Question about Ricoh Office Equipment & Supplies

Open Question

Error sc547 for rico aficio

Solution for ricoh 270, error 546

Posted by on

  • Edward Martin
    Edward Martin Jul 19, 2019

    Hi theodory jeremia dizange, I want to help you with your question, but I need more information from you.
    Please Call Customer Service & Support For Help Call 1 8O5*465*751O Toll Free 24x7

×

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
  • 86 Answers

SOURCE: My Rico Aficio 200

Please open the front door and turn the blue lever in the middle,
remove the Transfer and Separation unit and check if the bushings of the transfer roller are damaged.
If OK, please give some oil on the shaft/bushings of the transfer roller. This unit may be replaced as a whole unit.
If SC401 re-occurs, please check the Photoconductor unit (drum).

Posted on Jan 13, 2009

Ad
  • 95 Answers

SOURCE: RICO AFICIO 6010 KEEPS PAPER JAMMING,AND THE RIP

The Rip needs the system software reinstalled. The jamming could be anything, need more info.

Posted on Jun 22, 2009

dante777
  • 623 Answers

SOURCE: eror sc547

The error sc 547 refers to a "Zero cross signal malfunction".

This means that the applied power supply AC frequency was detected at over 66Hz or below 45Hz, and the zero cross signals are not detected within a certain period within 500 ms after the main power switch has been turned on.

Possible causes are:
- Power supply board defective
- IOCSS defective
- BICU defective

Try to reset the SC code by entering SP5810 and select 1.
Then hold down the photo mode key and the # key at the same time for at least 3 second.
Then turn the machine off and on again.
If the same issue still appears, try to replace the Power Supply Unit.

Posted on Jul 05, 2010

  • 1 Answer

SOURCE: error code facsimile error red wrench sc547 ricoh

functional problem sc 547

Posted on Jul 08, 2011

  • 3 Answers

SOURCE: AN SC547 ERROR ON MY

547 D Zero cross error § The zero cross signal is detected three times even though the heater relay is off when turning on the main power. § The zero cross signal is not detected for 2 seconds even though the heater relay is on after turning on the main power or closing the front door. § The detection error occurs twice or more in the 11 zero cross signal detections. This error is defined when the detected zero cross signal is less than 45. § Defective fusing lamp relay § Defective fusing lamp relay circuit § Unstable power supply 1. Check the power supply source. 2. Replace the PSU

Posted on Jul 28, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Why error SC547 on ricoh aficio 4501 repeating its self after resetting?


Fixing problem. You have a bad thermistor. This detects heat in the fixing assembly. There are two . Replace both.

Jun 08, 2017 | Ricoh Office Equipment & Supplies

1 Answer

Help with error code SC547-01


sc 547 mean fixing unit error ,you can reset by simply getting into simulation mode and then switch off an the machine ,getting into the simulation mode is simply by pressing 107 and press and hold c ,

Jun 19, 2013 | Ricoh Aficio 450 Copier

1 Answer

Ricoh afico 811 error sc689 and sc547


sc547 is a power supply error that can mean you have a faulty power supply. The service manual does not list an sc689, and it's not in the help desk support database either... are you sure that's the code that comes on the screen?

Oct 05, 2010 | Ricoh Aficio SP C811DN-DL Printer

1 Answer

Eror sc547


The error sc 547 refers to a "Zero cross signal malfunction".

This means that the applied power supply AC frequency was detected at over 66Hz or below 45Hz, and the zero cross signals are not detected within a certain period within 500 ms after the main power switch has been turned on.

Possible causes are:
- Power supply board defective
- IOCSS defective
- BICU defective

Try to reset the SC code by entering SP5810 and select 1.
Then hold down the photo mode key and the # key at the same time for at least 3 second.
Then turn the machine off and on again.
If the same issue still appears, try to replace the Power Supply Unit.

Jul 04, 2010 | Ricoh Aficio MP 2000 Black and White...

1 Answer

Error sc547 aficio 180


Heat up failure in fuser area. Have tech check thermofuse and thirmistor for signs of wear or dirty

Jan 12, 2010 | Ricoh Aficio 150 Copier

2 Answers

Error code facsimile error red wrench sc547 ricoh aficio 180


there may be a problem with your electric supply(wall outlet) , wrong voltage or power supply bad

Jan 07, 2010 | Ricoh Office Equipment & Supplies

1 Answer

SC547


try to replace power supply

Apr 24, 2008 | Ricoh Aficio 1085 Laser Printer

1 Answer

Error sc547


Did you unplug any other wires by actcident or move some thing? was that problem there before. If not recheck what you did.

Feb 21, 2008 | Ricoh Aficio 450 Copier

2 Answers

Ricoh copier


Must have unplugged the thermister on the coupling connection bank. Reset fuser: Clear modes/ 107/ press and hold clear/stop. Pick copy sp. select mode. exit out of all screens and cycle power.

Feb 21, 2008 | Ricoh Aficio 450 Copier

Not finding what you are looking for?
Office Equipment & Supplies Logo

Related Topics:

18 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ricoh Office Equipment & Supplies Experts

gggg

Level 3 Expert

904 Answers

Adorjani Laszlo

Level 3 Expert

1316 Answers

quennie732

Level 2 Expert

422 Answers

Are you a Ricoh Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...