Question about Sharp Office Equipment & Supplies

2 Answers

Sharp h4 code - Sharp Office Equipment & Supplies

Posted by on

Ad

2 Answers

  • Level 1:

    An expert who has achieved level 1.

    New Friend:

    An expert that has 1 follower.

    Corporal:

    An expert that hasĀ over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 6 Answers

Fuser error clear 14

Posted on Jul 12, 2019

Ad
  • Level 1:

    An expert who has achieved level 1.

    MVP:

    An expert that gotĀ 5 achievements.

    New Friend:

    An expert that has 1 follower.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Contributor
  • 82 Answers

# * C * to get into simulations mode 14 start button 1 start button, or execute then yes, to reset machine. You might, depending on model, push the CA button to reset the machine.

Posted on Jul 14, 2019

  • David Wylie
    David Wylie Jul 14, 2019

    # * C * to get into simulations mode 14 start button 1 start button, or execute then yes, to reset machine. You might, depending on model, push the CA button to reset the machine.

×

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

  • 146 Answers

SOURCE: Sharp AR-M237 Error Code H4-21

-H4-21 means:Sub heater lamp abnormally low temperature detection. The setup temperature (about –25°C: Sim 43-1-1) is not reached within the specified time (about 32sec) from turning on the power ON SW. (When the temperature falls below 140°C in the standby mode.)
-Causes:
Sub heater thermistor defect
Sub heater lamp failure
Sub thermostat failure
Control PWB failure
-Check the sub heater lamp blinking with SIM 5-2-2.
When the lamp blinks normally: Check the thermistor and the harness. Check the MCU PWB thermistor input circuit.
When the lamp does not light: Check for disconnection of the heater lamp and thermostat. Check the interlock switch. Check the power PWB and the MCU PWB lamp control circuit.
Clear the display of self-diagnostics with SIM 14.
The H4 errors will not reset by themselves. You must enter service mode to reset this error even if the problem has been repaired. The reset process is outlined below (DO NOT USE ANY OTHER FUNCTIONS IN SERVICE MODE):
Press the following sequence: "#/P" "*" "C" "*"
Type in 1 4
Press start
hit 1 for yes
hit start
Unit should power off and the restart.
If the error code recurrs ther are other problems.

Posted on Jun 06, 2008

  • 62 Answers

SOURCE: Error code H4-01

This mean you have low temp. on heat lamp 2 program interput clear interrupt 14 print may clear this code. if not you can look at the fusing unit and reset thrmo breaker that may be pop off.

Posted on Jul 30, 2008

  • 62 Answers

SOURCE: SHARP AL-1216: HOW TO REMOVE H4 ERROR CODE

www.tinli.com.hk/PDF/AL1216.pdf

Hope this helps.

paul

Posted on Nov 02, 2008

  • 1 Answer

SOURCE: sharp al2030 error code h4 upon power up

Here is the solution straight from the lips of tec support at sharp.

This can happen due to a power outage.

Here is how you fix it.

1. Hit clear, then auto. (clear is on the right the red C, auto is on the far left)
2. Once again Hit clear, then auto. (clear is on the right the red C, auto is on the far left)

At this point wait for the screen to go dark.

3. Type in 14 (hit the 10 once an the 1 button 4 times)
4. Hit the Green Button.

The screen will go dark and reset the copier.

Posted on May 18, 2009

  • 7 Answers

SOURCE: I have a sharp copier, model AR-285, H4-01

H4 error pertains to lamp errors.

that would either be the copy lamp or the heater lamp.

check both lamps.

with heater lamps,it's usually caused by either a broken heater lamp or a dirty thermostat on the heater roller assembly.

Posted on Jun 10, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

6 Answers

Sharp ar 5516 printers error h5. h4


hi,I have error code L h on my coppier sharp 5516. your help please.

Aug 05, 2010 | Sharp AR-5316 Advanced Digital Imager...

3 Answers

I have a sharp copier, model AR-285, H4-01


H4 error pertains to lamp errors.

that would either be the copy lamp or the heater lamp.

check both lamps.

with heater lamps,it's usually caused by either a broken heater lamp or a dirty thermostat on the heater roller assembly.

Jun 09, 2009 | Sharp Office Equipment & Supplies

4 Answers

Code H4 comes up when the sharp copier ar-5316 is switched on. it cannot be use. what shall I do to solve this problem of error code H4.


Hello sir; H4 code require reset procedure as follow;
1, press"#" "interupt" "c" "interupt" these 4 keys.
2, enter 14 , then press start
3, turn power off and back on .

Jan 28, 2009 | Sharp AR-5316 Advanced Digital Imager...

1 Answer

Code H4 is showing on the machine


h4 code in sharp .that s fuser temperature very high .just reset it.press clear key,auto photo key,clear,auto photo key.copier goes dead .when it goes dead just press 14 then start key.copier will bi ready after some time.it works.by mian jee

Dec 17, 2008 | Sharp SF 2020 Copier

1 Answer

What does H4 mean on a Sharp SF71 electrostatic copier?


What does code:H4-00 means on a Sharp AR-M450?

Nov 15, 2008 | Sharp AR-M237 Copier

2 Answers

SHARP AL-1216: HOW TO REMOVE H4 ERROR CODE


www.tinli.com.hk/PDF/AL1216.pdf

Hope this helps.

paul

Nov 01, 2008 | Office Equipment & Supplies

2 Answers

SHARP AR C250 Digital Color COPIER HAS SERVICE CODE H4 00


Press P-interrupt-C-interrupt and enter test command 14 and Execute to clear your error. Let your machine reboot. If it comes back you have a problem with your fuser. Most likely it's dirt or toner caked on your tempature sensors and they need to be scraped off.

Mar 17, 2008 | Sharp AR C250A Color Copier

4 Answers

Sharp ar-5316


I am getting a problem code H4 for sharp copier when i start the machine. what is the problem. is ther any solution for the problem of the said model.

Aug 28, 2007 | Sharp AR-5316 Advanced Digital Imager...

Not finding what you are looking for?
Office Equipment & Supplies Logo

Related Topics:

26 people viewed this question

Ask a Question

Usually answered in minutes!

Top Sharp Office Equipment & Supplies Experts

Anthony Karuku

Level 2 Expert

268 Answers

amir hamza
amir hamza

Level 2 Expert

318 Answers

k24674

Level 3 Expert

8081 Answers

Are you a Sharp Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...