Question about Washing Machines

1 Answer

Do I use grease on the shaft of wtw6200sw0 washer. And is there anywhere else?

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 61 Answers

Hi Lori, you shouldn't have to grease anything on that machine. What is the problem with the washer that you think you have to grease it? If it's squeaking while it's in the spin cycle,it has a leaking tub bearing and the bearings need to be replaced. You should call your local repair company to check it out and give you a price quote. Hope that helps.

Posted on Aug 10, 2019

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a Sears Kenmore washer (Model # 11092281100). I replaced the motor coupler, and I checked the alignment of everything before reconnecting the motor clamps/clips. It seemed like the motor shaft was...


It could be the grease. It could run without noise if it was not installed all the way. Here is a link for properly installing Motor coupler video Now if everything looks right it is probally just the grease.

Nov 09, 2010 | Kenmore 3.2 cu. ft. Plus Top Load Washer

1 Answer

My washer model number wtw6200sw0 keeps giving me an f1 error code. what do i do?


Primary Control Failure
F then 1 flashes when there is a primary control failure. Replace
the machine/motor control assembly. See Accessing &
Removing the Electronic Assemblies, page 14.

WTW6200SW0
Tech Sheet


If you need further help, reach me via phone at https://www.6ya.com/expert/dan_73bbd84fe1d95b61

Aug 10, 2010 | Whirlpool Washing Machines

1 Answer

Kenmore 80 Series washer leaves brown grease marks


Remove the agitator and check the shaft seal underneath the plastic drive block at the top of the shaft. Move the shaft in different directions to check the condition of the top bearing. If none or very slight, replace the seal at the top of the shaft supporting post. Clean any grease that is outside of the seal when you are done. Be sure to not damage the seal surface on the shaft when removing/replacing the seal and pre-grease the new seal's inner lip before installing.

Nov 15, 2009 | Kenmore 22422 Top Load Washer

1 Answer

Fairly new ge washer spitts out grease/oil from under agitater


Remove the agitator and inspect the upper shaft bearing condition by trying to push the shaft in various directions. It should not be possible to observe movement in a good bearing. If the bearing looks good, then replace the rubber seal just under the plastic block on the shaft top. You must be very careful not to damage the shaft where the seal lip rides. If the bearing is loose, the machine must be torn down to remove the shaft from the supporting post.

Aug 15, 2009 | Washing Machines

2 Answers

I AM REPLACING THE BASKET ASSEMBLY ON MY KENMORE FRONT LOAD WASHE


The shaft on the spin basket assembly is not lubricated. The shaft is inserted through the sealed bearings located in the rear outer tub shell. Placing any grease on the shaft would end up in your wash and damage your clothes.

Apr 03, 2009 | Kenmore 42822 Front Load Washer

1 Answer

Sears Kenmore washer shaft grease?


Yes auto parts,home depot or appliances store you can use all purpose grease good luck .

Oct 31, 2017 | Kenmore Washing Machines

1 Answer

Maytag washer tub seal bearing kit - grease?


how do i change bearings and shaft ona maytag washer model# mvwb300wq0

Jun 17, 2008 | Washing Machines

1 Answer

Replacement grease for drum shaft seal


you really dont have to use any at all unless you have removed all of it.Remember 99% of these bearings are self lubricating.

May 21, 2008 | Frigidaire ATF6000ES Front Load Washer

1 Answer

Grease spots on clothes


Your drum support bracket grease shaft seal (which will require a new Lip Seal Kit #12002022) is dead and potentialy the two shaft bearing are at risk. Parts cost retail approx. $100 or so. Labor, Lookout...
I'm fighting this issue for the second time.......
Bill B.

May 20, 2008 | Maytag Neptune MAH7500WH Front Load Washer

Not finding what you are looking for?
Washing Machines Logo

Related Topics:

52 people viewed this question

Ask a Question

Usually answered in minutes!

Top Washing Machines Experts

Gerry Harvey
Gerry Harvey

Level 3 Expert

1481 Answers

Marvin
Marvin

Level 3 Expert

85206 Answers

Brad Brown

Level 3 Expert

18108 Answers

Are you a Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...