Question about Televison & Video

2 Answers

I turned it off before bed and when i got up this morning my tv will not power on

Posted by on

Ad

2 Answers

  • Level 1:

    An expert who has achieved level 1.

    New Friend:

    An expert that has 1 follower.

  • Contributor
  • 4 Answers

Transformer dead

Posted on Aug 17, 2019

Ad
  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Televison & ... Master
  • 2,473 Answers

Unplug it from the electrical outlet. On the physical TV, depress the power button (on button) and keep it depressed for 30 seconds. Release the button. Plug the TV back in. Try turning it on with the physical button, not the TV remote.

That might reset the TV.

You have not indicated if there are other symptoms such as a blinking light. And we have not ruled out such things such as a battery in the remote being loose and thus the remote fails to work. Or, something physical is blocking the signal from the remote. Or a fuse has blown to the power outlet that the TV is connected to. Such things have to be ruled out.

Posted on Aug 17, 2019

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My sony trinitron is blinking red and won't turn on


THIS IS NORMALY CAPACITORS IN THE POWER SUPPLY THAT NEED REPLACING

Jun 25, 2013 | Sony FD Trinitron WEGA KV-34HS510 34" TV

1 Answer

II turned my tv off to go to bed but when I went to turn it on this morning it would not come on.


going to have to look inside the set, follow the power cord to the main ac fuse and see if bad or good.

Dec 22, 2012 | Sanyo PLV-55WM1 55" HDTV-Ready LCD TV

1 Answer

I have a JVC model HD-52G886 tv. that loses sound.


Replace or have replaced the Audio board in the set----a lot of them fail.

Mar 12, 2012 | JVC HD-52G786 52" Rear Projection HDTV

1 Answer

When i went to bed, i turned the Daewoo TV off. Then when i tried to turn it on in the morning there was no power. No lights come on but the fuse is fine.


A total failure can be a result of a power failure in the TV. so to check the main power which is a SMPS unit - switch mode power supply- remove plug, remove the poser section and check;
check for tips on the link below;

http://www.fixya.com/support/r5826301-working_switch_mode_power_supplies

May 19, 2011 | Televison & Video

1 Answer

Last night I was watching TV just fine. I turned off the TV when I went to bed and then tried to turn it back on this morning when I got up. It wont turn back on and I have checked to make sure that there...


Check ur power source?Tries tv unplug,replug the tv back like about an hour later.Now the tv are resetting it self back to the factory setting.The tv should work now.If still have the same problems,some how ur power supply board is causes and is not providing the tv the wright voltages anymore.That the board,where the power a/c cord plug into it.Tries websites like Shopjimmy.com,Ebay.com to buy a whole refurbish power supply board for the replacement.

Dec 09, 2010 | Mitsubishi LT-40133 40 in. LCD HDTV

1 Answer

How to replace power supply?


Toshiba model 57H93 worked perfectly last night. Turned off and went to bed. Turned on this morning, and nothing, it won't turn on. Checked all cords and cables, pushed reset button, and still won't turn on. What could cause this to happen?

Dec 14, 2009 | Toshiba 57H93 57" Rear Projection HDTV

1 Answer

TV will not come on.


check to see if the power cord is pluged in firmly

Dec 17, 2008 | Sylvania 6427GFG 27" TV

1 Answer

Sunbeam 4267-000 not turning on just blinking red


"FF" or a blinking light will display meaning “Fault Found”. The “fault” is in the amount of power available to the blanket, mattress pad or throw.
There are several causes to this problem:
1. Bedding product is plugged into an extension cord, surge protector, power strip, or not plugged into a direct wall outlet.
2. Bedding product wasn't plugged in properly.

To FIX this problem, do the following to reset your bedding product:
1. Unplug the power cord from the electrical connection.
2. Unplug the cord from the actual bedding product itself.
3. Re-plug the cord into the bedding product. Make sure the connection is secure and complete.
4. Re-insert power cord back into a wall outlet.

If the 4 steps above are not followed in order, the bedding product will not properly reset.

Dec 08, 2008 | Sunbeam 4237 / 4238 Iron with Auto...

Not finding what you are looking for?
Televison & Video Logo

Related Topics:

13 people viewed this question

Ask a Question

Usually answered in minutes!

Top Televison & Video Experts

The Knight
The Knight

Level 3 Expert

76125 Answers

Ekse

Level 3 Expert

13434 Answers

Cindy Wells

Level 3 Expert

6006 Answers

Are you a Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...