Question about LG Washing Machines

1 Answer

Lg front load washer machine model# WM2240CW tub is rubbing on the front gasket while in spin mode can someone possibly help me with answer

Posted by on

×

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • LG Master
  • 2,501 Answers

Most likely it is a broken 'spider'. That's the 3 armed part that holds the inner drum to the hub. Not uncommon. Can be expensive to fix. Can be done yourself. Check out videos on YouTube or repairclinic or appliancepartspros.

Posted on Jul 21, 2019

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
jsrock516
  • 5911 Answers

SOURCE: chenging the rubber gasket attached to kenmore H2e front load washer

The following link provides you with step-by-step instructions on how to change the door bellow:

http://www.fixya.com/support/r385210-replacing_door_bellow_kenmore_elite

This is not a difficult repair. Just follow the steps provided. If you have any questions, please let me know. I hope you find this information helpful.

Posted on Sep 02, 2008

  • 40 Answers

SOURCE: Loud noise during spin cycle

is it more like a roar or a train going by? if so your rear tub bearing is going out. very expensive have to replace the tub, basket, spinner ring and shaft and seals about 4 hrs for an exprienced tech to do took me 7 hrs to do for the first time. but it will be very close to $1000 to have done not much less to do it yourself.

Posted on Mar 10, 2009

  • 1 Answer

SOURCE: replacing door gasket on maytag neptune MAH5500BWW washer

I need to know what are the steps to replacing the door gasket, I would like to know what to take apart, and what not to take apart. Like a step by step lay out.

Posted on May 25, 2009

milten1
  • 1304 Answers

SOURCE: Maytag Neptune Front Load Washer Model MAH4000AWW low last spin

two problems here,
your shaft seal is running on its last leg
the sound is unmistakeable and always described the same...
the water issue, you probably have a trickle leak through the cold water valve
the mixing valve is quite an easy repair, but I would have to say with all honesty, it probably time for a new machine
the hub seal is a tub replacment call
2 hrs of labor if hes good
and the tub runs around 500.00 dollars
sory for the bad news

Posted on Oct 10, 2009

  • 4 Answers

SOURCE: LG Washer WM0642HW: Not enough water

Turn clockwise the water level sensor set screw a half turn "clockwise" under the top of the machine lid.This is the only way to rid yourself of the WICK WATER RUB WASH METHOD that is just terrible. Especially with a full load ! BELIEVE ME. I really wonder if consumers who have the WM0642HW earlier produced version with the nozzle spray system in the top of the door seal are having these troubles?. Mine is a 2009 verson of the WM0642HW, No Forced Water Recirculation. ( Discontinued) and how it was preset for fill at the factory made it perform terribly. Only after i adjusted the water level sensor does it perform well the first time around. Have yet had to rewash anything since the adjustment i made for the fill level. Good Luck.

Posted on Jun 20, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My LG front load washer doesn't spin as fast as it should (someone in my house OVER-filled it) and it seems to spin lop-sided. it still fills and drains properly. Any suggestion?


can you please give me the following information:
1] Is the inner tub ( the one that revolves when the machine is working) tilted and touching the outer tub ( the one the door rubber is fixed to) and does the inner tub turn freely, or is it rubbing on the outer tub?
2] is the door rubber sverely mishapen or distorted and not aligned with the door opening?
3] is the machine more noisy than normal?
4] Is the washing action normal or not?
If you have any of the problems from 1-3 above, then it is possible that you have danaged the inner tub or bearings.
If the wash action is NOT normal {No. 4}, it could also indicate a motor fault too.
One of the suspension dampers may have colapsed if the tub does not align with the door opening properly.

Without more information, or seeing the machine it is difficult do give a more positive diagnosis, but I hope this helps?

Jul 01, 2016 | LG Washing Machines

1 Answer

Wash down


That would depend on what you want to do with it. Although something that big cannot adequately spin out at high speed because it cannot balance itself. So if you select a setting with a highspeed spin it wont make it to the high speed.

Apr 28, 2014 | LG WM2240CW - Front Load Washer with LED...

1 Answer

Bearing noise in a lg washer


Check your owners manual, some models warranty the rear tub that houses the bearing and the inner spin basket. If not the rear outer tub and the gasket between both tubs will have to be replaced the correct the problem. If out of warranty it may not be cost effective to repair.

Apr 04, 2014 | LG WM2016CW Front Load Washer

1 Answer

I have an LG Tromm front load washer. During the spin cycle it sounds like a plane is taking off and now I smell burning. Could anyone tell me what is happening. and what I need to replace in it. ...


It's not the gasket but the bearings at the back of the drum which are going. These can be replaced in some machines where you can split the drum but I'm not sure about LG. You can buy bearing kits by quoting the model number and serial or product number usually found on the inside of the door. This can be a laborious task and depending on how bad the bearings are in the machine an almost impossible task. My advice it's a new machine or check the manufacturers parts guarantee, you might be covered for parts only.
Hope this helps

Sep 17, 2013 | LG WM-2277HW Front Load Washer

2 Answers

LG WM-1832 Awful noise - Spider in broken - How to fix ?


Seems like you need beaucoup parts and with what they charge for parts you just might be better off getting a new machine.

If you go to the attached link you can find out the part numbers and prices of the parts you want - if you ask them your question they will have the answer for you right there. http://www.appliancepartspros.com

Mar 24, 2017 | LG WM-1832C Front Load Washer

2 Answers

My LG TROMM model # WM1812CW has a burning rubber smell when it's on the last high speed cycle. Can you help me locate the problem?


I just ran into this same situation. The problem was that the basket has been rubbing against the tub/door gasket. In this specific case it finally wore through the tub and was a hole through it. It si looking to be approx a $600 repair.

Sep 03, 2010 | LG WM1812C Front Load Washer

2 Answers

LG washing machine WM2277H tub off center does not spin electronically, manually its spins but rubs sides


Normal 0 MicrosoftInternetExplorer4 /* Style Definitions */ table.MsoNormalTable {mso-style-name:"Table Normal"; mso-tstyle-rowband-size:0; mso-tstyle-colband-size:0; mso-style-noshow:yes; mso-style-parent:""; mso-padding-alt:0in 5.4pt 0in 5.4pt; mso-para-margin:0in; mso-para-margin-bottom:.0001pt; mso-pagination:widow-orphan; font-size:10.0pt; font-family:"Times New Roman";} Hi,

When my washer did that, I found that the shocks that hold the tub were bad...

Check out this tip I wrote about the noise and vibration that front load washers can make..

Washer Problems Washer noise when spinning


heatman101

Sep 02, 2010 | LG WM2277H Front Load Washer

1 Answer

Lg wm2277hw. Shortly after wash cycle begins a loud brrrring noise starts from the front of the machine. It seems to be coming from just above the clean out on the lower left front of the machine. I have...


Try just manually turning the wash tub to see if you have the noise at that time. There may to an object rubbing on the tub. Look around the very front edge of the tub, right near the rubber door gasket. (note: if you spin the drum quickly, the control will light for a few seconds, due to the fact that you are actually using the motor to generate a little electrical current. This is not harmful to the machine.) Let me know what your results are, and if we will have to look further / elsewhere.

May 17, 2009 | LG WM-2277HW Front Load Washer

Not finding what you are looking for?

Open Questions:

Washing Machines Logo

Related Topics:

39 people viewed this question

Ask a Question

Usually answered in minutes!

Top LG Washing Machines Experts

Gerry Harvey
Gerry Harvey

Level 3 Expert

1481 Answers

Marvin
Marvin

Level 3 Expert

85160 Answers

jimorris77

Level 3 Expert

411 Answers

Are you a LG Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...