the model# from inside the fresh food section of the refrigerator, I can look up this model and instruct you on how to repair this.

Thanks
Vic

Jun 08, 2009 | Kenmore 50522 / 50524 Side by Side...

2 Answers

Usage How To


To measure the voltage at an electrical outlet requires the use of a multimeter. Always test your test equipment for proper operation before use. Set the multimeter to AC voltage. The markings may appear as VAC, AC V, or a V beneath a wavy line. Choose the AC voltage closest to the voltage you will measure. Standard current in home and businesses in the USA is in the range of 110 to 120 volts. Some circuits used for equipment such as dryers, air conditioners, electric stoves, ovens and other large equipment may use voltage in the range of 220 to 240 volts. These heavy-duty circuits can be identified by their non-standard outlet plugs. While grasping the insulated portion of the probes (never touch the metal conductor during testing) place one probe into each of the two terminals. The multimeter will display the voltage. Carefully remove the probes, being careful not to touch the metal part of the probes to anything or each other. The voltage should typically test in the range of 108 to 121 volts for most circuits. If voltage is higher or lower, professional electrical service may be required.

Aug 27, 2008 | IDEAL Powr-Glo Audible Voltage Tester

Not finding what you are looking for?
Refrigerators Logo

Related Topics:

42 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kenmore Refrigerators Experts

Fred Sops

Level 2 Expert

351 Answers

Audrey Messer
Audrey Messer

Level 2 Expert

182 Answers

John Tripp
John Tripp

Level 3 Expert

4656 Answers

Are you a Kenmore Refrigerator Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...